Streszczenie treści zawartej na stronie nr. 1
KOBE Brand Range Hood
Model No. CH7730SQB
CH7736SQB
CH7742SQB
CH7748SQB
CH-77 SERIES – 10" HEIGHT
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
Streszczenie treści zawartej na stronie nr. 2
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS................................................................................1 COMPONENTS OF PACKAGE..............................................................................................3 INSTALLATION ......................................................................................................................4 OPERATING INSTRUCTIONS............................................................
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. 2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. 3) Ducted
Streszczenie treści zawartej na stronie nr. 4
What to Do In The Event Of a Range Top Grease Fire � SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911. � NEVER PICK UP A BURNING PAN – You May Get Burned. � DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result. � Use an extinguisher ONLY if: a) You hav
Streszczenie treści zawartej na stronie nr. 5
COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box – (Sold Separately) {A} KOBE Range Hood - 1 {H} KOBE Adjustable Duct Cover - 1 {B} Warranty Registration Card - 1 {I} Screws Package – 1 {C} Instructions Manual - 1 {J} Duct Cover-Mounting Bracket – 1 {D} Baffle Filter - 2 (for 30”, 36”, 42” hood) {K} Hood-Mounting Bracket – 1 - 3 (for 48” hood) (E}Bottom Casing
Streszczenie treści zawartej na stronie nr. 6
INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1. (All calculation in inches.) - FOR UNDER THE CABINET - TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36") C = Preferred Height of Counter Top to Hood Bottom (Recommended 27" to 30") D = Height of Hood E = Height of the Cabinet
Streszczenie treści zawartej na stronie nr. 7
SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. Installation Contents UNDER THE CABINET Top Vent………………………………………………………………………………… 6 Rear Vent……………………………………………………………………………….. 8 WALL MOUNT Top Vent………………………………………………………………………………… 10 Rear Vent……………………………………………………………………………….. 1
Streszczenie treści zawartej na stronie nr. 8
UNDER THE CABINET INSTALLATION – TOP VENT Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. - A straight, short venting run will allow the hood to perform more efficiently. - Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. - Temporarily wire the hood to
Streszczenie treści zawartej na stronie nr. 9
1. Puncture the knockout holes on the hood as shown in Figure 4. 2. Unscrew the six screws on the bottom casing. Remove the bottom casing or remove the baffle filters and spacers. If necessary, arrange the electrical wires to run through the 1” diameter hole on the top or the rear of the hood. Refer to Figure 5. 3. Using references on Table 1 and measurements on page 21 center the hood in place beneath the cabinet and flush with the front of the cabinet.
Streszczenie treści zawartej na stronie nr. 10
UNDER THE CABINET INSTALLATION – REAR VENT Preparation before installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 6. - A straight, short venting run will allow the hood to perform more efficiently. - Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. - Temporarily wire the hood to te
Streszczenie treści zawartej na stronie nr. 11
Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes on the hood as shown in Figure 10. 2. Unscrew and remove the multi duct exhaust. Replace with {F} vent cover (top) on page 3. Refer to Figure 11. Figure 10
Streszczenie treści zawartej na stronie nr. 12
WALL MOUNT INSTALLATION – TOP VENT ***This installation only applied with the purchase of a duct cover (Model No. CH1120DC). Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 13. - A straight, short venting run will allow the hood to perform more efficiently. - Try to avoid
Streszczenie treści zawartej na stronie nr. 13
- If necessary, attach two rubber stands (provided) with two (4x8 mm) screws (provided) to the back of the hood. - Attach the hood-mounting bracket to the back of the hood with nine (3/16" x 3/8") screws (provided) as shown in Figure 16. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references on Table 2 and measurements on page
Streszczenie treści zawartej na stronie nr. 14
Figure 18 Figure 19 7. Adjust the height of the inner duct cover to the duct cover-mounting bracket. Secure the inner duct cover with two (4x8 mm) screws (provided) as shown in Figure 20. Attach Together Figure 20 8. Fasten outer duct cover to multi vent ex
Streszczenie treści zawartej na stronie nr. 15
WALL MOUNT INSTALLATION – REAR VENT ***This installation only applied with the purchase of a duct cover (Model No. CH1120DC). Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. - Decide the location of the venting pipe from the hood to the outside. Refer to Figure 21. - A straight, short venting run will allow the hood to perform more efficiently. - Try to avoid as many transitions, elbows, and long run as possible. This
Streszczenie treści zawartej na stronie nr. 16
- If necessary, attach two rubber stands (provided) with two (4x8 mm) screws (provided) to the back of the hood. - Attach the hood-mounting bracket to the back of the hood with nine (3/16" x 3/8") screws (provided) as shown in Figure 25. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn OFF the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Using references on Table 2 and measurements on page
Streszczenie treści zawartej na stronie nr. 17
Figure 27 Figure 28 7. Adjust the height of the inner duct cover to the duct cover-mounting bracket. Secure the inner duct cover with two (4x8 mm) screws (provided) as shown in Figure 29. Attach Together Figure 29 8. Fasten outer duct cover to multi vent exhaust on the hood with four (4x8 mm) screws (provided). 9. Continued at “Install Accessories” on page 16. 15
Streszczenie treści zawartej na stronie nr. 18
Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. - If necessary to hide the electrical wire connections, push wires back into the wiring bo
Streszczenie treści zawartej na stronie nr. 19
OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30-second delay shutoff, two powerful centrifugal turbine impellers with safety screens, two bright 12-volt 20-watt halogen lights, and four oil containers or baffle filters. The four electronic controls are Light Control, Speed Control A (cycles through Low, Medium, High, QuietMode™ ), Speed Control B (cycles through Low, QuietMode™ , High, Medium) and the Power Contr
Streszczenie treści zawartej na stronie nr. 20
MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. Cleaning Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. DO NOT USE PAPER TOWEL ON STAINLESS STEEL. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. DO NOT USE
