Streszczenie treści zawartej na stronie nr. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY DIAMOND ELITE
Safety Notice
OLYMPIC BENCH
Hardware Identifier
MD-857
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-857
Retain This
Manual for
Reference
08-05-09
OWNER'S
MANUAL
®
IMPEX INC.
2801 S. Towne Ave., Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.co
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 EXPLODED DIAGRAM…………………………………………………………………….. 11 PARTS L
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at
Streszczenie treści zawartej na stronie nr. 4
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown 3
Streszczenie treści zawartej na stronie nr. 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
Streszczenie treści zawartej na stronie nr. 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
Streszczenie treści zawartej na stronie nr. 7
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Upright Beam (#1) to a Rear Stabilizer (#3). Secure it with two M10 x 5/8” Allen Bolts (#63), and two Ø ¾” Washers (#66). C.) Attach the bottom of the Rear Diagona
Streszczenie treści zawartej na stronie nr. 8
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Leg Developer Support (#13) to the Front Stabilizer (#14). Secure it with three M10 x 5/8” Allen Bolts (#63) and ¾” Washers (#66). C.) Slide the Sliding Block (#15) onto the Main Seat Support (#4). Thread a M18 Lock Knob (#42) into the selected hole to hold the Sliding Block in position. D.) Attach the Main Seat Support (#4) to the Leg Developer Support (#13). Secure it with one M10 x 2
Streszczenie treści zawartej na stronie nr. 9
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the Backrest Supports (#21) to the long pivot on the Sliding Block (#15). Attach the Backrest Board (#26) to the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#65) and Ø5/8” Washers (#67). Place the Backrest Board against the Backrest Adjustment Bar. B.) Attach the Seat Bracket (#20) to the short pivot on the Sliding Block. Secure it with one M10 x 4 ¾” Allen Bolt (#61), two Ø ¾” Washers (#66), and one M10 Ai
Streszczenie treści zawartej na stronie nr. 10
STEP 4 (See Diagram 4) A.) Insert the U-shaped Pin (#49) into the open slot on the Leg Developer Support (#13). Secure it with one M6 x ½” Philips Screw (#47), Ø ½” Washer (#48), and Spring (#50). B.) Attach the Leg Developer (#10) to the Leg Developer Support. Secure it with an Axle (#55), two M10 x 5/8” Allen Bolts (#63) and two ¾” Washers (#66). C.) Insert one Foam Tube (#22) halfway through the hole on the Leg Developer Holder. Insert two Foam Tubes halfway through the holes on t
Streszczenie treści zawartej na stronie nr. 11
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#28) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Allen Bolts (#64) and Ø 5/8” Washers (#67). B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Support. Use a M18 Lock Knob (#42) to secure the Stand. C.) Attach the Curl Bar Handle Support (#11) to the bracket on the Leg Developer (#10). Secure it with a 3 7/8” Lock Pin (#52). The Leg Developer can be locked when doing Sit Up exercises. Simply pull th
Streszczenie treści zawartej na stronie nr. 12
11
Streszczenie treści zawartej na stronie nr. 13
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Upright Beam 1 51 4 ½” L-shaped Pin 2 2 Right Upright Beam 1 52 3 7/8” Lock Pin 1 3 Rear Stabilizer 2 53 4” L-shaped Pin 1 4 Main Seat Support 1 54 Spring Clip 1 5 Cross Brace 1 55 Axle 1 6 Backrest Adjustment Bar 1 56 M10 x 3 ½” Carriage Bolt 4 7 Squat Bar Catch 2 57 M10 x 2 ¾” Carriage Bolt 2 8 Rear Diagonal Support 2 58 M10 x 2 ½” Carriage Bolt 1 9 Arm Curl Stand 1 59 M10 x 2 3/8” Carriage Bolt 2 10 Leg Developer 1 6
Streszczenie treści zawartej na stronie nr. 14
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling I
