Streszczenie treści zawartej na stronie nr. 1
model h6330
1
2 ⁄4 gallon paint tanK
instruction manual
Copyright © MAy, 2008 By grizzly industriAl, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#JM10748 printed in ChinA
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
safety for your own safety read instruction manual before operating this equipment t he purpose of safety symbols is to attract your attention to possible hazardous conditions. t his manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. t he progression of symbols is described below. r emember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. in
Streszczenie treści zawartej na stronie nr. 4
7. avoid entanglements. do not 16. do not force tool. it will do wear loose clothing, gloves, neck- the job better and safer at the rate ties, rings, bracelets, or other jewel- for which it was designed. ry, which may get caught in moving 17. checK for damaged parts parts, when operating this tool. Wear before using. Check for bind- a protective hair covering to contain ing and alignment of parts, broken long hair. parts, part mounting, loose bolts, 8. use correct air pressure. and any oth
Streszczenie treści zawartej na stronie nr. 5
a dditional safety instructions for paint t anks 1. read this manual. this manual 6. removing lid. do not try to remove the lid while the tank is under pressure, contains proper operating instructions or the lid could explode from the tank. for this paint tank. Follow the instructions in this manual 2. design modifications. d o not for relieving pressure in the tank before modify the tank design or construction. removing the lid. drilling into the tank or weld attach- 7. lid clamps. ove
Streszczenie treści zawartej na stronie nr. 6
introduction f oreword specifications t he specifications, details, and paint tank photographs in this manual represent 1 Material Capacity ...........2 /4 gallons (8.5 l) the Model h 6330 as supplied when the operating pressure ....................25–30 psi manual was prepared. h owever, owing to Maximum operating pressure .........50 psi g rizzly’s policy of continuous improvement, tank Construction ........... galvanized steel changes may be made at any time with no obligation on the p
Streszczenie treści zawartej na stronie nr. 7
setup unpacking inventory your paint tank was carefully packaged for h 6330 inventory (f igure 1) ............... Qty 1 safe shipping. if you discover any damage a . paint t ank 2 ⁄4 gallon .......................... 1 after you have signed for delivery, immedi- b. l id ........................................................ 1 ately call Customer Service at (570) 546- c. r egulator Assembly ............................ 1 9663 for advice. d. l ift h andle .....................................
Streszczenie treści zawartej na stronie nr. 8
t ank a ssembly pressure gauge lift handle regulator Assembly Air inlet Fitting Air outlet Fitting Fluid outlet Adapter safety Valve figure 2. regulator and lift handle installed on paint tank. 1 to assemble the paint tank: 6. Connect a /4" npt material hose (not included) to the fluid outlet adapter on 1. Apply pipe thread tape to all male pipe the tank lid. threads. 7. install a pressure regulator (not includ- 2. thread the lift handle into the center ed), between the tank regulator, (figure
Streszczenie treści zawartej na stronie nr. 9
operations t ank r egulator t he pressure regulator on the paint tank controls the amount of pressure in the paint tank and the spray gun. t he following are operating guidelines for internal and external spray guns: respiratory hazard ! a lways use a niosh ap proved respirator when internal mix g uns: use higher tank using spray equipment. f ailure to pressures up to the full amount of air protect your lungs can lead to respi- pressure being delivered to the spray gun. ratory illness
Streszczenie treści zawartej na stronie nr. 10
3. place the lid assembly on the tank and evenly hand tighten the lid clamp wing screws. 4. Adjust the regulator at your air com- pressor to 50 psi. 5. Fully turn the regulator t-handle coun- terclockwise to shut the tank regulator OFF. r ead the manual before operation. become familiar with this tool, its safety instructions, and its operation before beginning any work. serious personal injury may result if safety or operational information is not regulator understood or followed. t-ha
Streszczenie treści zawartej na stronie nr. 11
cleaning and lubrication 3. turn the tank regulator t-handle coun- c leaning the t ank terclockwise until you no longer feel spring tension. proper cleaning is the best way to ensure 4. loosen the wing screws on the tank lid trouble free performance from your paint (figure 4), tip the clamps back, and tip tank. if your tank is not thoroughly cleaned, the tank lid to one side. damage and poor operation will result. problems caused by improper cleaning will 5. loosen the spray gun atomiz
Streszczenie treści zawartej na stronie nr. 12
t ank t roubleshooting symptom possible cause solution Air escaping from 1. Broken or damaged dia- 1. replace tank regulator. regulator port. phragm in tank regulator. pressure dropping 1. dirty or worn valve seat in 1. replace tank regulator. slowly on regulator. regulator. 2. loose air fittings leaking air. 2. tighten loose air fittings or remove and re-install with new pipe thread tape. Fluid or air leak at 1. defective lid gasket. 1. replace lid gasket. lid gasket. 2. Wing screw loose. 2.
Streszczenie treści zawartej na stronie nr. 13
h6330 paint tan K TO REDUCE RISK OF SERIOUS INJURY WHEN USING THIS EQUIPMENT: 1. Do not exceed 50 PSI. 2. Do not use attachments with lower pressure H6330 21⁄4 GAL. PAINT TANK ratings than the adjusted tank pressure. 3. Do not modify tank or substitute inferior components. Capacity: 2 ⁄ Gallons 4. Do not tamper with safety valve. Gun Type: Pressure Feed (HVLP or 5. Do not remove lid while tank is under Conventional) pressure. Always turn off air pressure at the Maximum Pressure: 50 P
Streszczenie treści zawartej na stronie nr. 14
Warranty grizzly industrial, inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. this warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance. this is grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the durati
Streszczenie treści zawartej na stronie nr. 15
Warranty card name _________________________________________________________________ street _________________________________________________________________ City _______________________ state _________________________ zip _________ phone # ____________________ email ________________________ invoice # _____ Model # ____________________ order # _______________________ serial # ______ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develo
Streszczenie treści zawartej na stronie nr. 16
send a grizzly catalog to a friend: name________________________________ street________________________________ city______________state______zip_______ fold along dotted line place stamp here grizzly industrial, inc. p.o. boX 2069 bellingham, Wa 98227-2069 tape along edges--please do not staple
