Instrukcja obsługi Metra Electronics 99-7878B

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7878B
APPLICATIONS
HONDA Insight
2010
99-7878B
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted A Matte Black Finish
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
A
B C D
E
F
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillip

Streszczenie treści zawartej na stronie nr. 2

99-7878B TABLE OF CONTENTS Dash Disassembly - Honda Insight 2010 . ... ... .... ... .... ... .... ... .... .1,2 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 - Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6 Note: Ref

Streszczenie treści zawartej na stronie nr. 3

95-7878B DASH DISASSEMBLY HONDA INSIGHT 2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the pocket/acces- sory socket panel below the factory radio. (Figure A) 3 Remove (1) 8 MM bolt facing up behind panel. Figure B) 4 Open the glove box then use a small blunt tool (ie: the wooden handle of a B hammer) to put pressure on the back of the radio chassis to unclip and remove the radio. (Figure C) Continued on page 2. C 1 OFF FRONT REAR

Streszczenie treści zawartej na stronie nr. 4

95-7878B DASH DISASSEMBLY HONDA INSIGHT 2010 5 Remove (2) Phillips screws securing the hazard switch to the back of the factory radio panel. (Figure D) 6 Remove (2) Phillips screws securing the air bag light to the back of the factory radio panel. (Figure D) 7 Remove the (8) retaining clips from the factory radio panel. (Figure D) Continue to kit preparartion. D 8 RETAINING CLIPS HAZARD SWITCH TWO SCREWS AIR BAG SWITCH TWO SCREWS 2

Streszczenie treści zawartej na stronie nr. 5

99-7878B KIT PREPARATION KIT PREPARATION 1 Secure the hazard switch into the radio housing panel using the factory hardware. (Figure A) 2 Secure the air bag light into the radio housing panel using the factory hardware. (Figure A) Attach the (8) retaining clips to the radio housing panel in the same location as 3 removed from the factory radio panel. (Figure A) Continue to kit assembly. A 8 RETAINING CLIPS HAZARD SWITCH TWO SCREWS AIR BAG SWITCH TWO SCREWS 3

Streszczenie treści zawartej na stronie nr. 6

99-7878B KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Snap the pocket into the bottom B opening of the rad

Streszczenie treści zawartej na stronie nr. 7

99-7878B KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Snap the pocket into the bottom B opening of the radio housing. (

Streszczenie treści zawartej na stronie nr. 8

99-7878B KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing. (Figure A) 3 Snap the Double DIN brackets to the B inside edge of the Double DIN trim