Instrukcja obsługi Metra Electronics 99-7425

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7425
APPLICATIONS
Nissan Rogue 2008-10
99-7425
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) Trim Plate • C) ISO Brackets
B
Harness & Antenna Connections (sold separately)
• 70-7552 - Nissan Harness 07-up
A
• 40-NI12 - Nissan Antenna Adapter 07-up
C
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 www.metraonline

Streszczenie treści zawartej na stronie nr. 2

99-7425 TABLE OF CONTENTS Dash Disassembly - Nissan Rogue 2008-10 . ... ... .... ... .... ... .... ... ...1,2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO MOUNT Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 *Note: Refer also to the instructions included with the aftermarket radio.

Streszczenie treści zawartej na stronie nr. 3

99-7425 DASH DISASSEMBLY NISSAN Rogue 2008-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 If equipped with center speaker: Unclip and remove the grille (Figure A). Remove (4) Phillips screws securing the speaker. Unplug and remove the speaker. (Figure B). Unclip the panel above the radio including the a/c vents, then unplug hazard switch and remove. (Figure C) B Note: If not equipped with center speaker skip step number 2. Continued on page 2. C 1

Streszczenie treści zawartej na stronie nr. 4

99-7425 DASH DISASSEMBLY NISSAN Rogue 2008-10 D 3 Unclip the panel below the radio including the climate controls. Unplug climate controls and remove the panel. (Figure D) 4 Remove (4) Phillips screws securing the radio, unplug and remove radio. (Figure E) Continue to kit assembly. A/C PASS AIR BAG E 2

Streszczenie treści zawartej na stronie nr. 5

99-7425 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. B 3

Streszczenie treści zawartej na stronie nr. 6

99-7425 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) B Continue to final assembly. 4

Streszczenie treści zawartej na stronie nr. 7

99-7425 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble in reverse order of disassembly. FINAL WIRING CONNE

Streszczenie treści zawartej na stronie nr. 8

99-7425 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/29/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7425