Instrukcja obsługi Clifford Tazor II

Streszczenie treści zawartej na stronie nr. 1

TM
World-Class Auto Security
II
Owner's Manual
The keychain remote controls are the keys to your TAZOR system. If you
need additional remote controls for other drivers of the vehicle, see your
local Authorized Clifford Dealer or call the Clifford Customer Service
Department toll-free at (8OO) 824-32O8 .

Streszczenie treści zawartej na stronie nr. 2

Standard Features of the Tazor II ✔ Lifetime Warranty — For as long as you own the vehicle. ✔ FACT™—False Alarm Control and Test — One of many patented Clifford innovations, FACT absolutely, positively ends recurring false alarms. ✔ A Pair of 2-Button/3-Channel Remote Controls — Fingertip command from a typical range of 100 feet. ✔ AntiScan™—Blocks the digital code scanners still used by some thieves. ✔ Anti-CodeGrabbing™ (ACG) Capability— A code-grabber is a new device that lets a thief record

Streszczenie treści zawartej na stronie nr. 3

Standard Features of the Tazor II (cont.) ✔ Patented Malfunction AutoBypass™ —In the unlikely event of a trigger or sensor malfunction, your Tazor II will automatically bypass the malfunction and arm all other points to continue relentless protection of your vehicle. ✔ TotalRecall™ — Tazor II’s non-volatile memory automatically stores the identity of the last activated trigger or sensor activated while the system was armed. ✔ User-Selectable AutoArming™— Automatically arms itself “passively” if

Streszczenie treści zawartej na stronie nr. 4

Your 2-button/3-channel remote controls The 2-button/3-channel remote controls are miniature radio transmitters powered by a 12-volt batteries. Range is up to 100 feet (a weak remote control battery will reduce range). The remote control is the key to your system. You will use it to arm and disarm the system, lock* and unlock* the doors, activate the panic feature, command options such as a remote trunk release, power window operation, or other accessory. TO ARM Press button I once. You will hea

Streszczenie treści zawartej na stronie nr. 5

Valet mode Whenever the system is put in valet mode, all of the system’s security features are switched off. At various times, you will need to turn the system off. For instance, when having your car serviced, washed or parked by a valet. NOTE: If you temporarily lose the use of your remote controls, you can disarm the system by enabling valet mode. To enable valet mode 1. Turn the ignition switch to its “ON” position or start the engine. 2. Flip the valet switch. The system’s LED will glow con

Streszczenie treści zawartej na stronie nr. 6

Automatic malfunction bypass The system automatically bypasses any faulty point and arms all other triggers and sensors to provide the utmost protection until you can have the system serviced. Prior intrusion attempt alert If you hear three chirps when you remotely disarm, the alarm sounded in your absence. FACT™— False Alarm Control and Test With FACT, you’ll never experience repeated false alarms. If the siren goes off, DO NOT remotely disarm the system; allow it to run for the full 30 second

Streszczenie treści zawartej na stronie nr. 7

User-selectable features Your Tazor II vehicle security system allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just flick the valet switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below. To change any of the settings, use the following procedure. To restore the feature to its factory setting, just repeat the procedure: 1. Select t

Streszczenie treści zawartej na stronie nr. 8

Example : To change the AutoArming feature from its factory setting of “on” to “off,” you would do the following: • Turn the ignition key to the ON position. • Flick the valet switch back and forth 4 times (you’ll hear a chirp each time to help you count to the total of 4 chirps). • Wait 3 seconds. The system will sound one more chirp to confirm that the AutoArming setting is now off (1 chirp = off, 2 chirps = on). • Turn the ignition off. That’s all there is to it! To change the Adding new remo