Streszczenie treści zawartej na stronie nr. 1
72-4131-250
8/03
Dumbo Pylon
Owner’s Manual
© Disney
Streszczenie treści zawartej na stronie nr. 2
Congratulations ongratulations on your purchase of the Lionel Dumbo Pylon! Watch as Dumbo circles the Ctower. Mrs. Jumbo and Timothy Q. Mouse peer out of the illuminated windows at the base of the pylon. Dumbo Pylon Inventory • Pylon •Two green wires • Dumbo figure • Owner’s Manual • Support arm • Service Center list • Switch Table of contents Wiring your Dumbo Pylon with a conventional power supply 3-4 Installing your Dumbo Pylon 5 Attaching the figure to your Dumbo Pylon 6 Operating your Dumbo
Streszczenie treści zawartej na stronie nr. 3
Wiring your Dumbo Pylon with a conventional power supply iring your accessory is the first step in preparing for flight. The Dumbo Pylon will Woperate best at 12-18 volts (AC), and it can be powered through track power with a Lionel Lockon (available separately, 6-62900), or a FasTrack Accessory Power Wire (available separately, 6-12053), OR through an accessory power supply. We recommend that you choose a power supply that will allow you to increase or decrease the voltage to the accessory. Cha
Streszczenie treści zawartej na stronie nr. 4
A U U A Wiring your Dumbo Pylon with a conventional power supply (continued) Mounting holes Mounting holes UA POWER SUPPLY FasTrack Accessory Power Wire Figure 1. Wiring for conventional operation 4
Streszczenie treści zawartej na stronie nr. 5
Installing your Dumbo Pylon hoose a flat, level area on your layout for the accessory. Secure this accessory to your Clayout with four screws (not included) using the holes near the corners of the base. Be sure to wire your accessory before you secure it to your layout—the wire terminals are on the underside of the base. Keep in mind that Dumbo flies in a circle with diameter of 30”. The flight path must be kept clear. 5
Streszczenie treści zawartej na stronie nr. 6
Attaching the figure to your Dumbo Pylon omplete the assembly of your Dumbo Pylon by attaching the Dumbo figure and support Crods to the structure. Figure 2 illustrates the following procedure. 1. Note that the supporting rod has different shaped ends. Insert the flattened end of the support rods into the tube protruding from the top of the pylon. Refer to the diagram for further assistance. 2. Insert the D-shaped ends of the wires into the openings in the bottom of the Dumbo figure. Support ro
Streszczenie treści zawartej na stronie nr. 7
Operating your Dumbo Pylon with TrainMaster Command Control ou may choose to wire your accessory with an SC-2 Switch and Accessory Controller Y(available separately, 6-22980) or the Accessory Switch Controller (available separately, 6-14182). Refer to these manuals for additional information. SC-2 wiring and operation Three wires (not included) are needed to connect your Pylon to the SC-2 and a separate accessory transformer. We recommend using 22 gauge wire. Refer to Figure 3. 1. Attach one wi
Streszczenie treści zawartej na stronie nr. 8
Operating your Dumbo Pylon with TrainMaster Command Control (continued) Accessory Switch Controller wiring and operation Three wires (not included) are needed to connect your Pylon to the Accessory Switch Controller (ASC) and a separate accessory transformer. Refer to Figure 4. 1. Attach one wire to the transformer Power/A terminal and connect it to the COMM terminal on the ASC. 2. Connect one of the Pylon terminals to a numbered accessory terminal on the ASC. 3. Finally, connect the remaining
Streszczenie treści zawartej na stronie nr. 9
Replacing the lamp in your Dumbo Pylon our Pylon is illuminated by one 18-volt lamp. During the course of normal operations, Y this lamp may require replacement. Follow these steps to replace the lamp with Lionel part no. 612-3011-311. 1. Lift the support arm out of the tubes at the top of the pylon. Also, remove any screws securing the base to your layout. 2. Remove the four base screws from the underside of the base with a small Phillips-head screwdriver and lift away the roof and pylon tower
Streszczenie treści zawartej na stronie nr. 10
Replacing the lamp on your Dumbo Pylon (continued) Base of the Pylon Mounting holes Roof Base screws screws (recessed) (recessed) Mounting holes Figure 5. Screw locations 10
Streszczenie treści zawartej na stronie nr. 11
Replacing the lamp on your Dumbo Pylon (continued) Interior of the building with the roof removed Figure 6. Lamp location 11
Streszczenie treści zawartej na stronie nr. 12
Limited Warranty/Lionel Service his Lionel product, including all mechanical and electrical components, moving parts, motors and T structural components, except for light bulbs, is warranted to the original consumer-purchaser, for one year against original defects in materials or workmanship when purchased through an authorized Lionel merchant. This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of commercial use, or damage resulting from abuse or misu
