Streszczenie treści zawartej na stronie nr. 1
CD-RECEIVER
KDC-334SA
KDC-334SG
INSTRUCTION MANUAL
© B64-3240-00/00 (EW/E2W)
Streszczenie treści zawartej na stronie nr. 2
Contents Safety precautions 3 Menu system 17 Menu System Notes 4 Touch Sensor Tone Manual Clock Adjustment About CDs 5 Synchronize Clock Power OFF Timer General features 6 News Bulletin with Timeout Setting Power Local Seek Selecting the Source Tuning Mode Volume AF (Alternative Frequency) Attenuator Restricting RDS Region (Region Restrict System Q Function) Auto TP Seek Audio Control Audio Setup Monaural Reception Speaker Setting Accessories/ Switching Clock Display Installation Procedure 20
Streszczenie treści zawartej na stronie nr. 3
Safety precautions 2WARNING To prevent injury or fire, take the following precautions: • To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. 2CAUTION To prevent damage to the machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibili
Streszczenie treści zawartej na stronie nr. 4
Notes • If you experience problems during installation, This Product is not installed by the manufacturer consult your Kenwood dealer. of a vehicle on the production line, nor by the professional importer of a vehicle into an EU • If the unit fails to operate properly, press the Reset Member State. button. The unit returns to factory settings when the Reset button is pressed. The marking of products using lasers (Except for some areas) CLASS 1 ATT TI AME LASER PRODUCT Reset button The la
Streszczenie treści zawartej na stronie nr. 5
About CDs Handling CDs Removing CDs • Do not touch the recording surface of the CD. When removing CDs from this unit pull them out horizontally. CDs that can’t be used • CDs that are not round cannot be used. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Do not stick tape etc. on the CD, or use a CD with • CDs with coloring on the recording surface or that tape stuck on it. are dirty cannot be used.
Streszczenie treści zawartej na stronie nr. 6
General features Release button Control knob ATT TI AME ATT VOL Q SRC LOUD indicator General General Clock display ATT indicator Volume Power Increasing Volume Turning ON the Power Turn the [VOL] knob clockwise. Press the [SRC] button. Decreasing Volume Turning OFF the Power Turn the [VOL] knob counterclockwise. Press the [SRC] button for at least 1 second. Selecting the Source Attenuator Turning the volume down quickly. Press the [SRC] button. Press the [ATT] button. Source required Display Eac
Streszczenie treści zawartej na stronie nr. 7
System Q 4 Adjust the Audio item Turn the [VOL] knob. Selecting the best sound setting preset for different types of music. Adjustment Item Display Range Bass level "BAS L" –8 — +8 1 Select the source to set Middle level "MID L" –8 — +8 Press the [SRC] button. Treble level "TRE L" –8 — +8 Balance "BAL" Left 15 — Right 15 2 Select the Sound type Fader "FAD" Rear 15 — Front 15 Press the [Q] button. Exit Audio Control mode (Volume control mode) Each time you press the button, the sound setting
Streszczenie treści zawartej na stronie nr. 8
General features Audio Setup Speaker type Display OFF "SP OFF" Setting the Sound system, such as Volume offset For 5 & 4 in. speaker "SP 5/4" and Loudness. For 6 & 6x9 in. speaker "SP 6x9/6" For the OEM speaker "SP OEM" 1 Select the source to adjust Press the [SRC] button. 4 Exit Speaker Setting mode 2 Enter Audio Setup mode Press the [VOL] knob. Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item to adjust Press the [VOL] knob. Each time you press the knob, the item to be
Streszczenie treści zawartej na stronie nr. 9
2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing you to use the unit. TEL Mute The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears and the audio system comes back ON. | English 9
Streszczenie treści zawartej na stronie nr. 10
Tuner features Control knob ATT TI AME SRC 1-6 AME Band display Preset station number ST indicator Frequency display Tuning Station Preset Memory Selecting the station. Putting a station in the memory. 1 Select tuner source 1 Select the band Press the [SRC] button. Push the Control knob towards [FM] or [AM]. Select the "TUNER" display. 2 Select the frequency to put in the memory 2 Select the band Push the Control knob towards [4] or Push the Control knob towards [FM] or [AM]. [¢]. Each time you
Streszczenie treści zawartej na stronie nr. 11
Auto Memory Entry Putting stations with good reception in the memory automatically. 1 Select the band for Auto Memory Entry Push the Control knob towards [FM] or [AM]. 2 Open Auto Memory Entry Press the [AME] button for at least 2 seconds. "A-MEMORY" is displayed. When 6 stations that can be received are put in the memory Auto Memory Entry closes. • When the (page 19) is ON, only RDS stations are put in the memory. • When Auto Memory Entry is done in the FM II ba
