Streszczenie treści zawartej na stronie nr. 1
TELEDYNE
HASTINGS
INSTRUMENTS
INSTRUCTION MANUAL
HFM-I-401 AND HFM-I-405
INDUSTRIAL
FLOW METERS
- i -
Streszczenie treści zawartej na stronie nr. 2
Manual Print History The print history shown below lists the printing dates of all revisions and addenda created for this manual. The revision level letter increases alphabetically as the manual undergoes subsequent updates. Addenda, which are released between revisions, contain important change information that the user should incorporate immediately into the manual. Addenda are numbered sequentially. When a new revision is created, all addenda associated with the previous revision of
Streszczenie treści zawartej na stronie nr. 3
VSUP - VSUP + A OUT- A OUT + A IN + A IN - DCOM ZERO ALARM1 ALARM2 ALARM- General Information Quick Start Instructions Connect dry, clean gas and ensure connections are Connect Cable for power and analog signal output. leak free. Check that electrical connections are correct. Replace front cover and cable feed-through ensuring (See diagrams below) gasket is seated and fasteners are secure. 12 1 Terminal Strip PINS RS232 RS485 ETHERNET SHIELD GROUND GROUND GROUND 12 1 TRANSMIT TX+
Streszczenie treści zawartej na stronie nr. 4
This instrument is available with multiple pin-outs. Ensure electrical connections are correct. CAUTION The 400-I series flow meters are designed for IEC Installation/Over voltage Category II – single phase receptacle connected loads. CAUTION The Hastings 400 Series flow meters are designed for INDOOR and OUTDOOR operation. NOTE In order to maintain the integrity of the Electrostatic Discharge immunity both parts of the remote mounted version of the
Streszczenie treści zawartej na stronie nr. 5
General Information Table of Contents GENERAL INFORMATION.....................................................................................................................................1 1. GENERAL INFORMATION ....................................................................................................................................1 1.1. OVERVIEW......................................................................................................................................
Streszczenie treści zawartej na stronie nr. 6
5.1. WARRANTY REPAIR POLICY.........................................................................................................................21 5.2. NON-WARRANTY REPAIR POLICY................................................................................................................21 APPENDICES............................................................................................................................................................22 6. APPENDICES .................
Streszczenie treści zawartej na stronie nr. 7
General Information 1. General Information 1.1. Overview 1.1.1. 400 Series Family The Hastings 400 Series is a family of flow instruments which is specifically designed to meet the needs of the industrial gas flow market. The “I” family in the 400 Series features an IP-65 enclosure which allows the use of the instrument in a wide variety of environments. The 400 I products consist of four configurations: a flow meter, HFM-I-401, which has a nominal nitrogen full scale between 10 SLM
Streszczenie treści zawartej na stronie nr. 8
1.1.4. Additional Functions These instruments contain a number of functions in addition to reporting flow which include: • Settable alarms and warnings with semiconductor switch outputs • A digitally reported status of alarms and warnings such as overflow/underflow • A flow totalizer to track the amount of gas added to a system • A digitizing channel for an auxiliary analog signal • An internal curve fitting routine for “fine tuning” the base calibration • An alternate calibration
Streszczenie treści zawartej na stronie nr. 9
Digital Connector 4 pin, D-coded M12 4 pin, D-coded M12 Mechanical Fittings Standard: 1/2" Swagelok Standard: 1" Swagelok Optional: ½" VCO®, ½" VCR®, ¾” Swagelok, Optional: 1" VCO®,1" VCR®, ¾” Swagelok, , 10mm Swagelok, 3/8" male NPT, ½” male NPT 1" male NPT, ¾” male NPT, 1 5/16"-12 straight 12mm Swagelok, ¾"-16 SAE/MS straight thread thread -8 -8 Leak Integrity < 1x10 sccs He < 1x10 sccs He Wetted Materials 316L SS, Nickel 200, 302 SS, Viton® 316L SS, Nickel 200,
Streszczenie treści zawartej na stronie nr. 10
Installation 2. Installation Many of the functions described in this section require removing the enclosure front plate. Care must be taken when reinstalling this plate to ensure that the sealing gasket is properly positioned and the fasteners are secure to maintain CAUTION an IP65 compliant seal. 2.1. Receiving Inspection Your instrument has been manufactured, calibrated, and carefully packed so it is ready for operation. However, please inspect all items for any obvious signs of
Streszczenie treści zawartej na stronie nr. 11
