Streszczenie treści zawartej na stronie nr. 1
MN-800-TF
REVERSE OSMOSIS TREATMENT SYSTEM
OWNERS MANUAL
Nimbus Water Systems
41840 McAlby Court, Suite A
Murrieta, CA 92562-7036
800-451-9343
Streszczenie treści zawartej na stronie nr. 2
THE NIMBUS MN-800 TF REVERSE OSMOSIS TREATMENT SYSTEM TABLE OF CONTENTS §1.0 MN-800 TF SYSTEM SPECIFICATIONS .......................................................................... 3 §2.0 SYSTEM COMPONENTS (See Figure 1).......................................................................... 3 §3.0 PRE-INSTALLATION PROCEDURES............................................................................... 7 §4.1 LOCATION .......................................................
Streszczenie treści zawartej na stronie nr. 3
THE NIMBUS MN-800 TF REVERSE OSMOSIS TREATMENT SYSTEM The Nimbus MN-800 TF is the perfect system for a wide variety of applications. Features include stainless steel pressure vessels, frame and concentrate recirculation valve. There are pressure gauges on the pre-filter outlet, post-filter inlet and the high pressure outlet of the desalinator array. The MN-800 TF is also equipped with a 20" 10µ (micron) carbon cartridge pre-filter and post- filter. An Auxiliary 10 Post Filter with a
Streszczenie treści zawartej na stronie nr. 4
4
Streszczenie treści zawartej na stronie nr. 5
CONCENTRATE RECIRCULATION VALVE: A needle valve that controls the amount of concentrate from the desalinator array to be recirculated back into the feed stream. This feature allows for higher recovery rates. Additionally, adjustment of this valve regulates the pump discharge pressure. FLOW CONTROL: A fixed orifice that controls the amount of water flowing across the membrane to drain. PRODUCT WATER CHECK VALVE: A one-way valve that prevents pressurized product water from flowing bac
Streszczenie treści zawartej na stronie nr. 6
ANCILLARY EQUIPMENT: The following items are also covered in this manual to form a complete water treatment system. PRESSURE TANK: The tank provides storage for approximately 34 gallons of treated water at a pressure of 40 to 60 psi. REMOTE BY-PASS PANEL: This panel monitors treated water TDS and storage tank pressure. It includes a valve for switching to delivery of city water to the food service machines in the event of an RO system failure. INSTALLATION KIT: This kit contains f
Streszczenie treści zawartej na stronie nr. 7
§3.0 PRE-INSTALLATION PROCEDURES PLEASE READ CAREFULLY. FAILURE TO FOLLOW THESE PROCEDURES CAN RESULT IN DAMAGE TO YOUR SYSTEM AND VOID YOUR WARRANTY. §3.1 PACKAGING Upon delivery, inspect packaging for damage and report it to your carrier at that time. After unpacking the system, inspect it carefully for signs of damage. All damage claims should be made to the delivery carrier. §3.2 OPERATING LIMITATIONS Nimbus MN-800 TF units are to be used on potable water only. The use
Streszczenie treści zawartej na stronie nr. 8
§4.0 INSTALLATION PLEASE READ CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE PROCEDURES CAN RESULT IN DAMAGE TO YOUR SYSTEM AND VOID YOUR WARRANTY. §4.1 LOCATION It is recommended that systems be located where they are protected from harsh environments such as rain, snow and extreme temperatures (both hot and cold). MN-800 TF units can be located just about anywhere there is a water and electrical supply. This can be on the floor, mounted on the wall with a shelf,
Streszczenie treści zawartej na stronie nr. 9
9
Streszczenie treści zawartej na stronie nr. 10
piece of black 5/8 tubing from the valve up to the 5/8 compression fitting at the back right side of the RO system manifold. §4.2.2 BY-PASS PANEL PREPARATION AND INSTALLATION: The by-pass panel is to be located convenient to the RO where the TDS monitor is visible and the valve can be operated without difficulty. The standard fittings provided are ½ MPT x 5/8 compression to be installed directly in the 3 ½ FPT ports at the bottom of the panel. Three ½ street elbows are also pro
Streszczenie treści zawartej na stronie nr. 11
11
Streszczenie treści zawartej na stronie nr. 12