Streszczenie treści zawartej na stronie nr. 12
RDS features Control knob ATT TI AME 1-6 TI TI indicator PTY indicator Receiving other traffic information stations Traffic Information Push the Control knob towards [4] or Changing to traffic information automatically [¢]. when a traffic bulletin starts even when you are not listening to the radio. • Traffic information can be switched when it is on the Press the [TI] button. Tuner Source. However, you cannot switch the Traffic Each time you press the button, the Traffic information durin
Streszczenie treści zawartej na stronie nr. 13
2 Select the Program Type 3 Search for the selected Program Type Push the Control knob towards [FM] or [AM]. station Each time you push the knob, the Program Type Push the Control knob towards [4] or alternates between the program types shown in [¢]. the table below. When you want to search for other stations, push [4] or [¢] of the Control knob again. No. Program Type Display 1. Speech "SPEECH" 2. News "NEWS" • When the selected Program Type is not found, "NO 3. Current Affairs "AFFAIRS" PT
Streszczenie treści zawartej na stronie nr. 14
RDS features Changing Language for PTY Function Selecting the Program Type display language. 1 Enter PTY mode Refer to (page 12). 2 Enter Changing Language mode Press the [TI] button. 3 Select the language Push the Control knob towards [FM] or [AM]. Each time you push the knob, the language alternates between the languages shown in the table below. Language Display English "ENGLISH" French "FRENCH" German "GERMAN" 4 Exit Changing Language mode Press the [TI] button. | 14
Streszczenie treści zawartej na stronie nr. 15
CD player features 0 ATT TI AME SRC SCAN RDM REP Control knob IN indicator Track number Track time Fast Forwarding and Reversing Playing CD Fast Forwarding When a disc is inserted Hold down toward [¢] with the Control Press the [SRC] button. knob. Select the "CD" display. Release your finger to play the disc at that point. Reversing • When a CD is inserted, the "IN" indicator is ON. Hold down toward [4] with the Control Pause and play knob. Press the Control knob. Release your finger to play t
Streszczenie treści zawartej na stronie nr. 16
CD player features Track Search Selecting the song you want to hear. Push the Control knob towards [4] or [¢]. Track Repeat Replaying the song you are listening to. Press the [REP] button. Each time you press the button, the Track Repeat turns ON or OFF. When the Track Repeat is ON, "TRAC REP" is displayed. Scan Play Playing the first part of each song on the disc you are listening to and searching for the song you want to hear. 1 Start Scan Play Press the [SCAN] button. "TRAC SCN" is displ
Streszczenie treści zawartej na stronie nr. 17
Menu system ATT TI AME MENU Control knob RDS indicator Menu display You can continue by returning to step 2 and Menu System setting other items. Setting beep sound during operation, etc. 4 Exit Menu mode functions. Press the [MENU] button. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation • When other items those applicable to the basic explanation. operation method above are displayed, their setting
Streszczenie treści zawartej na stronie nr. 18
Menu system In Standby mode In Standby mode Touch Sensor Tone Power OFF Timer Setting the operation check sound (beep sound) Setting the timer to turn this unit’s power OFF ON/OFF. automatically when Standby mode continues. Using this setting can save the vehicle’s battery Display Setting power. "BEEP ON" Beep is heard. "BEEP OFF" Beep canceled. Display Setting "OFF – – –" Power OFF Timer function is OFF. "OFF 20M" Turns the power OFF after 20 minutes. (Original setting) "OFF 40M" Turns the po
Streszczenie treści zawartej na stronie nr. 19
In Tuner mode Restricting RDS Region (Region Local Seek Restrict Function) Only stations whose reception is good are You can choose whether or not to restrict the searched in auto seek tuning. RDS channels, received with the AF function for a particular network, to a specific region. Display Setting "LO.S OFF" The local seek function is OFF. Display Setting "LO.S ON" The local seek function is ON. "REG ON" The Region Restrict Function is ON. "REG OFF" The Region Restrict Function is OFF. • I
Streszczenie treści zawartej na stronie nr. 20
Accessories/ Installation Procedure • If your vehicle’s ignition does not have an ACC position, Accessories or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on 1 and off along with the ignition). If you want to link the unit’s power with the ignition, connect the ignition wire ..........1 to a power source that can be turned on and off with the ignition key. • If the
