Instrukcja obsługi Metra Electronics 99-8712

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8712
APPLICATIONS
Mercedes Benz C Class
2005-2007
99-8712
KIT FEATURES
• DIN head unit provision with pocket
KIT COMPONENTS
A) Radio Housing
Antenna Adapter:
• 40-VW12 - Mercedes antenna adapter
A
TOOLS REQUIRED:
Socket Wrench • Torx Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 10-07-10

Streszczenie treści zawartej na stronie nr. 2

99-8712 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.

Streszczenie treści zawartej na stronie nr. 3

F 72 72 F 80 64 80 64 FRONT AUTO A/C REAR F F 72 72 80 64 80 64 FRONT AUTO A/C REAR F 72 72 F 80 64 64 80 AUTO A/C FRONT REAR ESP ESP OFF OFF 3 2 4 5 6 3 2 4 5 6 3 2 4 5 6 99-8712 DASH DISASSEMBLY 2005-2007 MERCEDES BENZ C CLASS A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove cover around shift lever and cup holder. (Figure A) 3 Unclip and remove ashtray assembly. (Figure B) 4 Remove (2) Torx screws from the B bottom of the climate contro

Streszczenie treści zawartej na stronie nr. 4

ESP OFF 99-8712 DASH DISASSEMBLY 2005-2007 MERCEDES BENZ C CLASS D 5 Using a small screwdriver push the release clips inside the vents inward and rotate the vents upward to expose the (2) Torx screws behind the vents. (Figure D) 6 Unclip and remove the vent assembly. (Figure E) 7 Remove (4) Torx screws securing factory radio then remove the unit. E (Figure F) F 2

Streszczenie treści zawartej na stronie nr. 5

99-8712 KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket head unit into 2 the cage and secure. (Figure B) B 3

Streszczenie treści zawartej na stronie nr. 6

99-8712 FINAL ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA c

Streszczenie treści zawartej na stronie nr. 7

99-8712 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 10/07/10 INST99-8712