§5.0 SYSTEM FLUSH AND PERFORMANCE VERIFICATION Although MN-800-TF systems are fully tested at the factory prior to shipping, it is recommended to flush and verify your system's performance on-site. §5.1 SYSTEM FLUSH AND OPERATION New membranes have a preservative on them that needs to be flushed before use. Open the fast flush valve and all usage outlets to allow product to run to drain. • Fully open the concentrate recirculation valve by turning the knob counterclockwise. •
Streszczenie treści zawartej na stronie nr. 13
As a final check turn on the city water valve to the By-Pass Panel and check the plumbing • for leaks. §5.2 PERFORMANCE VERIFICATION Factory test data is supplied with the system. To ensure optimum performance, on-site data should be taken and compared to the factory test data. This data should be taken after the system has been flushed for one hour. Some deviations may be seen due to differences in feed water TDS and temperature between the site and factory. If you have already conn
Streszczenie treści zawartej na stronie nr. 14
gauge reads about 60 psi (4.1 bar). Now, by opening the tank inlet valve the tank pressure should begin to drop and the system should turn on when the pressure drops below about 40 psi (2.8 bar). If the system fails to shut off at 60 psi (4.1 bar), watch the gauge and be sure that it does not rise above 80 psi (5.5 bar). If it reaches 80 psi (5.5 bar), unplug the system. Refer to §7.1.2 for TANK PRESSURE SWITCH ADJUSTMENT. §6.0 OPERATION AND MAINTENANCE Nimbus MN-800-TF systems are de
Streszczenie treści zawartej na stronie nr. 15
psi (1.4 bar). Before servicing, always disconnect power to the unit to avoid shock. • To adjust, remove cover and refer to the diagram inside the cover. • Turn adjustment nut #1 counterclockwise to decrease cut-out pressure and clockwise to • increase cut-out pressure. Under normal circumstances it is not necessary to adjust this switch setting. Replace cover and restore power to unit. • ALWAYS BE SURE TO CHECK THE CUT-OUT OPERATION AFTER ADJUSTMENT AS OUTLINED IN §
Streszczenie treści zawartej na stronie nr. 16
Tag and disconnect the three tubing connections on the desalinator namely the feed, • concentrate and product. Unsnap the desalinator retainers and pull desalinator(s) out. • Remove retaining clips from ends of desalinator by tapping the open ends of the clips with • a plastic or rawhide mallet until they are through the slots in the pressure vessel. Pull clips completely out of pressure vessel. Remove end plugs by gently pulling on the fittings. Do not use pliers on the fittin
Streszczenie treści zawartej na stronie nr. 17
17
Streszczenie treści zawartej na stronie nr. 18
Since the membrane is new it will need to be flushed and tested. Follow procedures • outlined in §5.0 SYSTEM FLUSH AND PERFORMANCE VERIFICATION. §7.4 PRE FILTER CARBON CARTRIDGE REPLACEMENT Before servicing, always disconnect power to the unit to avoid shock. • Close feed water and tank valves. • Activate the switch on the side of the gray box in the back of the unit just enough to relieve • any pressure in the filter. Remove pre-filter sump by turning clockwise (as viewed
Streszczenie treści zawartej na stronie nr. 19
Inspect sump for cracks. Replace as necessary. • Lubricate O-ring with an appropriate petroleum or silicone-based lubricant. Install O-ring • into its seat in sump. Install new carbon cartridge with the white rubber ring up. • Replace sump by screwing it onto cap in a counter-clockwise direction (as viewed from • top). A wrench should not be needed. Hand tightened is sufficient. Restore water and power; check for leaks. • ● Note: New carbon cartridges need to be fl
Streszczenie treści zawartej na stronie nr. 20
§8.0 PARTS AND ACCESSORIES PART NUMBER DESCRIPTION ITEM MOTORS & PUMPS 102612 Motor, ¾ HP 101168 Clamp, V Band 101199 Pump, 165 gph, Brass DESALINATORS, MEMBRANES & 104459 Desalinator, TF, Complete (MN-800 TF & MN-800 TF) HOUSINGS 100716 Membrane, AG2525 (High Rejection) 104167 Pressure Vessel, Stainless Steel 104157 Interconnector, Product End, w/ORings 104159 Interconnector, Closed End, w/ORings 104198 Product End Plug 104186 Closed E
