Instrukcja obsługi Audiovox Rampage ACC40

Streszczenie treści zawartej na stronie nr. 1

6
COMPACT
ACC-40
DIGITAL AUDIO 6 DISC
COMPACT DISC CHANGER
MODEL ACC-40
6-DISC CD CHANGER
WITH WIRED COMMANDER
COMPACT
DIGITAL AUDIO
INSTALLATION MANUAL

Streszczenie treści zawartej na stronie nr. 2

PACKING LIST MAIN UNIT Wired Commander FM Modulator CD Changer 6 COMPACT ACC-40 DIGITAL AUDIO 6 DISC COMPACT DISC CHANGER INSTALLATION PARTS Hex Head Bolt with Washer Base Phillips Head Phillips Head (M5 x 12) Mounting Bracket Screw (Large) Screw (Small) 4 pcs. 2 pcs. 4 pcs. 2 pcs. Screw Hole Cover Labels 5 Meter Din Cable Mounting Angle Adjustment Tool 1 pc. 1 pc. 1 pc. ACCESSORIES CD Magazine Index seal sheet Installation Manual Owner's guide 1 pc. 1 pc. 1 pc. 1 pc. 1

Streszczenie treści zawartej na stronie nr. 3

BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the 4 transport screws. Be sure to remove the screws prior to installation. Retain these screws for future use when transporting the unit for service/maintenance. l Caution l After removing the transport lock screws, place the supplied seals over the screw holes. These seals are used to keep dust out of the unit, which could cause a malfunction. Installation and Wiring Pre

Streszczenie treści zawartej na stronie nr. 4

H 45° V H 45° V INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45° ANGLE INSTALLATION Set the anti-vibration springs to Se

Streszczenie treści zawartej na stronie nr. 5

H 45° V PROCEDURE FOR VERTICAL INSTALLATION Note If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2. Set the anti-vibration springs to position "V". Attach a mounting bracket to each side of the unit, using the 1 2 hex head bolts with washer base. position "V" Bracket Bracket Hex head bolt with washer base Determine the mounting location, and drill four mounting Mount the unit in place, using four large self-tapping P

Streszczenie treści zawartej na stronie nr. 6

H 45° V PROCEDURE FOR 45° ANGLE INSTALLATION Note If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2. Set the anti-vibration springs to position "45°". Attach a mounting bracket to each side of the unit, using the 1 2 4 hex head bolts with washer base. position "45°" Bracket Bracket Hex head bolt with washer base 45° Determine the mounting location, and drill four mounting 4 Mount the unit in place, using four large

Streszczenie treści zawartej na stronie nr. 7

SYSTEM WIRING AND ADJUSTMENT IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT - Some import cars use a special dual antenna “Diversity" system. If your car has this type of antenna system, you will find the antenna cable will To car antenna not fit the socket on the FM modulator. Use of the ACC-40 with “Diversity" systems is not recommended. You may also find some GM cars and others have an antenna plug that is too small to mate with the socket on the FM modulator. If this is found, call Audi

Streszczenie treści zawartej na stronie nr. 8

VEHICLE WIRING +12V Accessory / Switched (ORANGE w/WHITE STRIPE) Connect this wire to a terminal which is energized when the ignition switch is turned to the "ON" or "ACCESSORY" position. IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT - Some import cars use a special dual antenna “Diversity" system. If your car has this type of antenna system, you will find the antenna cable will not fit the socket on the FM modulator. Use of the ACC-40 with “Diversity" systems is not +12V Constant (GREEN w/W