Instrukcja obsługi JL Audio Stealthbox SB-GM-SLVCNSL/10W3

Streszczenie treści zawartej na stronie nr. 1

SB-GM-SLVCNSL/10W3
Stealthbox™
Fits 2000 Extended-Cab Full-Size GM Pickup Trucks
and Suburban, Tahoe, Yukon, Yukon XL SUV's
Installation Guide:
This Stealthbox is a product which requires professional installation skills and tools. Please read this installa-
tion guide thoroughly before beginning the project. It will guide you step by step through the installation.
Several of the steps in this process may require two people to accomplish.
It is absolutely vital that the enclosure be properly m

Streszczenie treści zawartej na stronie nr. 2

STEP 4: Remove the additional mounting screws at the bottom of the storage tray. STEP 5: Remove the screws around the upper edge of the storage tray. STEP 6: Open the door at the rear of the console to its maximum extension. STEP 7: Remove the two screws at the hinge point. STEP 8: Remove the cup holder. STEP 9: Remove the two screws as shown in the picture to the right. These screws secure the internal storage tray from the rear. SB-GM-SLVCNSL/10W3-D6, JL AUDIO, Inc 2000 • Page 2 Sheet S

Streszczenie treści zawartej na stronie nr. 3

STEP 10: Remove the internal storage tray. STEP 11: Pull the console body toward the rear in order to release it from the duct work. Remove the console body from the vehicle. STEP 12: Remove and discard the duct. STEP 13: Modify the internal storage tray by cutting around its perimeter approximately 1 1/2" below the upper lip. SB-GM-SLVCNSL/10W3-D6, JL AUDIO, Inc 2000 • Page 3 Sheet SKU#011142 Revision 8/15/00

Streszczenie treści zawartej na stronie nr. 4

STEP 14: Apply the supplied templates to the proper sides of the console body (as indicated on the template). The templates show where to cut the console body as well as where to drill two holes through the console body. Drill and cut where indicated. STEP 15: Drill a 3/8" hole through the stock mounting bracket at each of the four locations indicated in Diagram #1. 1" 1" 1 9/16" 1 9/16" X X X X 2 1/2" 2 1/2" Diagram #1 STEP 16: Run speaker wire to the console area. STEP 17: Bolt the brack

Streszczenie treści zawartej na stronie nr. 5

STEP 18: Clip the section of the original storage tray rim in the area shown in the picture and in Diagram #2. This will allow the clasp to grasp the new pocket insert only (not both the console body and the new insert). Cut Here Before After Diagram #2 STEP 19: Install the original tray (modified in steps 13 and 18) with the new provided insert. STEP 20: Connect the speaker wire to the Stealthbox. Mount the bracket/Stealthbox into the vehicle. SB-GM-SLVCNSL/10W3-D6, JL AUDIO, Inc 2000 • Pa

Streszczenie treści zawartej na stronie nr. 6

STEP 21: Place the console body over the Stealthbox. STEP 22: Secure the body with the OEM screws into the dash extension. STEP 23: Drill 7/64" holes into the Stealthbox at the four locations of the holes drilled into the console body. STEP 24: Secure the console body to the Stealthbox through these holes with the supplied screws. This completes the installation. Specifications: Supplied Hardware: Enclosure Type: Acoustic Suspension (Sealed) (4) 1/4" X 2" Bolts Driver Type: JL AUDIO 10W3-D