Streszczenie treści zawartej na stronie nr. 1
TABLE OF CONTENTS
INTRODUCTION 3
STANDARD PACKAGE CONTENTS 3
BEFORE YOU BEGIN 4
PRODUCT OVERVIEW 5
REMOTE TEMPERATURE & HUMIDITY SENSOR 5
MAIN UNIT 7
WEATHER FORECAST 14
PRESSURE HISTORY CHART 14
MOON PHASE ICONS 15
PRESSURE MODE 15
REMOTE AND INDOOR TEMPERATURE & HUMIDITY 16
AUTO-SCANNING 17
PROGRAMMABLE TEMPERATURE ALARM 17
COMFORT LEVEL INDICATORS 18
Honeywell
MAXIMUM AND MINIMUM READINGS 19
Barometric Weather Forecaster
LOST COMMUNICATION 19
TRA
Streszczenie treści zawartej na stronie nr. 2
INTRODUCTION BEFORE YOU BEGIN Thank you for selecting the Honeywell Barometric Weather Forecaster. This • We recommend using alkaline batteries for the remote temperature device combines precise time keeping with monitoring and displaying the and humidity sensor and the main unit when temperatures are above temperature/humidity data from up to three remote locations. 32°F (0°C). We recommend using lithium batteries for the remote In this package you will find: sensor when temperatures are
Streszczenie treści zawartej na stronie nr. 3
and maintenance. D. CHANNEL SWITCH We recommend cleaning the remote sensor periodically, as the dirt and debris • Selects the desired channel -1,2 or 3 may affect sensor accuracy. E. WALL-MOUNT RECESSED OPENING • Keeps the remote sensor on the wall F. °C/°F SWITCH PRODUCT OVERVIEW • Selects the temperature display in Fahrenheit or Celsius REMOTE TEMPERATURE & HUMIDITY SENSOR FEATURES NOTE: Install the batteries; select the channel and temperature in °C or °F • Remote data transmis
Streszczenie treści zawartej na stronie nr. 4
with a free air circulation and sheltered from the direct sunlight and an Weather extreme weather conditions. • Weather forecast for the next 12 to 24 hour in five large icons: Sunny, Partly Cloudy, Cloudy, Rainy and Snowy • Ideally, place the thermo-hygrometer sensor above the natural surfaces (such as a grassy lawn). • Barometric pressure in imperial or metric units • Avoid placing the thermo-hygrometer sensor near sources of heat, • Altitude adjustment for pressure compensation such
Streszczenie treści zawartej na stronie nr. 5
• Allows toggling between two different clock modes – time with seconds and time with the day of the week • When depressed and held, activates clock programming mode • Confirms programmed parameters D. ALARM button • Allows toggling between the calendar display and three time alarm modes • When depressed and held, enters into the alarm programming mode for a selected parameter E. TEMP ALARM button REAR/SIDE • Allows toggling between high/low limits for temperature alarm and curren
Streszczenie treści zawartej na stronie nr. 6
• Allows displaying pressure history records • When mounting the main unit on the wall or vertical surface, remove J. SNOOZE/LIGHT button the table stand from the unit. PLACEMENT • Stops all alarms temporarily • Activates a backlight for 5 seconds • Make sure that the main unit is locating within the operating range of K. Back panel UP ( ▲) button the remote sensor Increases the parameters of pressure and altitude • Ideally the remote sensor should be mounted within the line of sight
Streszczenie treści zawartej na stronie nr. 7
SEA LEVEL barometric pressure option should be selected. In this case, the • Press UP or DOWN to adjust an altitude value. Press and hold either SEA LEVEL barometric pressure value can be adjusted according to the local button for the advanced setting. metro area weather information. (Sources – local TV or radio station, etc). • Press PRESSURE/ALTITUDE button to confirm the programmed NOTE: Locate your altitude with a portable GPS receiver or topographical altitude. map .Locate barometric
Streszczenie treści zawartej na stronie nr. 8
