Streszczenie treści zawartej na stronie nr. 1
Specialized Models User Guide 6 MPLS Model User Guide
6 MPLS Model User Guide
Multi-Protocol Label Switching (MPLS) is a multi-layer switching technology that
uses labels to determine how packets are forwarded through a network. The
first part of this document describes key features of the MPLS specialized model
and the second part focuses on procedures for configuring MPLS in your
network model.
Model Features
This section contains a list of the main features available in the Multi-Protocol
Streszczenie treści zawartej na stronie nr. 2
Specialized Models User Guide 6 MPLS Model User Guide MPLS models are implemented based on information available from the following sources. Table 6-2 Reference Documents Model Features Document Traffic Engineering MPLS TE RFC-2702—Requirements for Traffic Engineering Over MPLS FECs RFC-3031—Multiprotocol Label Switching Architecture IGP shortcuts draft-hsmit-mpls-igp-spf-00 Label Switched Paths Dynamic LSPs RFC-3031—Multiprotocol Label Switching Static LSPs Architecture LSP routing OSP
Streszczenie treści zawartej na stronie nr. 3
Specialized Models User Guide 6 MPLS Model User Guide Node Models The MPLS model suite supports workstation, server, router, and link models from the standard model library. The LER (Label Edge Router) and LSR (Label Switching Router) node models in the MPLS object palette are preconfigured to support MPLS. However, you can configure any of the router models in the standard model library to model LERs and LSRs. Figure 6-1 MPLS Object Palette Model Attributes Global MPLS attributes, which a
Streszczenie treści zawartej na stronie nr. 4
Specialized Models User Guide 6 MPLS Model User Guide Figure 6-2 Specifying FEC Attributes The FEC Details Table helps define the FEC through a set of match rules, which are combinations of TCP, UDP, and IP header fields. FECs are determined by taking a logical AND of the column settings in a row and by taking a logical OR of each of the rows. In other words, for a packet to qualify for a particular FEC, the IP header fields must satisfy every condition of at least one row of the defined
Streszczenie treści zawartej na stronie nr. 5
Specialized Models User Guide 6 MPLS Model User Guide LSP Specification File This attribute indicates whether the network LSPs should be configured according to the text file specified. You can update the text file by clicking OK in the LSP Browser. Updating the file recreates the file based on the current network LSP settings, including LSPs that might not have been in the original file (such as those created manually). Traffic Trunk Profiles This attribute specifies out-of-profile acti
Streszczenie treści zawartej na stronie nr. 6
Specialized Models User Guide 6 MPLS Model User Guide Figure 6-5 Mapping EXP Bits to Drop Precedence and PHB Router Attributes Some of the important MPLS Parameters attributes set on routers are described below. Traffic Mapping Configuration This attribute specifies bindings between FECs and LSPs. Each row of the Traffic Mapping Configuration table specifies a distinct traffic engineering (TE) binding. Each TE binding specifies the FEC, traffic trunk, and LSP that is applied to the label o
Streszczenie treści zawartej na stronie nr. 7
Specialized Models User Guide 6 MPLS Model User Guide When an unlabeled packet arrives at an ingress LER, the following sequence occurs to determine the correct label for the packet: 1) The TE binding is selected based on the packet FEC and the incoming interface. 2) The packet is checked to make sure that its traffic characteristics conform to those specified for the TE binding’s traffic trunk. 3) The packet is labeled for and sent through the primary LSP specified for the TE binding. Figur
Streszczenie treści zawartej na stronie nr. 8
Specialized Models User Guide 6 MPLS Model User Guide Figure 6-7 Configuring LDP Parameters Simulation Attributes The following simulation attributes are available (Configure/Run Discrete Event Simulation dialog box) when using the MPLS model suite. CR-LDP Routing—specifies if CR-LDP routing uses CSPF or conventional IGP to determine routes in loosely defined LSPs. The default value is IGP. CSPF Retry Timer—specifies how long an ingress LER waits after detecting a node or link failure b
Streszczenie treści zawartej na stronie nr. 9
Specialized Models User Guide 6 MPLS Model User Guide LSP Attributes Some of the important LSP attributes are described below. Most of these attributes can also be configured in the LSP browser, which is described in the next section. Figure 6-8 Configuring an LSP’s Attributes Directionality—specifies if an LSP is unidirectional or bidirectional. Dynamic LSPs are always unidirectional. LSP Type—specifies whether the LSP is of type E-LSP or L-LSP. For E-LSP, three experimental bits in t
Streszczenie treści zawartej na stronie nr. 10
Specialized Models User Guide 6 MPLS Model User Guide Figure 6-10 Recovery Parameters Configuration Setup Parameters—specifies the duration of the LSP. Figure 6-11 Setup Parameters Configuration TE Parameters—specifies the traffic engineering constraints used by CR-LDP to find a route through the network. CR-LDP uses Constrained Routing to find the route that is the best fit for the specified constraints. This attribute applies to dynamic LSPs only. Make sure you account for network
Streszczenie treści zawartej na stronie nr. 11
Specialized Models User Guide 6 MPLS Model User Guide LSP Browser After you create the LSPs in the network, you may want to edit or view the default settings. You do this in the LSP browser, which you can access from the Protocols > MPLS > Browse/Edit LSP Information... menu item. The browser enables you to Set the hop type of LERs Set the start and end times for the LSP Set threshold values for bandwidth, delay, and hop counts in the LSP Hide some or all of the LSPs from view in the
Streszczenie treści zawartej na stronie nr. 12
Specialized Models User Guide 6 MPLS Model User Guide Available Statistics To analyze MPLS performance, you can collect path statistics on end-to-end delay, utilization, and the amount of traffic on the LSP. These statistics can be collected on a per-flow or per LSP basis, where flows are individual flows of traffic within an LSP. Figure 6-14 Selecting Statistics to Collect When analyzing your MPLS network, you may also want to look at the routes used for the LSPs. You can do this by selec
Streszczenie treści zawartej na stronie nr. 13
Specialized Models User Guide 6 MPLS Model User Guide Configuring MPLS in a Network Configuring MPLS in a network is a three-step process. Before you can run a simulation using MPLS, you must 1) Create LSPs in the network topology 2) Create FECs and traffic trunks in the MPLS Configuration object 3) Configure LERs to direct packets into the appropriate LSPs After this basic configuration is in place, you can add QoS/differentiated services (DiffServ) constraints or traffic shaping parameters.
