Streszczenie treści zawartej na stronie nr. 1
75451-04 REV D
B
®
S I M P L Y AMAZING
USER’S GUIDE
XL2800HAY
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
USA: 1-800-989-3535
CANADA: 1-888-676-7325
COMMERCIAL: 1-800-242-1378
www.oreck.com
www.oreckcommercial.com
VISIT ONE OF OUR OVER
450 STORE LOCATIONS
•IMPORTANT•
SAVE THIS BOOKLET!
VISIT ONE OF OUR OVER
Includes:
450 STORE LOCATIONS
USA: 1-800-989-4244
CANADA: 1-800-393-8801
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagno
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT BEFORE OPERATING SAFETY INSTRUCTIONS CLEANER, READ ALL When using an electrical appliance, basic INSTRUCTIONS IN THIS precautions should always be followed, including the following: MANUAL CAREFULLY. READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, Table of Contents electric shock, or injury: • Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing. Important Safety Instructions . . . .
Streszczenie treści zawartej na stronie nr. 3
ACCESSORIES Maintenance and Customer Service SOLD SEPARATELY USA: 1-800-989-3535 CANADA: 1-888-676-7325 Your ORECK vacuum cleaner is a product of precise engineering. The motor bearings are permanently lubricated and should not be ITEM PART NUMBER oiled. If you require additional information or have problems with your ORECK appliance, you may call ORECK customer service at: 1. Dust Bag, 8 Pack ® Saniseal , ACDS, CCPK8DW - - In USA 1800 989-3535 Hypo-Allergenic In Canada 1-888-676-7325 2. Belt
Streszczenie treści zawartej na stronie nr. 4
Upper 1 2 3 4 5 Handle Plug (Cord Assembly) Connector Assembly 6 7 8 9 10 Cord dump NOTE: Do not operate the unit while in the upright and locked 11 12 position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation. For Easy Power Cord Storage PRESS UNTIL SNAP fig. 6 Wrap power cord around cord dump on Helping IS HEARD ® Hand handle and cord hook on connector. Secure to "U" shaped part on plug ENFONCEZ JUSQU’À TENE D
Streszczenie treści zawartej na stronie nr. 5
Operating Instructions To Operate change the dust bag frequently. DO NOT FILL ABOVE THE Make sure the disposable paper filter dust bag is in place. LINE INDICATED ON THE DUST BAG. DO NOT operate the cleaner without a paper filter dust bag. Be sure the disposable paper filter dust bag is installed Plug the power cord into an electrical outlet. Choose from the properly. low and high speed settings by pressing the ON/LOW (l) ON/HIGH (ll) - OFF (O) switch on handle assembly when All paper dust bags
Streszczenie treści zawartej na stronie nr. 6
Celoc® Hypo-Allergenic Filter System Troubleshooting Guide The CELOC SMMS outer bag of your vacuum cleaner is high filtration medical material designed to filter the smallest of dust particles. It is important that the inside of the outer bag WARNING: Unplug cord from be cleaned. Turned inside out, vacuum the inside of the outer electrical outlet before servicing. bag or hand wash, with warm water and air dry. For best results, the CELOC SMMS outer bag should be replaced SAVE SERVICE CALLS...CHE
Streszczenie treści zawartej na stronie nr. 7
How to Replace a Worn Belt To Adjust or Replace Brush WARNING: Unplug cord from WARNING: Unplug cord from electrical outlet before servicing. electrical outlet before servicing. Remove the replacement To determine if the brush is belt from the storage worn, place a firm straight channel. edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted. Remove the baseplate by Remove the door by removing 5 screws. Then, removing the hold down remove the b
Streszczenie treści zawartej na stronie nr. 8
4. To reassemble, check O-ring on tube, and replace if Bulb Replacement damaged. Vacuum will not Fan operate properly without the Housing O-ring tube O-ring. Slide O-ring to WARNING: Unplug cord from approximately 2" from base of tube. Replace tube by first electrical outlet before servicing. lining up slot at base of tube with inner tab inside fan • Remove lamp housing housing. Then reinsert tube by removing two (2) D and push down until the tube screws in the the top of is seated. Make sure O-
