Instrukcja obsługi Sanus Systems VISIONMOUNT VMDD26

Streszczenie treści zawartej na stronie nr. 1

VMDD26
Thank you for choosing the Sanus Systems VisionMount™ VMDD26. It mounts most flat panel televisions up to 1600 cm (63 in),
tilts the TV +5° to -15°, swivels ± 75°, rolls ± 6°, and extends 654 mm (25.75 in) from the wall.
WARNING
Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may
cause property damage or personal injury. If you do not understand these directions, or have doubts about the
safety of the installation, contact Sanus

Streszczenie treści zawartej na stronie nr. 2

[08] x 1 [09] x 20 [07] x 1 5/16 in. [10] x 14 [11] x 4 [12] x 4 1/4-20 x 2.0 in. 5/16-18 x 1 in. 1/4-20 [13] x 4 [14] x 4 [15] x 3 [16] x 4 M4 x 12mm M5 x 12mm M6 x 12mm M8 x 16mm [17] x 4 [18] x 4 [19] x 4 [20] x 4 M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm [21] x 4 [22] x 4 [23] x 4 [24] x 4 M4 M5 M6 M8 [25] x 4 [26] x 4 [27] x 4 [28] x 4 M4 / M5 M6 / M8 M4 / M5 M6 / M8 [29] x 4 [30] x 4 [31] x 8 [32] x 4 6901-100015 <01> 2

Streszczenie treści zawartej na stronie nr. 3

M8 x 16mm 1 Determine the Bolt diameter required — [17] / [21], [18] / [22], [19] / [23], or [20]/ [24] — by threading each size into the back of the TV. Stop immediately if you encounter any resistance. 1-1: TV with flat back 1-2: TV with curved back or obstruction 1-1 1-2 [31] [17] [29] [31] [31] [25] [21] [25] M4 x 30mm M4 x 12mm [29] [31] [31] [26] [22] [31] [26] [18] M5 x 12mm M5 x 30mm [32] [27] [19] [30] [—] [32] [27] [23] M6 x 12mm M6 x 35mm [32] [28] [20] [30] [—] [32] [28] [24] M8 x 4

Streszczenie treści zawartej na stronie nr. 4

2 Do not overtighten the Nut [14]. The Vise Assembly [06] should rotate freely around the Carriage Bolt [13]. [06] [13] 4x [14] [05] 3 [04] [05] [04] 2x [06] 6901-100015 <01> 4

Streszczenie treści zawartej na stronie nr. 5

4 CAUTION To prevent property damage or injury from an unstable installation, extend the Tubes [04] beyond the outside edges of both Monitor Brackets [05] and tighten the Allen Bolts on Vise Assemblies [06] and [A] of the Arm Assembly [02]. Do not overtighten Vise Assemblies [06] and [A]. Turn the Allen Bolt until resistance is felt. Then tighten the Bolt about 1½ turns, or until it is slightly above the surface of the Vice Assembly. The Tubes [04] will not move from side to side if the Vis

Streszczenie treści zawartej na stronie nr. 6

6 CAuTIoN To prevent property damage or personal injury, tighten each Lag Bolt [11] only until the Wall Plate [01] is pulled firmly against the wall. The drywall or other wall material may not exceed 15.8 mm (5/8 in) in thickness. 4x [01] [11] [12] 7 CAuTIoN To prevent property damage or personal injury, all Safety Bolts [15] must be securely tightened. [02] [15] [01] 3x 6901-100015 <01> 6

Streszczenie treści zawartej na stronie nr. 7

8 Set the tilt tension with the Knobs [K] on the Arm Assembly [02]. The TV freely tilts +5° to -15° without further Knob adjustment. To change the roll ± 6°, loosen the Allen Bolts [B] on the Arm Assembly, position the TV, and retighten the Allen Bolts. [02] [02] K B 9 CAuTIoN To prevent property damage, do not remove the Tension Nuts [T] or fail to reinstall the Safety Bracket [S]. To adjust tension on the Arm Assembly [02], loosen or tighten the Tension Nuts [T]. For the Tension Nuts closes

Streszczenie treści zawartej na stronie nr. 8

10 CAUTION To avoid injury, do not place your hands or fingers between moveable parts. [03] [16] 2x 11 Leave some slack in the cables to prevent excess tension on the connectors. Do not run cables through any pinch points. Wire Tie Clips [10] can be pressed into holes on the top and bottom of the Arm Assembly [02] or sides of the Preventor [03]. Wire Ties [09] may be threaded through the Wire Tie Clips or holes in the Monitor Brackets [05] to secure the cables. [10] [05] [02] [03] CSAV, Inc. a