PROGRAMMING SEA LEVEL PRESSURE • Press PRESSURE/ALTITUDE button on the back until the pressure with “SEA LEVEL” mark is displayed. • Press and hold PRESSURE/ALTITUDE button until the pressure digits are flashing. • Set the sea level pressure by pressing UP or DOWN buttons. Press and hold either button for the quick digits advance. MOON PHASE ICONS • Press PRESSURE/ALTITUDE button to confirm selection. REMOTE AND INDOOR TEMPERATURE & HUMIDITY After batteries are installed; remote
Streszczenie treści zawartej na stronie nr. 9
flash The indoor temperature and humidity with the icon IN are located below the • Use UP( ▲) or DOWN( ) arrow buttons to adjust the higher remote temperature and humidity information line. temperature limit NOTE: If the indoor or remote temperature or humidity goes above or below • Press the TEMP ALARM button to confirm the selected value operating range stated in specifications, the main unit’s display ( weather) will • Press the TEMP ALARM button once to enter into the Low show
Streszczenie treści zawartej na stronie nr. 10
-5°C to 50°C • Bring the main unit and remote sensor close together. OVER Contains excess WET (23°F • Remove four (4) small screws from the back of the remote sensor with 70%RH moisture small Phillips screwdriver, and open the battery compartment. to122°F) 5°C to 50°C • Remove the batteries from the battery compartment and reinstall them BELOW Contains inadequate in the same manner. Remote sensor LED indicator will flash showing DRY (23°F 40%RH moisture transmission of the signal.
Streszczenie treści zawartej na stronie nr. 11
atomic time signal from the NIST Atomic clock in Boulder, Colorado. After the clock is set manually, place the Weather Forecaster by the window for The WWVB tower icon on the unit’s display will flash indicating a radio signal the better reception. The atomic clock receiver is programmed that it will reception from the WWVB station. If the tower icon is not fully lit, or if the time continue to search for the atomic time signal daily for every hour between 1:00 and date are not set automatica
Streszczenie treści zawartej na stronie nr. 12
next parameter (month) • Press ALARM button again. The minute digits will flash • Continue setting month, date, hour, minutes, language for the day of • Adjust the minutes using UP ( ▲) or DOWN ( ▼) buttons the week and temperature in Fahrenheit or Celsius • Press ALARM button again to confirm and the weekday alarm time will be set • Press MODE for the last time to return to the time of day with seconds, after the last parameter is set • Set Single (S) day alarm if desired in the same ma
Streszczenie treści zawartej na stronie nr. 13
If the alarm is not disabled after that, it will sound for two more minutes and PRECAUTIONS then will stop by itself. This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: BACKLIGHT • Do not immerse the units in water. The backlight feature is enabled only after the time is set. • Do not clean the units with abrasive or corrosive materials. They may To activate the backlight press the SNOOZE/LIGHT button once, and both – s
Streszczenie treści zawartej na stronie nr. 14
User-selectable (°F or °C) temperature display FCC STATEMENT Remote channels auto-scan feature This device complies with Part 15 of the FCC Rules. Operation is subject to the Maximum number of remote sensors: 3 (one included) Readings update interval: every 45 seconds following two conditions: (1) This device may not cause harmful interference, Low battery indicators – for each remote channel and main unit and (2) This device must accept any interference received, including EL backligh
Streszczenie treści zawartej na stronie nr. 15
DECLARATION OF CONFORMITY STANDARD WARRANTY INFORMATION We This product is warranted from manufacturing defects for one year from date of Name: Hideki Electronics, Inc. retail purchase. It does not cover damages or wear resulting from accident, Address: 7865 SW Mohawk misuse, abuse, commercial use, or unauthorized adjustment and repair. Tualatin, OR 97062 Note that online product registration is required to ensure valid warranty declare that the product protection. Product No.: TE
