Streszczenie treści zawartej na stronie nr. 1
OWNER'S MANUAL
EHVS-80CS Edge Horizontal/Vertical Sander
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax 253-939-8001
www.jettools.com e-mail jet@jettools.com M-708448
Streszczenie treści zawartej na stronie nr. 2
This manual has been prepared for the owner and operators of a JET EHVS-80CS Sander. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your sander, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warranty & Service
Streszczenie treści zawartej na stronie nr. 3
WARNING 1. Read and understand the entire 12. Make certain the switch is in the OFF instruction manual before attempting position before connecting the machine to assembly or operation. the power supply. 13. Give your work undivided attention. 2. This sander is designed and intended for Looking around, carrying on a conversation, use by properly trained and experienced and "horse-play" are careless acts that can personnel only. If you are not familiar result in serious injury. with the proper
Streszczenie treści zawartej na stronie nr. 4
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and o
Streszczenie treści zawartej na stronie nr. 5
230 Volt Operation WARNING! All electrical connections must be done by a qualified electrician! Failure to comply may result in serious injury! If 230V operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This sander is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug (A), supplied wit
Streszczenie treści zawartej na stronie nr. 6
Specifications: EHVS-80CS Stock Number................................................................................................................................ 708448 Fence ....................................................................................................................................... 4”H x 24”L Abrasive Belt Size ................................................................................................................... 6”W x 89”L Dust Chute Diameter .......
Streszczenie treści zawartej na stronie nr. 7
Contents of the Shipping Container 1. Stand (front) 1. Stand (rear) 2. Stand (sides) 1. Extension Table Assembly 1. Extension Cover 1. Owner’s Manual 1. Warranty Card 1. Sanding Unit with Motor 1. Back Stop 1. Handle 1. Driver Wrench 1. Miter Gauge Assembly 1. Sanding Belt 1. Adjusting Wrench 1. Assembly Hardware: Cabinet 1. Lock Knob (20mm Length) 2. Lock Knob (12mm Length) 1. Lock Knob (35mm Length) 4. Cabinet Pads 4. 5/16” x 5/8” Screws 22. 5/16” Flat Washers 12. 5/16” Hex Nuts 8. 5/16” x 5/8
Streszczenie treści zawartej na stronie nr. 8
Assembly 1. Remove all contents from the shipping container. 2. Clean all rust protected surfaces with a mild solvent. Do not use paint or lacquer thinner, gasoline, or mineral spirits; these will damage painted surfaces. 3. Attach the four rubber pads (A, Fig. 1) to the bottoms of the side panels with four 5/16” x 5/8” Screws, four 5/16” flat washers and four 5/16” hex nuts (B, Fig. 1). The hardware can be found in the bag with the rubber pads. 4. Attach the side panels (C, Fig. 1) to the front
Streszczenie treści zawartej na stronie nr. 9
10. Sanding platen is presently in a horizontal 21. Reinstall the guards and secure in place position. Pull lock handle forward (A, Fig. 3) with lock knobs. to unlock platen assembly, tilt sanding platen to the vertical position, and push lock 22. Attach the extension cover (D, Fig. 6) with handle to lock platen assembly in place. three pan head screws and one lock knob. Note: do not turn lock handle. Turning or rotating the lock handle will change the tension of the locking assembly. This may c
Streszczenie treści zawartej na stronie nr. 10
WARNING Removing the belt guard exposes more of the sanding belt! Replace the belt guards immediately after completing any sanding that requires it’s removal! Failure to comply may cause serious injury! Horizontal Sanding With the sanding platen locked in the horizontal position, the removable fence (A, Fig. 6) may be used. The fence can be secured in place by screwing two lock knobs (B, Fig. 6) into the guide blocks found in the miter slot. Adjust the table so the fence is at a good height, s
Streszczenie treści zawartej na stronie nr. 11
Platen Lock Tension Adjustment 1. Disconnect the machine from the power source. 2. Loosen lock handle by pulling forward (A, Fig. 9) and move motor and sanding table toward the horizontal position. Do not lock. 3. Tension eccentric block by tightening the nyloc nut (B, Fig. 9) with a 14mm wrench. Turn the nut in ¼ turn increments and test locking handle for proper tension. Locking handle is properly tensioned when it requires positive force to move the eccentric block (attached to the locking ha
Streszczenie treści zawartej na stronie nr. 12
3. Insert the driver with the round shaft, supplied with the machine into the micro adjusting nut (A, Fig. 11) and turn away from you to loosen. 4. Turn the micro adjusting screw (B, Fig. 11) in ¼ turn increments until the belt tracks evenly on the rollers when rotated by hand. 5. Tighten the micro adjusting nut (A, Fig. 11). 6. Connect the machine to power. 7. Turn on the power to the machine just enough to start the belt rotating and then turn off. Do this several times and observe belt tracki
Streszczenie treści zawartej na stronie nr. 13
Table Adjustment WARNING Do not position table below sanding belt! Keep an overlap of at least 1/16” between table and sanding belt to avoid material and/or fingers getting caught! Failure to comply may cause serious injury! 1. Loosen two lock knobs (A, Fig. 13). 2. Raise or lower work table to desired level. 3. Tighten two lock knobs. Troubleshooting Trouble Possible Cause Solution 1. Sander unplugged from wall 1. Check all plug connections or motor 2. Replace fuse or reset circuit Sander wil
Streszczenie treści zawartej na stronie nr. 14
Table and Motor Assembly 14
Streszczenie treści zawartej na stronie nr. 15
Parts List For The EHVS-80CS Sander Table and Motor Assembly Index Part No. No. Description Size Qty. 1..........EHVS80CS-01 ................. Base.............................................................. .................................1 2..........994532............................. Switch (serial #: 9031435 and lower) ............. .................................1 ............EHVS80-02N ................... Push Button Switch (serial #: 9031436 and higher) .........................1 3.
Streszczenie treści zawartej na stronie nr. 16
Index Part No. No. Description Size Qty. 37A......EHVS80-37A.................... Pin................................................................. M6x40mm ................1 38........EHVS80-38...................... Spring............................................................ .................................1 39........EHVS80-39A.................... Spacer........................................................... .................................1 40........EHVS80-40...................
Streszczenie treści zawartej na stronie nr. 17
Index Part No. No. Description Size Qty. 109......EHVS80-109.................... Label ............................................................. .................................1 110......EHVS80-110.................... Pan Hand Screw ........................................... 3/16”x3/8” .................3 111......EHVS80-111.................... Extension Cover............................................ .................................1 112......EHVS80-112.................... Washer......
Streszczenie treści zawartej na stronie nr. 18
Stand Assembly Index Part No. No. Description Size Qty. 1..........TS-0680031 ..................... Flat Washer................................................... 5/16”.........................22 2..........TS-0720081 ..................... Lock Washer ................................................. 5/16”.........................10 3..........TS-0561021 ..................... Hex Nut......................................................... 5/16”...........................8 4..........EHVS80CS-S0
Streszczenie treści zawartej na stronie nr. 19
19
