Streszczenie treści zawartej na stronie nr. 1
CRW2216E
SERIES
User Guide
Guide de l’utilisateur
Bedienungsanleitung
ON/ READ/
DISC WRITE
Deutsch Français English
Streszczenie treści zawartej na stronie nr. 2
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Systems Technology, Inc. Address: 100 Century Center Court San Jose, California 95112 Telephone: (408) 467-2330 FAX: (408) 437-8791 Type of Equipment: CD Recorder Model Name: CRW2216E CRW2216E-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference rec
Streszczenie treści zawartej na stronie nr. 3
Laser Diode Properties CAUTION Material : GaAlAs Use of controls or adjustments or performance of Wavelength : 783-789 nm procedures other than those specified herein may Emission Duration : Continuous result in hazardous radiation exposure. Laser Output Power : Less than 44.6 m W* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 This compact disc player is classified as a CLASS 1 CLASS 1 LASER PRODUCT LA
Streszczenie treści zawartej na stronie nr. 4
WARNING WARNING ¢ WARNING ¢ • The temperature where CRW2216E is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW2216E cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW2216E. i
Streszczenie treści zawartej na stronie nr. 5
Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW2216E. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW2216E before recording is finished, store the disc in a clean, dust- free environment. • The CR
Streszczenie treści zawartej na stronie nr. 6
Table of Contents Table of Contents Introduction ...............................................................................1 CRW2216E Features .......................................................1 Orange Book Compatible Recording ..............................2 Chapter 1 - System Configuration .......................................3 Computer .........................................................................3 Software ...............................................
Streszczenie treści zawartej na stronie nr. 7
Introduction Introduction Thank you for purchasing a Yamaha CRW2216E drive. Please read this manual before using the drive in order to make the best use of the superior CRW2216E functions. After reading, please retain this manual for future reference. CRW2216E Features n 2xS Recording (Rewritable) - 2xS Recording (Recordable) - 16xS Reading The CRW2216E is able to write (overwrite) CD-RW discs at double speed, and is able to write CD-R discs at double speed, or normal speed
Streszczenie treści zawartej na stronie nr. 8
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD- ROM drives other than a CD-RW or a CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not p
Streszczenie treści zawartej na stronie nr. 9
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW2216E, make sure that you have all of the items on the list of included items. In order to use the CRW2216E, you will require the following. Computer The following operating environment is required: • An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU • A vacant IDE interface connector • A vacant half-height bay • Windows 95, Windows 98 or Windows NT4.0(Service Pack 3) • Sufficient ha
Streszczenie treści zawartej na stronie nr. 10
Chapter 1 - System Configuration Tools Phillips screwdriver This is used to remove the Phillips Screwdriver cover of your computer, and to install the Yamaha CRW2216E drive. Long nose pliers These are used to insert or remove the jumper pin when setting the MASTER/SLAVE settings of the Yamaha CRW2216E drive. Long nose pliers Discs n CD-R discs Please use discs that are compliant with Orange Book Part 2. (If you wish to write data at 4X speed, you must use discs which s
Streszczenie treści zawartej na stronie nr. 11
Chapter 2 - Installing the Yamaha CRW2216E Drive Chapter 2 - Installing the Yamaha CRW2216E Drive MASTER/SLAVE settings Before you install the CRW2216E in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW2216E drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin.
Streszczenie treści zawartej na stronie nr. 12
Chapter 2 - Installing the Yamaha CRW2216E Drive Setting the CRW2216E as the MASTER As shown in the diagram at the right, insert the CSEL SLAVE jumper pin into the right edge of the jumper MASTER switch. Note: If only the CRW2216E will be connected to the IDE interface connector, connect the CRW2216E to the end of the connector. Setting the CRW2216E as the SLAVE As shown in the diagram at the right, insert the CSEL SLAVE jumper pin into the middle of the jumper MASTER switch. CS
Streszczenie treści zawartej na stronie nr. 13
OFF Chapter 2 - Installing the Yamaha CRW2216E Drive Installing the CRW2216E drive The following steps will differ slightly depending on the type of com- puter you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. (This user guide assumes that a SCSI card has already been installed.) 1. Switch off your computer, and unplug it from the AC outlet. If you fail to do this, there is a danger
Streszczenie treści zawartej na stronie nr. 14
ON/ READ/ DISC WRITE VOL Chapter 2 - Installing the Yamaha CRW2216E Drive 3. Your hands or body may be holding a charge of static elec- tricity. Touch a metallic portion of the chassis or power supply to release any such charge. 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Slide the CRW2216E drive into the drive bay from the front. At this time, be careful not to apply excessive force to the drive itself. Finger-tighte
Streszczenie treści zawartej na stronie nr. 15
Chapter 2 - Installing the Yamaha CRW2216E Drive 6. Connect the IDE interface connector. Connect the 40-pin IDE interface connector to the IDE interface located on the rear panel of the CRW2216E drive. Position the connector so that the colored line is at pin 1 (your lower right). 7. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT c
Streszczenie treści zawartej na stronie nr. 16
Chapter 2 - Installing the Yamaha CRW2216E Drive AUDIO cable To the CRW2216E 4-pin connector (large) To the Sound Card (Sound Blaster compatible) 4-pin connector (small) 8. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW2216E drive. The shape of the connector makes it impossible to reverse the connec- tions. If you have difficulty when inserting the connector, try wiggling the connector left and right
Streszczenie treści zawartej na stronie nr. 17
ON/ REA / D DISC WRITE VOL Chapter 2 - Installing the Yamaha CRW2216E Drive 9. Tighten the four fastening screws securely. 10. Attach the cover of your computer. 11. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW2216E drive is lit. 12. Start up your operating system, and verify that the CRW2216E is recognized by the operating system. For the procedure, refer to the manual for your operation system. 13. Install the wr
Streszczenie treści zawartej na stronie nr. 18
Chapter 3 - Operation Chapter 3 - Operation Front Panel 1 7 6 ON/ READ/ DISC WRITE VOL 2 3 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level. 4 ON/DISC LED This indicator lights up in orange when the C
Streszczenie treści zawartej na stronie nr. 19
Chapter 3 - Operation 6 Eject button This button is used to open or close the tray. 7 Manual Eject hole This is used to manually eject a disc that cannot be ejected in the nor- mal way. It is for emergency use only. Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the eject button again to close the disc tray. 13 ON/ READ/ DISC WRITE VOL
Streszczenie treści zawartej na stronie nr. 20
Chapter 3 - Operation Ejecting the Disc If the CRW2216E is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the ATAPI command prohibits the eject operation while the CRW2216E is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.) Press the eject button If the CRW2216E is not powered on: Pressing the eject button will not eject th
