Instrukcja obsługi Transition Networks CSEFE10XX-10X

Streszczenie treści zawartej na stronie nr. 6

CSEFE10xx-10x Contact Us Troubleshooting -- Continued Technical Support 6. Is the TP-ACT LED illuminated? Technical support is available 24 hours a day. NO US and Canada: 1-800-260-1312  Check the twisted-pair copper cables for proper connection. International: 00-1-952-941-7600  Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600. YES Transition Now  Go to step 7. Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transiti

Streszczenie treści zawartej na stronie nr. 7

Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi

Streszczenie treści zawartej na stronie nr. 1

User’s Guide
CSEFE10xx-10x
Slide-in-Module Media Converter
• Switchable Ethernet and Fast Ethernet
 10 Mb/s Copper to Fiber
 100 Mb/s Copper to Fiber
Transition Networks CSEFE10xx-10x series Ethernet /
Fast Ethernet media converter is designed to be
installed in a Transition Networks PointSystem™
chassis and is a 10Mbps or 100Mbps switch-selectable
media converter.
Both the copper and fiber links operate at the same speed setting via a hard set with
a dip switch, so the media converter oper

Streszczenie treści zawartej na stronie nr. 2

CSEFE10xx-10x Installation Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge Set the Speed (switch 2) Link Pass-Through: up = Enable precautions when setting the jumper or when installing the media converter. Switch 2 sets the speed for both the twisted-pair Speed: up = 100 Mb/s Failure to observe this caution could result in damage to, and subsequent copper and fiber links: failure of, the media converter. up = copper and fiber links are at 100Mb/s.

Streszczenie treści zawartej na stronie nr. 3

CSEFE10xx-10x Installation -- Continued Operation Install the Fiber Cable Status LEDs PWR The CSEFE10xx-10x is designed to be installed in pairs over the fiber link, Use the status LEDs to monitor the CSEFE10xx-10x media ACT 100 10 where one is the local media converter and the other is the remote. converter operation in the network. F 1. Locate or build fiber-optic cable with male, two-stranded TX to RX TP PWR Power On = Connection to the external AC connectors installed at both ends. TX

Streszczenie treści zawartej na stronie nr. 4

CSEFE10xx-10x Operation -- Continued Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. SNMP Fiber Cable Use SNMP at an attached terminal or at a remote location to monitor the media converter by monitoring: -9 Bit Error Rate: <10  Media converter power Single mode: 9 µm  Copper link status  Fiber link status CSEFE1012-100 1310 nm single mode Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm  Copper receive status Fiber-optic Recei

Streszczenie treści zawartej na stronie nr. 5

CSEFE10xx-10x Technical Specifications Troubleshooting For use with Transition Networks Model CSEFE10xx-10x or equivalent. 1. Is the PWR LED on the media converter illuminated? Standards: IEEE 802.3™, 10Base-T, 100Base-TX, 100Base-FX NO Data Rate: 10 Mb/s, 100 Mb/s  Is the media converter inserted properly into the chassis?  Is the power cord properly installed in the chassis and in the Dimensions: 3.4" x 0.87" x 5" (86 mm x 22 mm x 182 mm) grounded AC outlet? Weight: 3 oz (91 g) (approximat