Streszczenie treści zawartej na stronie nr. 1
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it
contains important information about your model.
Write Model Number From
REQUIRED TOOLS AND MATERIALS:
Box Here:
• Garden Hose or Sand
• Two (2) Capable Adults • (2 each) Wrenches
• Tape Measure
1/2" 9/16" 3/4"
AND/OR
• Wood Board (scrap) (2) Socke
Streszczenie treści zawartej na stronie nr. 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. NOTE: Not all items pictured are included with every model. 2 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 3
WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. � DO NOT HANG on the rim or any part of the system including backboard, support braces or net. � During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury co
Streszczenie treści zawartej na stronie nr. 4
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Streszczenie treści zawartej na stronie nr. 5
NOTICE TO ASSEMBLERS Adult Assembly Required. Dispose of ALL packaging materials promptly. As with all products, periodically inspect for loose small parts. Assembled unit MUST be filled with sand or water at ALL times. ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift support system. IMPORTANT! Remove all contents from b
Streszczenie treści zawartej na stronie nr. 6
Get to know the basic parts of your basketball system... BACKBOARD RIM ELEVATOR SYSTEM POLE FRONT PANEL BASE 6 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 7
PARTS LIST - See Hardware Identifier Item Qty. Part No. Description Item Qty. Part No. Description 1 1 266000 Base 36 2 201682 Spacer, .530 I.D. x 1.875 2 2 908184 Strut, Pole to Base 37 2 900867 Plate, Triangle, (Black) 3 1 804833 Exacta Height Assembly 38 1 207103 Cap, Pole Top 4 1 FR908006 Top Pole Section 39 2 200520 Screw, #8 x 3/4 Long 5 1 FR918107 Middle Pole Section 40 1 202605 Bolt, Hex, 1/2-13 x 4.25 Long 6 1 FR908179 Bottom Pole Section 41 1 700012 Cap, Base 7 2 108183 Wheel Bracket
Streszczenie treści zawartej na stronie nr. 8
HARDWARE IDENTIFIER (BOLTS & SCREWS) #16 (2) #18 (2) #29 (6) #39 (2) Item #23 (1)* #47 (6) #44 (4)* #50 (2) #63 (6) #52 (4) #19 (2) #48 (2) #40 (1) #12 (1) #55 (1) * You may have extra parts with this model. 8 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 9
HARDWARE IDENTIFIER (NUTS & WASHERS) #11 (6) #10 (1) #14 (13)* #31 (7) #17 (4) #45 (4)* #51 (6) #58 (1) #64 (6) #59 (1) HARDWARE IDENTIFIER (STEEL SPACERS) #9 (2) #21 (2) 9 01/07 ID# M6611043
Streszczenie treści zawartej na stronie nr. 10
HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS) #53 (1) #30 (4) #13 (4) #67 (1) #26 (4) #20 (2) #36 (2) HARDWARE IDENTIFIER (OTHER) #57 (1) #66 (1) #54 (1) #56 (1) 10 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 11
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section. TOOLS REQUIRED FOR THIS SECTION (2 each) Wrenches (2) Socket Wrenches 1/2” and 9/16” and Sockets And/Or: 1/2” 9/16” Extension Phillips-Head Screwdriver 11 01/07 ID# M6611043
Streszczenie treści zawartej na stronie nr. 12
1. Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolts P/N 203103. 3 Label,Height Indicator P/N 204872 Height Adjustment Rod P/N 904833 Label,Height Indicator P/N 204872 Handle, Right P/N 204856 Nut P/N 203100 Carriage Bolt P/N 203103 Screw P/N 204803 Nut P/N 203100 Carriage Bolt P/N 203103 Handle, Left P/N 204855 12 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 13
Complete wheel assembly as shown in Figure A. Secure wheel bracket (7), wheel (8), axle (9), and push 2. nuts (13) to the tank (1) with a single bolt (18) and washer (51). Repeat procedure for opposite wheel. NOTE: Do not install both bolts into the wheel assembly at this time. The front bolt will be installed during strut assembly in Step 3 of 1 this section 18 51 NOTE: TO INSTALL SECOND 7 PUSHNUT: 13 9 • Assemble Pushnut, Wheels, Axle, And Wheel 8 Bracket As Shown. 13 • Support Pushnut/Axl
Streszczenie treści zawartej na stronie nr. 14
Identify pole sections. 3. 5 Identification Sticker 6 4 While maintaining alignment, bounce middle pole section (5) into top section (4) 4. using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. CAUTION! IMPORTANT! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY Align dimple of top pole section (4) POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE into trough of middle pole section (5) A 3-1/2" MI
Streszczenie treści zawartej na stronie nr. 15
Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a 5. wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT! Align dimple of middle pole section (5) into trough of bottom pole section (6) CAUTION! as shown. THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-
Streszczenie treści zawartej na stronie nr. 16
6. Attach pole assembly to base (1) as shown. Secure pole assembly to tank using bolts (50) and pole mounting bracket (49) as shown. 6 WARNING! 6 TWO PEOPLE REQUIRED 49 1 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS 50 INJURY AND/OR PROPERTY DAMAGE. 49 50 Secure tank struts (2) to pole as shown. Place cover (53) over exposed end of bolt 7. as shown. 53 51 IMPORTANT! 10 DO NOT TIGHTEN 12 COMPLETELY 51 2 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO
Streszczenie treści zawartej na stronie nr. 17
Rotate non-secured ends of tank struts (2) outward to mounting holes in tank as 8. shown. Secure ends of tank struts (2) to wheel bracket (7), as shown. Repeat for opposite side. IMPORTANT! DO NOT TIGHTEN COMPLETELY WARNING! 2 48 2 51 TWO PEOPLE REQUIRED 48 FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS 51 INJURY AND/OR PROPERTY DAMAGE. 7 9. Secure cover (28) to tank struts (2) using bolts (47) and nuts (14) as shown. 28 IMPORTANT! TIGHTEN ALL COMPONENTS COMPLETEL
Streszczenie treści zawartej na stronie nr. 18
10. Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) as shown. Tighten flange nuts (14) completely. 14 15 14 42 16 16 4 Attach spacers (20, 21) to pole mount bracket (15) with 11. bolts (19), washers (17), and nuts (11) as shown. IMPORTANT! 15 Tighten just until 17 11 washers (17) stop 17 moving. 17 17 20 19 21 21 20 18 ID# M6611043 01/07
Streszczenie treści zawartej na stronie nr. 19
12. Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. FIG. A 14 22 15 22 25 23 IMPORTANT! 24 23 Loop end of pin lanyard (25) over 25 carriage bolt (23) 25 as it passes through the pole 24 mount bracket (15) during this 24 assembly. 13. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (24). 24 19 01/07 ID# M6611043
Streszczenie treści zawartej na stronie nr. 20
SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section. TOOLS REQUIRED FOR THIS SECTION Wrenches (2 each) (2) Socket Wrenches and Sockets 1/2”, 9/16”, and 3/4” And/Or 1/2” 9/16” 3/4” Extension Phillips-Head Screwdriver Sawhorse Identify elevator tubes. Upper Elevator tube 35 TOWARDS BOARD TOWARDS POLE Lower Elevator tube 32 20 ID# M6611043 01/07
