Streszczenie treści zawartej na stronie nr. 1
High End Residential
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-334-9111
Hydra-Rib Internet Address: http://www.hydra-rib.com
Spalding Internet Address: http://www.spalding
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL SAFETY INSTRUCTIONS WARNING FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN Read and understand warnings listed SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. below before using this product. Owner must ensure that all players know and Failure to follow these warnings may follow these rules for safe operation of the system. result in serious injury and/or property damage. To ensure safety, do not at
Streszczenie treści zawartej na stronie nr. 3
PARTS LIST Item Qty. Part No. Description 1 1 958860 Pole 2 1 958850 Plate, Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, 3/8 Locking, .380 I.D., .63 O.D. 7 2 250001 Bolt, Hex, Tap, 3/8-16 x 4” Long 8 2* 250002 Bolt, Hex, Tap, 3/8-16 x 2” Long 9 1 203457 Label, Logo, Vinyl, 2.3” x 2.7” 10 1 Backboard ID# 516000 06/05 11 1 516000 Label, Height Adjustment 12 1 204940 Screw Jack 11 13 2 220563 Screw, 1/4-20 x 1/2” Long, Rim Cover 14 1 80854501 Rod, Thread
Streszczenie treści zawartej na stronie nr. 4
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (1)* Item #20 (1) Item #8 (2*) Item #7 (2) Item #13 (2) Item #29 (4) Item #34 (4) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) Item #28 (3) Item #6 (4) Item #33 (2)* Item #27 (4)* Item #21 (16) Item #24 (9) Item #5 (4) Item #22 (9)* Item #25 (12) Item #26 (1) HARDWARE IDENTIFIER (OTHER - NOT ACTUAL SIZE) Item #37 (1) Item #35 (1) Item #38 (14) Item #39 (4) Item #40 (8) Item #36 (1) ID# M8672412 10/05 4
Streszczenie treści zawartej na stronie nr. 5
Ensure ground is level with playing surface, then dig pole hole. 1. 24" (61 cm) 48" (121.9 cm) WARNING! 24" (61 cm) GROUND SURFACE PLAYING SURFACE 48" (121.9 cm) CONTACT UTILITIES BEFORE DIGGING. 2. Install nut (25) to J-bolt (19) as shown. Repeat procedure for 25 25 remaining three J-bolts (19). 2.75” 2 (7 cm) IMPORTANT! 19 25 Make sure nuts (25) are 2.75” (7 cm) from top of J-bolts Install threaded ends of J-bolts (19) through holes 3. in mounting plate (2) and secure as shown. 19 NOTE: Make
Streszczenie treści zawartej na stronie nr. 6
Fill hole with concrete. Tamp down concrete to release air pockets 4. and build drainage hill. DRAINAGE HILL 1" (2.54 cm) PLAYING SURFACE SIDE VIEW Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to release 5. any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate a
Streszczenie treści zawartej na stronie nr. 7
Insert bushings (38, 39, and 40) into 6. areas shown. 40 38 10 40 40 38 40 40 38 40 40 40 40 IMPORTANT! 38 Bushing types are 38 identified 38 with a letter. 1 38 17 39 39 38 39 38 18 39 39 38 10/05 ID# M8672412 7
Streszczenie treści zawartej na stronie nr. 8
Rest top of pole (1) on a piece of scrap wood (not included) and line up holes in pole to holes in 7A. mounting plate (2) as shown. 1 WARNING! PLAYING SURFACE THREE PEOPLE SCRAP WOOD REQUIRED FOR THIS (NOT INCLUDED) PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY 1 DAMAGE. 2 PLAYING SURFACE Insert bolt (28) through holes in plate and pole and secure with nut (22). 7B. 1 28 22 ID# M8672412 10/05 8
Streszczenie treści zawartej na stronie nr. 9
8. WARNING! TWO people are required to lift pole into position so that the threaded assembly rod (14) can be installed and secured by the THIRD person. THREE PEOPLE While pole is being supported by TWO REQUIRED FOR THIS capable adults, position rod (14) and lock PROCEDURE. FAILURE into place with hitch pin (36) and cotter TO FOLLOW THIS WARNING COULD RESULT pin (37). IN SERIOUS INJURY AND/OR PROPERTY Slide barrel washer (35) onto other end of DAMAGE. rod (14) and secure with washer (24) and n
Streszczenie treści zawartej na stronie nr. 10
9. While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 21 17 18 21 28 ID# M8672412 10/05 10
