Streszczenie treści zawartej na stronie nr. 1
unidE!n$
UHF CB TRANSCEIVER
OWNER'S MANUAL
SUNDOWNER UH-O99
SCANNING
-
SCAN OSlGS
unldm
UH-099 11
ID CAL MEMCUP1SQ " ""
1
D D
SRF os -
"""'j",, GS
r
0 0 ""a"DD_", SCN L,l L,l
gQ 00 ~
S do
un wner ~ o~ ~
With Built-in SELCALL
Streszczenie treści zawartej na stronie nr. 2
Contents Controls/lndicators/Connections 2 FrontPanelControls 2 FrontPanelIndicators 3 Microphone " " ... 4 Back Panel "... 5 Getting Started 6 Mobile Station Installation 6 Choosing an Antenna 6 Ground System 6 Operation 7 Howto Receive " , 7 How to Transmit 7 Scanning 8 Programming Scan Channels 8 Removing Group Scan Channels 9 Open Scanning 9 Group Scanning 10 Receiving a Signal on a Group Scan Channel 10 Removing Open Scan Channels 11 Reinstalling Channels into the Scan Group 12 Selective Ca
Streszczenie treści zawartej na stronie nr. 3
Contro 15/1 nd icators/Con nactio ns Front Panel Controls @ @ unldl!l1 SCAN OSIGS UH-099 ID CALMEMCUPTSQ " " DD SRF os - - ,-,,.,,j ,-,,-,,-, GS l l 1 1 MEM 000.000 11HzPII SCN - - D' L..ENT-' oLJ L ' L..~-' Oo~ ~ @) @ G) @ @ rJ) @ @ CD 1. CHANNEL SELECTOR Selects the desired channel for transmission and reception. 2. SCAN CONTROL (SCAN) Scans channels programmed in the selected SCAN mode. NOTE: The radio will not scan if the selected Scan Memory has not been programmed. 3. OPEN SCAN/GROUP SCAN
Streszczenie treści zawartej na stronie nr. 4
8. SQUELCH CONTROL Eliminates received background noise in the absence of an incoming signal. Turn the control knob fully counter-clockwise and then slowly rotate clockwise until the received noise is eliminated. 9. VOLUMECONTROL Turns the radio on and increases the volume level when turned clockwise. Decreases the volume level and turns the radio off when turned counterclockwise. 10. MICROPHONE SOCKET The microphone plug is inserted into this socket. 11. LIQUID CRYSTAL DISPLAY (LCD) Uses severa
Streszczenie treści zawartej na stronie nr. 5
Microphone 1 2 1. PRESS- TO-TALK Button Use the PRESS- TO-TALK button on the microphone to receive and transmit. Press the button to activate the transmitter and release the button to receive. When transmitting, hold the microphone about two inches from your mouth and speak clearly in a normal voice. 2. TONE CALL CONTROL (CALL) Button Use the TONE CALL CONTROL (Call) button to check, edit, or transmit the TX Selcalll D. Press the button once and the Selcalll D will be displayed. Under this condi
Streszczenie treści zawartej na stronie nr. 6
Back Panel IIXI'... ~ (8) 3 1. EXTERNAL SPEAKER JACK (EXT.SP) Usedfor remote receiver monitoring. When the external speaker is connected the internal speaker is automatically disconnected. 2. POWER DC power is connected to the transceiver through this jack. A power cord is supplied with the transceiver. 3. ANTENNA CONNECTOR (ANT) The transmission line cable plug connector (M-type) is connected to the transceiver through this antenna connector socket. Page 5
Streszczenie treści zawartej na stronie nr. 7
Getting Started Mobile Station Installation Select the location of the transceiver and microphone bracket before starting the installation. The location should be convenient and should not interfere with the driver or passenger in the vehicle. The transceiver should be securely fastened to a solid face, using the mounting bracket and self-tapping screws which are provided. Choosing an Antenna Since the maximum allowable power output of the transmitter is limited by the Spectrum Management Agency
Streszczenie treści zawartej na stronie nr. 8
Operation How to Receive 1. Confirm that the power source, antenna, and microphone are connected properly before proceeding to the following steps. 2. Turn the unit ON by rotating the VOLUME control clockwise. 3. Set the CHANNEL CONTROL knob to the desired channel. 4. Set the VOLUME control to a comfortable listening level. 5. Listen to the background noise from the speaker. Turn the SQUELCH control slowly clockwise just until the noise is eliminated (no signal should be present). Leave the cont
Streszczenie treści zawartej na stronie nr. 9
Scanning Pressing the SCAN button one time will initiate scanning, and scanning is stopped either by pressing the button a second time or pressing the Press-to- Talk button. Programming Scan Channels When the radio is initially turned on, there will not be any channels programmed in the Group Scan Memory. To Program scan channels into the Group Scan Memory, use the following proce- dure: 1. Select the NORMAL mode (or when scanning, cancel scanning by pressing the SCAN button.) 2. Select the GROU
Streszczenie treści zawartej na stronie nr. 10
Removing Group Scan Channels To Delete a programmed channel from the Group Scan Memory, use the following procedure: 1. Rotate the CHANNEL SELECTOR knob until the channel you wish to remove is displayed. Note that the MEM indicator should appear, indicating that this channel is currently programmed in memory. 2. Press and hold the MEM button for about 1.5 seconds until a beep is heard twice. The MEM indicator should now be off. Select Remove 'MEM' Icon CHANNEL CHANNEL OFF MEM I81Iden D UII + GS
Streszczenie treści zawartej na stronie nr. 11
