Streszczenie treści zawartej na stronie nr. 1
Accessory Application Publications No.
AII 20469
2000 CIVIC
INSTALLATION
SECURITY SYSTEM
4-DOOR Issue Date
INSTRUCTIONS (LX/EX/VP MODELS ONLY)
AUG 1999
PARTS LIST Remote Transmitter (sold separately):
P/N 08E61-S01-101
Security System (sold separately):
(Required for LX model only)
P/N 08E51-S01-101F
2 T ransmitters
Control unit
Owner’s Manual
Owner’s Manual
(discard)
Security Attachment (sold separately):
2 Washer-screws
P/N 08E55-S01-100H
(not used)
Control unit bracket
Relay 4-pin
Relay
Streszczenie treści zawartej na stronie nr. 2
3-Pin connector INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, Nut equipment, and training to correctly and safely add equipment to your car. These procedures should not Washer be attempted by “do-it-yourselfers.” NOTE: The Owner’s Manual included with the Security Owner’s Manual Attachment should be placed in the glove box for future reference. The Owner’s Manual included with the Sec
Streszczenie treści zawartej na stronie nr. 3
4. Remove the driver's dashboard lower cover: 6. Remove the left kick panel (two clips, and slide back while pulling its lower end inside). Remove the three screws. Gently pull along the top to release the three retaining clips. Unplug the connector(s) and remove the cover. RETAINING CLIP CLIP (LARGE) CLIP LOWER END LEFT KICK PANEL 7. Remove the upper steering column cover (three screws and six clips). SELF-TAPPING SCREW UPPER STEERING COLUMN COVER DRIVER'S DASHBOARD LOWER COVER MOONROOF M
Streszczenie treści zawartej na stronie nr. 4
Intalling the LED 11. Carefully push the LED terminals into the 2-pin connector from the kit. 8. Measure and mark the upper steering column cover removed in step 7, and lightly center-punch the LOCK mark. Insert the tabs into the grooves, slide the lock Insert. toward the front, and press 9. While wearing eye protection, drill a 5.5 mm hole down on the end. through the center-punched mark. Remove all burrs. 5.5 mm DRILL WHITE WIRE CENTER OF 2-PIN COLUMN COVER CONNECTOR Firmly push the terminal
Streszczenie treści zawartej na stronie nr. 5
13. Route the terminal ends of the disarm switch Installing the Control Unit harness through the 12 mm hole you just drilled in 16. Loosen the bolt on the right of the steering shaft, the dashboard lower cover. Secure the disarm switch then slide the slot of the control bracket under the on the dashboard lower cover using the 12 mm and head of the bolt you just loosened. washer provided. Tighten the nut securely. CONTROL BRACKET INTERLOCK CONTROL UNIT (A/T Model only) 6 x 12 mm FLANGE BOLT 12 mm
Streszczenie treści zawartej na stronie nr. 6
18. Position the control unit on the control bracket, and 20. Remove number 3 fuse from the bottom row of the install the two collars and two 4 x 30 mm bolts. fuse box. CONTROL UNIT BLUE TAPE (Remove.) COLLARS FUSE BOX 4 x 30 mm BOLTS (Discard.) 22-PIN CONNECTOR 19. Locate the 22-pin connector blue-taped to the vehicle harness, and remove the blue tape to free 21. Push the two fuses from the kit into the number 3 the connector. Plug the 22-pin connector you just and number 6 slots in the fuse bo
Streszczenie treści zawartej na stronie nr. 7
23. Locate the 4-pin and 6-pin connectors blue-taped to 26. Install the upper steering column cover. Locate the vehicle harness behind the fuse box. the 2-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Get the resistor supplied with the attachment kit, plug one end of the resistor into the 2-pin connector you just freed and the other end into the 2-pin connector from the LED. UPPER STEERING 4-PIN AND 6-PIN COLUMN COVER CONNECTORS LED 2-PIN CONNEC
Streszczenie treści zawartej na stronie nr. 8
29. Behind the left side of the fuse box, locate the 3-pin INSPECTION connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Plug the 31. Check that all wire harnesses are routed properly 3-pin connector you just freed into the 3-pin and all connectors are plugged in. connector from the disarm switch. 32. Reinstall all removed parts. 33. Connect the negative cable to the battery. 34. Check operation of the Security System according VEHICLE HARNESS 3-PIN CONN
