Instrukcja obsługi Pontiac 95-3528

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-3528
APPLICATIONS
PONTIAC GTO
2004-2006
95-3528
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Brackets • B) Double DIN Trim plate
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• 86-3528 Radio Removal Keys
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

95-3528 TABLE OF CONTENTS Dash Disassembly - Pontiac GTO 2004-2006 . .... ........ ....... ........ ........ .....1,2 Kit Assembly - Double DIN Radio Provision ..... ........ ...... .. ....... ..... ... ...3 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 *Note: Refer also to the instructions included with the aftermarket radio.

Streszczenie treści zawartej na stronie nr. 3

95-3528 DASH DISASSEMBLY PONTIAC GTO 2004-2006 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Using the radio removal keys, pull the factory radio from the dash and dis- connect the wiring. (Figure A) 3 Unsnap and remove the trim panel at the top center of the dash above the A/C vents and remove (4) Phillips screws. (Figure B) B 4 Remove (1) Phillips screw from inside lower open storage area where center console and dash meet. (Figure C) 5 Unsnap and rem

Streszczenie treści zawartej na stronie nr. 4

95-3528 DASH DISASSEMBLY PONTIAC GTO 2004-2006 E 6 Remove (2) Phillips screws exposed at the bottom of the center panel sur- rounding radio and remove panel. (Figure E) 7 Unclip and remove trim panel sur- rounding radio and A/C controls. 8 Remove (3) Phillips screws holding "cage" in radio opening. (Figure F) 9 Pull down on the "cage" from the opening inside on the top and F remove. (Figure G) Continue to final assembly. G 2

Streszczenie treści zawartej na stronie nr. 5

95-3528 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets to the Double DIN radio unit using the screws supplied with the radio. (Figure A) Continue to final assembly. 3

Streszczenie treści zawartej na stronie nr. 6

95-3528 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets to the stacked ISO mount units using the screws supplied with the units. (Figure A) Continue to final assembly. 4

Streszczenie treści zawartej na stronie nr. 7

95-3528 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Insert and secure the radio/bracket assembly into the radio op

Streszczenie treści zawartej na stronie nr. 8

95-3528 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/07/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST95-3528