Instrukcja obsługi Vision Fitness X6600HRT/DA

Streszczenie treści zawartej na stronie nr. 1

Assembly
Guide
X6600HRT/DA
DUAL-ACTION ELLIPTICAL TRAINER

Streszczenie treści zawartej na stronie nr. 2

X6600HRT/DA dual-action elliptical trainer To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding though, find your new Elliptical Trainer’s serial number located below the power switch, and enter here: Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardw

Streszczenie treści zawartej na stronie nr. 3

TOOLS & PARTS INCLUDED MM 5 Allen Wrench Screwdriver MM 6 L-Shaped Wrench PARTS BOX Heart Rate Chest Strap, Qty: 1 Power Supply, Qty: 1 Arm Bracket Covers, Qty: 2 Logo Endcaps, Qty: 2 Stabilizers, Qty: 2 Stabilizer Covers, Qty: 2 Water Bottle and Holder, Qty: 1 Console Mast Cover Plate, Qty: 1 Assembly Guide Owner’s Guide Warranty Card Parts Bags Tools

Streszczenie treści zawartej na stronie nr. 4

HARDWARE INCLUDED ORANGE BAG PINK BAG MM M4 x 12 Screw MM M8 x 12 Bolt Quantity: 4 Quantity: 2 M8 Arc Washer Quantity: 4 BLUE BAG M30 Teflon Washer Quantity: 2 MM M4 x 12 Screw Quantity: 4 M20 Spring Washer Quantity: 2 MM M3 x 10 Screw Quantity: 1 M30 Washer Quantity: 2 MM M8 x 75 Bolt Quantity: 2

Streszczenie treści zawartej na stronie nr. 5

STEP 1 ORANGE BAG • Install the left and right stabilizers with the four arc-shaped STEP 1 washers (M8) and four bolts (M8 x MM 20), using the Blue 5 Allen wrench. • Cover both stabilizers with the included rubber boots. STEP 2 BLUE BAG • Slide the console mast cover onto the console mast. STEP 2 • Unfold the console cable and attach it to the string located inside the console mast. Guide the wire up through the mast while simultaneously sliding the console mast onto the frame bracket. • Attach

Streszczenie treści zawartej na stronie nr. 6

STEP 3 PINK BAG • Slide a small spring washer (M20) onto the lower pedal arm support, followed by the right lower arm. Attach with a white Teflon washer (M30), a flat washer (M30), and bolt (M8 x 12), using Blue-han- MM dled 5 Allen wrench. • Pivot the lower arm and insert the top end into the upper handlebar bracket. • Tighten the bottom bolt (M8) on the arm bracket connection block, using the 6mm L-shaped Allen wrench. • Repeat the above steps to attach the arms on the left side. STEP 3 6

Streszczenie treści zawartej na stronie nr. 7

STEP 4 GREEN BAG • Slide right upper arm into right STEP upper handlebar bracket. 4 • Tighten the top bolt (M8) on the arm bracket connection block, using the MM 6 L-shaped Allen wrench. • Attach plastic arm bracket cover to the front of the arm bracket connection block. This is a snap fit. • Attach the plastic logo endcap to the side of the arm bracket connection block. This is a snap fit. • Repeat the above steps on the left side. • Attach water bottle bracket with the included screws. 7

Streszczenie treści zawartej na stronie nr. 8

STEP 5 CONSOLE • Remove the four screws from the back of the console. Plug the wire connectors from inside the mast into the console. The cable connectors are slotted, so do not force the connection. STEP 5 • Mount the console to the mast using the four screws. Do not pinch the cable! 621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 www.visionfitness.com 2001 Vision Fitness. All Rights Reserved. 3.01 P