Streszczenie treści zawartej na stronie nr. 19
Assemble backboard brackets (27) using bolts (43), and nuts (8) as shown. 1. 8 8 43 43 27 19 07/05 ID# M671111
Streszczenie treści zawartej na stronie nr. 20
Attach lower elevator tubes (32) and counter balance springs (33) to backboard 2. support brackets (27) using spacers (26), bolt (29), and nut (31) as shown. 11 14 27 26 31 26 29 33 32 48 49 48 44 20 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 1
A DIVISION OF RUSSELL CORPORATION
Portable System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
From Box Here:
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Garden Hose or Sand
• 2 People • (2 each) Wrenches
7/16" 1/2" 9/16" 3/4"
• Tape Measure
AND/OR
• Wood Board (scrap) (2) Socket Wrenches and Sockets
• Sawhorse or Support Table
READ AND UNDERSTAND
• Optional: Large & Small
OPERATOR'S MANUAL
7/16" 1/2" 9/16" 3/4" Adjustable
Streszczenie treści zawartej na stronie nr. 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. NOTE: Not all items pictured are included with every model. 2 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 3
WARNING Read and understand warnings listed below before using this product. Failure to follow these warnings may result in serious injury and/or property damage. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury co
Streszczenie treści zawartej na stronie nr. 4
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify
Streszczenie treści zawartej na stronie nr. 5
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration fo
Streszczenie treści zawartej na stronie nr. 6
Get to know the basic parts of your basketball system..... FRONT BACKBOARD RIM POLE FRONT PANEL BASE 6 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 7
PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 1 1 203470 Washer, Flat, 1.5” O.D. 27 2 908256 Bracket, Backboard Support 2 1 806620 Base Assembly 28 2 200874 Spacer, Steel .402 I.D. x .5 O.D. x 1.5 Long 3 1 804833 Exacta Height Assembly 29 6 206244 Bolt, Hex Head, 1/2-13 x 8 Long 4 1 908006 Top Pole Section 30 4 201642 Spacer, Plastic, .530 I.D. x .625 Long 5 1 90810701 Middle Pole Section 31 7 206340 Lock Nut, Hex Head, 1/2-13 6 1 908142 Bo
Streszczenie treści zawartej na stronie nr. 8
HARDWARE IDENTIFIER (BOLTS & SCREWS) #29 (6) #16 (2) #7 (2) Item #23 (1) #19 (4) #47 (4) #40 (1) #39 (2) #49 (1) #12 (1) #44 (4)* HARDWARE IDENTIFIER (STEEL SPACERS) #21 (2) #28 (2) * You may have extra parts with this model. 8 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 9
HARDWARE IDENTIFIER (NUTS & WASHERS) #18 (4)* #52 (1) #31 (7) #17 (4) #10 (1) #8 (8) #14 (11)* #45 (6) #1 (1) HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS) #30 (4) #26 (4) #20 (2) #36 (2) #11(4)* #13 (2) HARDWARE IDENTIFIER (OTHER) #48 (1) #50 (1) #51 (1) 9 07/05 ID# M671111
Streszczenie treści zawartej na stronie nr. 10
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION Wrenches Phillips-Head (2) 1/2” Screwdriver (2) 3/4” And/Or: (2) Socket Wrenches and Sockets 1/2” 9/16” Extension 10 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 11
Check the following pre-assembled base areas for tightness: Eye bolts P/N 1A. 203452, Washer P/N 203218, Nut P/N 203100, Carriage Bolts P/N 203223 . Carriage Bolts P/N 203223 Front Cover P/N 206002 Pole Bracket P/N 201581 Washer Nut P/N 203218 P/N 203100 Washer P/N 203218 Hex Flange Nut Eye bolts P/N 203452 P/N 203100 Base P/N 206620 11 07/05 ID# M671111
Streszczenie treści zawartej na stronie nr. 12
Check the following pre-assembled handle areas for tightness: Screw P/N 204803, 1B. Nut P/N 203100, Carriage Bolts P/N 203103 . Label,Height Indicator P/N 204872 Height Adjustment Rod P/N 904833 Label,Height Indicator P/N 204872 Handle, Right P/N 204856 Nut P/N 203100 Carriage Bolt P/N 203103 Screw P/N 204803 Nut P/N 203100 Carriage Bolt P/N 203103 Handle, Left P/N 204855 12 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 13
Identify pole sections. 2. 5 Identification Sticker 6 4 TROUGH While maintaining alignment, bounce middle pole section (5) into top section (4) 3. using a wood scrap as shown until the top pole no longer moves toward the pole TROUGH identification sticker on the middle pole. CAUTION! THE IDENTIFICATION STICKER IS IMPORTANT!: LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY Align dimple of top pole section (4) POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" into trough of middle pole
Streszczenie treści zawartej na stronie nr. 14
TROUGH TROUGH Bounce top and middle pole assembly (4 & 5) onto bottom pole section (6) using a 4. wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. IMPORTANT!: Align dimple of middle pole section (5) into trough of bottom pole section (6) TROUGH CAUTION! as shown. THE IDENTIFICATION STICKER IS TROUGH LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2"
Streszczenie treści zawartej na stronie nr. 15
5. 6 Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut 10 12 should be tightened until flush (even) with locknuts outer edge. 6 6. Install rod (9) through bottom pole 7 section (6) as 7 shown. Install large eye bolts (7) onto 9 rod (9) as shown. 9 7. 13 8 45 Secure cover to rod (9) using washers (45) nuts (8) and nut covers (13) as shown. 15 07/05 ID# M671111
Streszczenie treści zawartej na stronie nr. 16
Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts 8. (16) as shown. Tighten flange nuts (14) completely. 16 15 16 42 14 14 4 Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), 9. and nuts (8) as shown. IMPORTANT!: Tighten just until 15 washers (17) stop 17 moving. 8 17 17 17 20 19 21 21 20 16 ID# M671111 07/05
Streszczenie treści zawartej na stronie nr. 17
Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto 10. pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. FIG. A 14 22 15 22 25 23 IMPORTANT!: 24 23 Loop end of pin lanyard (25) over 25 carriage bolt (23) 25 as it passes through the pole 24 mount bracket (15) during this 24 assembly. 11. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) 24 mark with pin (24). 17 07/05 ID# M671111
Streszczenie treści zawartej na stronie nr. 18
SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION Wrenches (2) 1/2" (2) 9/16” (2) 3/4” Phillips- Head And/Or Screwdriver (2) Socket Wrenches and Sockets au in te 1/2” 9/16” Sawhorse 3/4” Extension Identify Upper Elevator tube 35 elevator tubes. Lower Elevator tube 32 18 ID# M671111 07/05