Streszczenie treści zawartej na stronie nr. 14
Specialized Models User Guide 6 MPLS Model User Guide 2 If you have not assigned IP addresses to all connected interfaces in the network, click the “Perform Auto-Assignment” button. Otherwise, click the “Skip Auto-Assignment” button. ➥ The MPLS Configuration dialog box opens. This box shows all the traffic pairs configured in the network with suggested configuration for LSP configuration. 3 In the MPLS LSP Configuration dialog box, specify which traffic conversation pairs should not generate
Streszczenie treści zawartej na stronie nr. 15
Specialized Models User Guide 6 MPLS Model User Guide Constrained OSPF (CSPF) is used to implement constraint-based routing of LSPs. You can configure dynamic LSPs to use constraint-based routing in the LSP’s TE Parameters attribute by setting the Bandwidth, Delay, and Hop Count constraints. When using TE constraints, the model must be configured to use (CSPF) as follows: The CR-LDP simulation attribute must be set to CSPF The IP routing protocol must be set to OSPF (You can set the dyn
Streszczenie treści zawartej na stronie nr. 16
Specialized Models User Guide 6 MPLS Model User Guide Creating FECs and Traffic Trunks The traffic engineering bindings that govern how packets are labeled and forwarded in a network use FECs and traffic trunks to classify packets. All of the FECs and traffic trunks in a network are defined in the MPLS configuration object. Procedure 6-4 Creating FECs 1 Place an MPLS configuration object in the project workspace and open its Attributes dialog box. 2 Double-click on the value for FEC Specif
Streszczenie treści zawartej na stronie nr. 17
Specialized Models User Guide 6 MPLS Model User Guide Creating TE Bindings on LERs After you create the LSPs, FECs, and traffic trunks, you can create TE bindings that govern which packets are sent to which LSPs. You do this in the LER’s MPLS Parameters ➘ Traffic Mapping Configuration attribute. Procedure 6-6 Creating a TE Binding 1 Open the LER’s Traffic Mapping Configuration attribute dialog box (MPLS Parameters ➘ Traffic Mapping Configuration). 2 Add a row to the table. 3 Click in the “
Streszczenie treści zawartej na stronie nr. 18
Specialized Models User Guide 6 MPLS Model User Guide Exporting LSP Configuration Details for Use in Other Scenarios You can reuse LSPs that you have configured elsewhere by exporting the LSP configuration details to an ASCII file and using this file to create LSPs in the network. Procedure 6-7 Exporting LSP Configuration to an ASCII File 1 From the Protocols > MPLS menu, choose Browse/Edit LSP Information.... ➥ The LSP Browser appears. 2 Click Export to export the LSP configuration for all
Streszczenie treści zawartej na stronie nr. 19
Specialized Models User Guide 6 MPLS Model User Guide Applying QoS to an MPLS Network Model Differential Services (DiffServ) extensions can be used to apply quality-of-service constraints to your MPLS network model. To do this, you must configure QoS do the following: Specify traffic classes in the MPLS configuration object Adjust DSCP settings in the QoS configuration object Configure queuing schemes and profiles on the affected routers To use different traffic classes in your MPLS netw
Streszczenie treści zawartej na stronie nr. 20
Specialized Models User Guide 6 MPLS Model User Guide If you change the queuing scheme later, make sure you reset the queuing profile because the order of these steps is important. Figure 6-15 Configuring QoS on an LER Always set the Queuing Scheme before setting the Queuing Profile. SPM-6-20 Modeler/Release 10.0
