Instrukcja obsługi Metra Electronics 99-8225G

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8225G
APPLICATIONS
Toyota Venza
2009-2010
99-8225G
KIT FEATURES
• DIN Head Unit Provision With Pocket
• ISO DIN Head Unit Provision With Pocket
• Painted to match factory dash - G=Gray
KIT COMPONENTS
• A) Single DIN Radio Housing • B) ISO Brackets • C) Trim Plate
B C
A
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-1761 - 1987-up Toyota harness
• TYTO-01 - 2003-up Toyota JBL amp interface
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel

Streszczenie treści zawartej na stronie nr. 2

99-8225G TABLE OF CONTENTS Dash Disassembly - Toyota Venza 2009-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Din Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . 3 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognize

Streszczenie treści zawartej na stronie nr. 3

99-8225G DASH DISASSEMBLY Toyota Venza 2009-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel to the right of the shifter. (Figure A) 3 Remove (1) Phillips screw from the bottom of the climate control then unclip and remove the climate control. (Figure B) 4 Remove (4)10 MM bolts securing the radio. Note: You will need a univer- B sal swivel head socket adapter to get to the bottom left bolt. (Figure C) 5 Remove (4) Phil

Streszczenie treści zawartej na stronie nr. 4

99-8225G KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Secure the Radio Housing into the A factory a/c vent panel using the factory hardware. (Figure A) REAR VIEW - A/C VENT PANEL 2 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 3 Slide the DIN cage into the Radio H

Streszczenie treści zawartej na stronie nr. 5

99-8225G KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Secure the Radio Housing into the A factory a/c vent panel using the factory hardware. (Figure A) REAR VIEW - A/C VENT PANEL 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) 4 Snap the Trim Plate into the Radio Housing. (Figure C)

Streszczenie treści zawartej na stronie nr. 6

99-8225G NOTES 4

Streszczenie treści zawartej na stronie nr. 7

99-8225G NOTES 5

Streszczenie treści zawartej na stronie nr. 8

99-8225G INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/20/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-8225G