2.4. Mounting the Electronics Remotely In order to maintain the integrity of the Electrostatic Discharge immunity both parts of the remote mounted version of the HFM-I-400 instrument must be screwed to a well grounded structure. The ferrite that is shipped with the instrument must CAUTION be installed on the cable next to the electronics enclosure. The electronics enclosure can be separated and relocated up to 30 feet away from the flow meter base. This requires a cable which is
Streszczenie treści zawartej na stronie nr. 12
In order to maintain the environmental integrity of the enclosure the power/signal cable jacket must have a diameter of .157 - .315” (4 – 11 mm). The nut on the cable gland must be tightened down sufficiently to secure the cable. This cable CAUTION must be rated for at least 85°C. 2.5.1. Power Supply Ensure that the power source meets the requirements detailed in the specifications section. Hastings offers several power supply and readout products that meet these standards and are
Streszczenie treści zawartej na stronie nr. 13
Figure 2-4 shows an arrangement using a separate loop supply which is isolated from the instrument power supply. Figure 2-3 Wiring diagram showing the current loop supply powered by the instrument supply Figure 2-4 Wiring diagram showing the current loop powered by an external supply - 7 -
Streszczenie treści zawartej na stronie nr. 14
2.5.2.2. Voltage output If the flow meter is configured for a voltage output, the signal will be available as a positive potential on pin 4 relative to pin 3 of the terminal strip. Since these pins are galvanically isolated, the signal cannot be read by an indicator between pin 4 and pin 1 of the terminal strip. Pin 3 must be used as the return to properly read the output on pin 4. If an output that is referenced to power supply common is desired then pins 3 and 1 must be connected. It is
Streszczenie treści zawartej na stronie nr. 15
electronics enclosure. Only the state of jumpers 1, 2, and 5 affect the RS-232 operation. These jumpers are installed vertically over two pins when enabled and are numbered from left to right. Jumper 1 must be disabled for RS-232; jumper 2 is used to select half or full duplex; and jumper 5 is enabled when a hardware override of the baud rate (forcing it to 9600) is desired. These functions are summarized in Figure 2-6. 2.7.2. RS-485 If RS485 is specified on the order, the flow meter i
Streszczenie treści zawartej na stronie nr. 16
2.8. Alarm Output Connection The Hastings 400 Series flow meters include two software settable hardware alarms. Each is an open-collector transistor functioning as a semiconductor switch designed to conduct DC Alarm 1 current when activated. (See Figure 2-9.) These sink sufficient current to illuminate an external LED or to activate a remote relay and can tolerate up to 70Vdc across the transistor. The alarm lines and the alarm common are Alarm 2 galvanically isolated from all other
Streszczenie treści zawartej na stronie nr. 17
2.9. Auxiliary Input Connection The Hastings 400 Series flow meters provide an auxiliary analog input function. The flow meter can read the analog value present between pins 5 and 6 on the terminal strip (as shown in Figure 2-2) and make its value available via the digital interface. The accepted electrical input signal is the same as that configured for the analog output signal (4 – 20 mA, 0 -20 mA, 0-5 Vdc, 1-5 Vdc, or 0-10 Vdc). Unlike the analog output signal, which is isolated and
Streszczenie treści zawartej na stronie nr. 18
Calibrated gas = Nitrogen (GCF = 1.000) 1 Full scale range (FS ) = 100 slm 1 Secondary gas (FS ) = Hydrogen (GCF = 1.0038) 2 2 1.0038/1 = 1.0038, 1.0038 x 100 = 100.38 slm of Hydrogen Example 2- Changing the active gas record Selecting the active gas record is accomplished in one of two ways: 1. Hardware setting 2. Software setting Hardware: The hardware setting is selected by accessing a rotary encoder on the upper PC board in the electronics enclosure. When set to a number po
Streszczenie treści zawartej na stronie nr. 19
Check mounting and mechanical installation including flow direction Insure flow connections are leak tight Check digital M12 connector and/or cable Verify power connections on analog terminal strip + Vsup → pin 1 -Vsup → pin 2 Check Model # Digital and Software Check/Set IP Communications Revision address RS-232 Ethernet Interface S1 Verify output and other RS-485 connections on analog terminal strip Check Serial (See Section 2.?) Complete Number Check Model # S68 and Software
Streszczenie treści zawartej na stronie nr. 20
Operation 3. Operation The Hastings 400 Series flow meters are designed for operation with clean dry gas and in specified environmental conditions (See Section 1.2). The properly installed meter measures and reports the mass flow as an analog signal and, depending on the configuration and set up, as a digital response. Other features can assist in the measurement operation and provide additional functions. The following sections serves as a guide for correctly interpreting the analog and d
