Streszczenie treści zawartej na stronie nr. 1
¨
METROBILITY
FOUR-PORT SWITCH
10/100 BASE
PWR
LK
1
AT
LK
2
AT
LK
3
AT
4 LK
AT
Installation & User Guide
Model: R104-11
Streszczenie treści zawartej na stronie nr. 2
Metrobility Four-port Switch R104-11 ____ 10/100Mbps Four-Port TX Switch This publication is protected by the copyright laws of the United States and other countries, with all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, translated, transcribed, or transmitted, in any form, or by any means manual, electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without prior explicit written permission of Telco Systems. © 2006 Te
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Metrobility 4-port Switch Installation & User Guide Overview .............................................................................................................. 4 Installation Guide ............................................................................................... 5 STEP 1: Unpack the Line Card .............................................................. 5 STEP 2: Set the Switches .......................................................................
Streszczenie treści zawartej na stronie nr. 4
¨ Overview The Metrobility R104-11 is a four-port 10/100Mbps TX switch that provides a cost-effective solution for situations in which a simple switching option with few ports is required. When configured for stacking in a Metrobility chassis, the card eliminates the need for any external equipment. This means the network administrator has one less piece of networking hardware to manage and monitor. The R104 is designed to support a stack of up to four R5000 chassis, thus enabling communication
Streszczenie treści zawartej na stronie nr. 5
1 2 3 4 -----------OPEN----------- ---------------------- OPEN ---------------------- 1 2 3 4 5 6 Installation Guide Follow the simple steps outlined in this section to install and start using the R104. NOTE: Electrostatic discharge precautions should be taken when handling any circuit board. Proper grounding is recommended (i.e., wear a wrist strap). Unpack the Line Card Your order has been provided with the safest possible packaging, but
Streszczenie treści zawartej na stronie nr. 6
* When setting DIP switches on SW2, the OPEN position is when the lever of the switch is pushed up toward the word “OPEN.” The CLOSED position is when the lever is pushed down toward the board. On the rocker DIP switch (SW1), the OPEN position is when the “OPEN” side of the switch is down and the numbered side is up. The CLOSED position is when the numbered side of the switch is down and the “OPEN” side is up. See illustration below. HDFL HDFL FD FD AN1 AN1 100M1 100M1 OPEN CLOSED Auto-Negotiati
Streszczenie treści zawartej na stronie nr. 7
Duplex Switch (FD) Switch FD determines the duplex mode on all ports that have auto- negotiation disabled. • The ports will operate at full duplex if FD is OPEN. (default) • They will operate at half duplex if FD is CLOSED. If auto-negotiation is enabled on a port, that port will ignore the FD switch setting. For example, if FD is enabled and auto-negotiation is disabled on Ports 1 and 2 and enabled on Ports 3 and 4, then Ports 1 and 2 will operate at full duplex, while Ports 3 and 4 will ignore
Streszczenie treści zawartej na stronie nr. 8
The table below displays sample port configurations and the DIP switch settings used to obtain them. The configuration column gives the auto- negotiation, speed and duplex options for each port. By default, all four ports are set to auto-negotiate. C1 onfiguration P2 ort P3 ort P4 ort Port P2 ort 1P3 ortP4 ortPD ort F1A1 N12 00MA2 N13 00MA3 N14 00MA4 N 100M AN AN AN AN + + + + AN N ANAl1+ 00 Ful + + + — + AN AN AN 100 Half — + + + — + AN N ANAl1+ 0 Ful + + + — — AN AN AN 10 Half — + + + — — AN N
Streszczenie treści zawartej na stronie nr. 9
Install the Card The R104offers the ease of plug-and-play installation and is hot- swappable. The unit must be firmly secured to the chassis before 3 network connections are made. Follow the simple steps outlined below to install the card. • Grasp the card by the front panel as shown. Slot for Management Card Card Guide 10/100 10/100 10/100 10/100 OC-12 1000BASE 1000BASE OC-12 10/100 10/100 10/100 10/100 10/100 OC-12 OC-12 OC-12 PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR PWR MGT
Streszczenie treści zawartej na stronie nr. 10
Connect to the Network To connect the R104 to the network, insert the twisted-pair cables into the appropriate connectors. Be sure the card is secured to the chassis by 4 tightening the thumbscrew before making network connections. The R104 provides four shielded RJ-45 connectors that support a maximum segment length of 100 meters. Use Category 3, 4 or 5 cables for 10Mbps segments; use only Category 5 or 5E cables for 100Mbps segments. Insert your connectors as shown below. Once power is applied
Streszczenie treści zawartej na stronie nr. 11
User Guide This section contains information regarding the operating features of the Metrobility R104. LED Indicators The R104 provides several LEDs for the visible verification of unit status and proper functionality. These LEDs can assist in troubleshooting and with overall network diagnosis and management. There are separate link/speed and activity/ duplex indicators for each port. After power is applied to the card, verify correct connectivity via the LK LEDs. LED LED Indication LabelN) ame
Streszczenie treści zawartej na stronie nr. 12
Technical Specifications Network Connections Twisted-Pair Interface Connector __________________________________ Shielded RJ-45, 8-pin jack Impedance________________________________________ 100 Ohms nominal Signal Level Output (differential) ________________ 0.95 to 1.05V (100Mbps) ___________________ 2.2 to 2.8V (10Mbps) Signal Level Input ________________________ 200mV minimum (100Mbps) __________________________________ 585mV (10Mbps) Supported Link Length ____________________________________
Streszczenie treści zawartej na stronie nr. 13
Product Safety, EMC and Compliance Statements This equipment complies with the following requirements: •UL • CSA •CE •CB • FCC Part 15, Class A • EN55022 Class A (emissions) • EN55024: 1998 (immunity) • ICES-003 Class A (emissions) This product shall be handled, stored and disposed of in accordance with all governing and applicable safety and environmental regulatory agency require- ments. The following FCC and Industry Canada compliance information is applicable to North American customers only
Streszczenie treści zawartej na stronie nr. 14
Warranty and Servicing Telco SystemsÕ Product Warranty TELCO MAKES NO WARRANTIES EXCEPT AS HEREIN SET FORTH: Telco warrants that the equipment and accessories manufactured by Telco, when used in the application and manner for which they are intended, will be free from defects caused by faulty material or poor workmanship from the date of shipment. This warranty is subject to change at any time. The warranty that applies is that which is in effect at the time the equipment ships. Warranty period
Streszczenie treści zawartej na stronie nr. 15
Replacement, Repair or Refund Procedure for Hardware: TelcoÕs sole obligation under this express warranty shall be, at TelcoÕs option and expense, to repair the defective product or part or deliver to Customer an equivalent product or part to replace the defective item. All products that are replaced will become the property of Telco Systems. Replacement products or parts may be new or reconditioned. Telco warrants any replaced or repaired product or part for ninety (90) days from shipment, or t
Streszczenie treści zawartej na stronie nr. 16
US Headquarters 2 Hampshire Street Suite 3A Foxboro MA USA 02035 tel: 1.781.551.0300 ¥ fax: 1.781.255.2344 www.telco.com 5660-000023 D 12/06