Streszczenie treści zawartej na stronie nr. 11
Attach elevator adjustment (12) to 10. lower yoke (18). WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 38 22 18 21 38 12 38 21 20 10/05 ID# M8672412 11
Streszczenie treści zawartej na stronie nr. 12
Attach elevator adjustment (12) to pole bracket. 11. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 21 21 23 22 33 33 12 ID# M8672412 10/05 12
Streszczenie treści zawartej na stronie nr. 13
Attach backboard (10) to upper and lower 12. yokes (18 & 17). Then, hinge board to match up with holes in A. B. First attach board (10) to upper yoke (17), lower yoke (18), FIG. C, and secure with using TWO people to hold the board and hardware as shown in FIG. D. ONE person to attach hardware (FIG. A). Use hardware as shown in FIG. B. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. FIG. A FIG. C FIG. D 1
Streszczenie treści zawartej na stronie nr. 14
Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” from 13. the end of the rod (14) as shown (Figure A). Remove rim cover (16), attach rim assembly (3) to backboard (10) and reattach rim cover (16). ** For rim assembly see instructions included with rim. IMPORTANT! Carefully cut and peel protective film away from board prior to attaching rim. 14 26 FIGURE A. 5 6 10 Rim Assembly 16 3 Refer To Instructions 27 Included With Rim 27 Hardware For Rim Assembly. 8 7 ID# M86724
Streszczenie treści zawartej na stronie nr. 15
10 9 87 10 9 87 10 9 87 10 9 87 10 9 87 10 9 87 10 9 87 10 9 87 14. Set-up For Left Side Set-up For Right Side Apply height indicator A. 30 30 labels (32 & 31) to height 10 9 8 7 indicators (30). 10 10 9 7 9 8 7 8 10 9 8 7 10 7 8 9 31 10 10 32 7 9 8 9 8 7 10 7 8 9 Attach height indicators to lower yoke in area shown by turning B. screws (29) into place with a phillips-head screwdriver. Apply name plate sticker (15) to lower yoke as shown. IMPORTANT! 10 7 9 8 29 NOTE ORIENTATION 10 OF HEIGHT 7 8
Streszczenie treści zawartej na stronie nr. 16
16. Upright pole (1) by tightening nut (26). WARNING! Using 15/16” wrench, turn nut (26) clockwise to begin standing pole upright. Continue to turn nut (26) THREE PEOPLE REQUIRED FOR THIS PROCEDURE.: TWO PEOPLE ARE REQUIRED TO until pole has come to rest against washers (24) and GUIDE AND SUPPORT THE SYSTEM WHILE THE pole is vertical. THIRD PERSON IS TIGHTENING NUT (26) TO RAISE THE SYSTEM UPRIGHT. Once pole is in its final position, install washers (24) FAILURE TO FOLLOW THIS WARNING COULD an
Streszczenie treści zawartej na stronie nr. 17
After pole has been secured to the anchor plate (2) loosen nut (26), 17. remove cotter pin (37), and pull out pin (36). This will allow the removal of the threaded assembly rod (14) which is no longer necessary for the remainder of the assembly and installation of system. WARNING! ONLY AFTER THE ANCHOR PLATE HAS BEEN FULLY TIGHTENED: Remove cotter pin (37) and pin (36) to threaded assembly remove rod (14) from anchor plate (2). 26 24 35 14 37 36 25 24 25 10/05 ID# M8672412 17
Streszczenie treści zawartej na stronie nr. 18
Check system leveling. Pole (1) 18. should be level in all directions. After system is leveled, completely tighten all nuts (25). NOTE: If adjustment is necessary, adjust system by rotating 1 the nuts (25) between anchor plate (2) and pole flange. 25 2 Apply height adjust ment label (11). 19. Adjust system by turning crank until desired height is reached per height indicator (30). 30 WARNING! 12 10 feet (3.05 m) 11 READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT. F
Streszczenie treści zawartej na stronie nr. 19
LIMITED LIFETIME WARRANTY ® Subject to proper installation and normal use, Hydra-Rib warrants, subject to limitations below, to the original retail ® purchaser all structural components of the Hydra-Rib system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Merchandise must be shipped prepaid with a copy of proof of purchase to our factory for examination to see whether it needs to be repaired or replaced. Any labor costs, travel