Group Scanning Tocommence GROUP SCANNING, select the GROUP SCAN modeby pressing the OS/GS button when in the OS mode, and select the SCAN mode by momentarily pressing the SCAN button. The SUNDOWNER UH-O99will now scan the programmed channels, displaying each channel number and the PRIORITY channel number. Before it scans each channel, it quickly "checks" the PRIORITY channel (set by the CHANNEL SELEC- TOR). NOTE: 1. In the GS mode, the starting channel prior to GS Memory Scanning is always set a
Streszczenie treści zawartej na stronie nr. 12
Removing Open Scan Channels When the radio is initially turned on, all 40 channels are programmed in the OPEN SCAN MEMORY. If you do not wish to scan some particular channels (e.g. if one or more channels are continually busy and always causing the scanning function to pause), you can remove these channels from the scan group by using the following procedure: 1. Cancel scal)ning (if active). 2. Select the OPEN SCAN mode by pressing the OS/GS button when in the GS mode. The OS indicator should ap
Streszczenie treści zawartej na stronie nr. 13
Reinstalling Channels into the Scan Group To reinstall previously deleted channels into the scan group, simply repeat steps 3 and 4. However, this time note that a beep will be heard when the MEM button is pressed, and the MEM indicator will light, indicating that the selected channel is now included in the scan group. Reinstall 'MEM' Icon Select CHANNEL ON CHANNEL , I , ,.. ~E~- MEM I81kII!n 11' lJH.O99 os U" "-' 1 ) t BEEPI'" (0) When finished, rotate the CHANNEL SELECTOR dial and notice that
Streszczenie treści zawartej na stronie nr. 14
Selective Calling Outline Selective Calling (SELCALL) is a special Sequential Tone Squelch System that allows the user to receive/transmit calls selectively from/to an individual or a group, on a shared busy channel. The SUNDOWNER UH-O99 has a specially built-in Selective Calling (SELCALL) system. Exceptional features like Receiver Quieting,Tone Squelch Scanning, Tone and Group Calling make the SUNDOWNER UH-O99superior to any transceivers in its class. Receiver Quieting (Tone Squelch) When activ
Streszczenie treści zawartej na stronie nr. 15
Receiver Quieting Puts the receiver in the "Ouiet" mode (also known as the "Tone Squelch" mode). When activated, the transceiver prevents any unwanted conversations in the channel from being heard unless the call is specifically directed to you and the SELCALL ID required to open the "Ouiet" condition has been received. To activate: 1. Select the channel you want to put in Quiet mode using the Channel Selector knob. 2. Press the T.SO button for about 1.5 seconds. One beep is heard and the T.Sa i
Streszczenie treści zawartej na stronie nr. 16
Start the T.Sa Scan by pressing the T.Sa button during Open Scan or Group Scan. Unlike Normal Scanning, T.Sa Scanning checks the detected carrier for SELCALL information. If this information is not found, T.Sa scanning resumes. When a call is received during T.Sa Scanning, UH-099 follows the same response as when receiving a call on a Tone Squelch Channel. It differs only in the following ways. 1. If the call is not answered within the 20 second period, T .sa Scanning resumes. The CAL indicator
Streszczenie treści zawartej na stronie nr. 17
1. Select the channel that you and your group agreed to use for Selective Calling. 2. Press and hold the Tone Call Button for about 1.5 seconds. One long beep will be heard and the CAL indicator will appear on the LCD display while the SELCALL ID is being transmitted automatically. An Acknowledge Tone coming from the called radio will be received if you had successfully made contact. The Acknowledge Tone for the SUNDOWNER UH-099 is a succession of three Low Tone Beeps. 5/6 Tone TX SELCALL Progra
Streszczenie treści zawartej na stronie nr. 18
Assign a SELCALL number on this position. Follow procedure 1.1 for further TX SELCALL ID editing. When finished, press I MEM I or transmit the code ENT to save the new setting onto memory. 1.22 From 6 to 5 Tone Format Setting Select the 6th digit position, change the setting from the assigned SELCALL number to a space bar [-]. Example MEM 11 L1 S 1:"1-. _,11 os l I - le-tUC"i""" ..J '-"".0.,- To MEM 11 LA S ,1/ - c" ...- os l I - '~-IY, ,- '1..- -~ Follow procedure 1.1 for further TX SELCALL edi
Streszczenie treści zawartej na stronie nr. 19
TX SELCALL ID Format To call Transmitter SELCALL ID 10 radios [xl [xl [xl [xl [AJ 100 radios [xl [xl [xl [AJ [AJ 1000 radios [xl [xl [AJ [AJ [AJ 10000 radios [xl [AJ [AJ [AJ [AJ where: [xl is a common SELCALL ID prefix of your group and, [AJ is the CCIR Assigned Group Tone Code example: If one group comprises 10 members with SELCALL IDs. ranging from [1 J [2J [3J [4J [0], [1J [2J [3J [4J [1], [1J [2J [3J [4J [2], [1J [2J [3J [4J [3J, to [1J [2J [3] [4J [9], All in T.SQ mode at CH20. If someone t
Streszczenie treści zawartej na stronie nr. 20
5/6 TONE SELCALL PROGRAMMING Since UH-O99can support either a 5 or 6 tone signalling format, you and your group must decide which format to use. The following is a basic outline of SELCALL Programming. Press and Hold ITSQ I on Power ON RECEIVER CODE PROGRAMMING Press ITSQI Press ITSQ I TONE PERIOD PROGRAMMING Press I TSQ I ALARM MODE PROGRAMMING LEAD-IN DELAY PROGRAMMING Press ITSQI Press I TSQ I LEAD-IN TONE PROGRAMMING To select, press IMEM I ENT To save new a setting after programming, press
