Streszczenie treści zawartej na stronie nr. 1
DURO® STRIPPER
Operating Manual
Read before use and keep safe
Table of Contents
1.0 Technical Data Page 2
2.0 Safety Page 2
3.0 Safety instructions Page 2
4.0 Maintenance Page 3
5.0 Use Page 4
6.0 Information about various floorings Page 5
7.0 Troubleshooting Page 5
8.0 Spare Parts Page 6
9.0 Schematic Page 8
10.0 Blade Selection Page 10
(800) 624-2408 (530) 626-9386 Fax (53
Streszczenie treści zawartej na stronie nr. 2
1.0 Technical data/technical description Power supply 120V AC Power consumption 2000W, 18A with current limitor Number of strokes 8500 strokes/min Sound pressure level 88 dB(A) Sound energy level 101 dB(A) Hand/Arm-Vibration 16 m/s2 Weight 35 lbs Comes with Duro ® Stripper, 2 rigid blades, safety goggles and tool kit. Case is optional. 2.0 Safety The Sinclair Duro ® Stripper has Class 2 protective insulation. It meets the
Streszczenie treści zawartej na stronie nr. 3
Please make sure any user of the machine is familiar with these instructions before work begins. 3.2 Danger while working with the machine The Duro ® Stripper is designed to the highest technical standards. Incorrect use can be dangerous! Use this machine only: - As instructed in this operating manual. - With the machine in perfect working order. Disturbances that could impair safety have to be eliminated at once. 3.3 Restriction of use The Duro ® Stripper is ex
Streszczenie treści zawartej na stronie nr. 4
5.0 Use Starting Mount the long internal tube with 2 screws to the handle support. Telescope the outer tube over it. The length of the handle may be adjusted by sliding the outer tube. Place the handle into the end of the tube and latch the locking. For your safety the Duro ® Stripper comes with the blade not mounted. Make sure that the power supply is disconnected before mounting the blade. Place the sharp bevel of the blade face up when removing from concrete surface
Streszczenie treści zawartej na stronie nr. 5
6.0 Information about various floorings Main applications of the Duro® Stripper are carpets with foam backing, CV-flooring, PVC-floorings and light carpets. CV-floorings, PVC-floorings and carpets without foam backing Cut strips according to the blade width. Check from time to time if the blade is straight. Carpets with foam backing Use sharp blades only! Remove upper layer with carpet clamp. Remove the foam backing with the stripper. Remove foam across the widt
Streszczenie treści zawartej na stronie nr. 6
8.0 Spare Parts Duro Stripper Schematic # Pieces Description Part # 1 1 Striker Foot Casting D015221 3 1 Blade holder D015223 4 1 Bearing plate D015224 5 1 Drive shaft D015228 6 1 Grip frame D015227 7 1 Hand grip D014916 8 1 Locking flange / Bearing Plate D015233 9 1 Counter Balance Weight D015225 10 1 Crown wheel / Ring Gear D015234 11 4 Rubber bearings D014931 12 1 Fitting spring, 5x 6,5 / Woodruff Key D014905 13 1 Sealing ring / O-Ring D015218
Streszczenie treści zawartej na stronie nr. 7
53 1 Air guide D015200 54 2 Cyl. screw D019523 56 1 Current Limitor T015236 58 1 Motorcase with carbon D015203 59 2 Carbon brush holder D015206 60 2 Carbon brush D014997 61 2 Carbon brush holder cap D015207 62 1 Sealing plate / Handle-Motor Gasket D015208 63 1 PVC Stopper D016086 64 1 On/Off switch D015209 65 2 Lens head screw M4x12 D015210 66 1 Cable clamp D015211 67 1 Handle D015212 68 2 Counter sunk screw M5x50 (Spax) D014796 69 1 Rubber sleeve / Cable Sleeve D015214
Streszczenie treści zawartej na stronie nr. 8
Streszczenie treści zawartej na stronie nr. 9
Streszczenie treści zawartej na stronie nr. 10
TURBO, EXTRO, SUPER, BRAVO, DURO & ECO STRIPPER SUGGESTED BLADE SELECTION BRAVO/DURO/ECO STRIPPER #10-4906 8”Rigid. Our standard blade for removal of vinyl, carpet, adhesive, etc. Bevel edge of blade should be up for concrete and down for wood sub-surfaces. Precutting of carpet and vinyl needed. #10-4904 8”Flexible. Same as above, yet for uneven concrete surfaces and some soft foam back carpet. #10-4907T 8”Tile Blade. For use on VAT and VCT tile. Prevents tile from jamming
Streszczenie treści zawartej na stronie nr. 11
STANDARD WARRANTY SINCLAIR EQUIPMENT COMPANY’S tools are warranted to be free of defects in workmanship and materials for a period of one year from the date of original purchase. Should any trouble develop during this one year period, return the complete tool, freight prepaid, to SINCLAIR’S authorized Service Center. If inspection shows the trouble is caused by defective workmanship or materials, SINCLAIR EQUIPMENT COMPANY will repair, or, at its option, replace without charge.
Streszczenie treści zawartej na stronie nr. 12
NOTES 10
