Streszczenie treści zawartej na stronie nr. 1
45609/45614
®
Z-Wave Certified
Wireless Lighting Control
On/Off Relay Switch
and 3-Way Switch Kit
Control the On/Off status of
permanently installed lighting,
fans and more!
©2009 Jasco
www.easyzwave.com
Made in China
Streszczenie treści zawartej na stronie nr. 2
® Z-Wave Certified Wireless Lighting Control On/Off Relay Switch and 3-Way Switch Kit Introduction Thank you for your purchase of a GE Z-Wave® control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-Wave enabled de- vices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one room or your entire house and whether you want to do it all
Streszczenie treści zawartej na stronie nr. 3
WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, also an uninten- tional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending upon the ap- pliance, these unattended or unintentional operation
Streszczenie treści zawartej na stronie nr. 4
Things to consider regarding RF range: • Each wall or obstacle (i.e.: refrigerator, big screen TV, etc.) between the remote or Z-Wave device and the destination device will reduce the maximum range by approximately 25-30%. • Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and plasterboard (drywall). • Wall mounted Z-Wave devices installed in metal junction boxes may suffer a significant loss of range (approximately 20%) since the metal box blocks
Streszczenie treści zawartej na stronie nr. 5
One of the ways to wire a two-switch/one-load circuit is to route the incoming power through the first switch, then to the second switch and then to the load. Although very common and by no means a standard, it is the easiest to convert to Z-Wave control. With this type of circuit, Switch 1 is replaced by the Z-Wave auxiliary switch and Switch 2 is replaced with the primary Z-Wave switch. The auxil- iary switch does not actually control the power; instead, it sends a momentary voltage sign
Streszczenie treści zawartej na stronie nr. 6
3-Way Wiring Schematic using one 45609 and one 45610 White (Neutral) Black Traveler - Colored (Not Green) (Load) Z-Wave Z-Wave 45610 45609 Green (Ground) Black (Line/Hot) 4-Way Wiring Schematic using one 45609 and two 45610’s Traveler - Colored (Not Green) Z-Wave 45610 White (Neutral) Black Traveler - Colored (Not Green) (Load) Z-Wave Z-Wave 45610 45609 Green (Ground) Black (Line/Hot) Red - Traveler White - Neutral Green - Ground Black – Load Black – Line / Hot (to light fixture) (from br
Streszczenie treści zawartej na stronie nr. 7
Single, Dual and Triple Gang Boxes Tabs Tabs When installing the 45609 in multiple gang boxes it may be necessary to break off one or both of the scored tabs on the front yoke. This does not affect the electrical rating of the 45609. Break at this line WARNING - SHOCK HAZARD Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. 1. Shut of
Streszczenie treści zawartej na stronie nr. 8
11. OPTIONAL for 3 or 4-way control): Connect the Traveler wire (usually Red) to the screw terminal marked TRAVELER. The other end of this Traveler wire connects to the TRAVELER screw terminal on the 45610 Auxiliary Switch. See the following section for information about wiring the 45610 Auxiliary Switch. 12. Insert Z-Wave Switch into the switch box being careful not to pinch or crush wires. 13. Secure the switch to the box using the supplied screws. 14. Mount the wall plate. 15. Reapply po
Streszczenie treści zawartej na stronie nr. 9
diagram. It can then be added to groups and/or lighting scenes and managed remotely to control the On/Off status of the connected lighting. Air Gap Switch The 45609 has an air gap switch on the lower left side (see diagram for location) to completely disconnect power to the load. Pull the air gap switch OUT to disconnect the power while replacing light bulbs and push it all the way back in for normal operation. The air gap switch must be all the way in for the switch to function and contro
Streszczenie treści zawartej na stronie nr. 10
• Once the switch is part of the network, the same basic procedure is used to add the switch to groups & scenes or change advanced functions. Refer to the primary controller’s instructions for details. Please Note: After a power failure, the 45609 switch returns to the last used state. ADVANCED OPERATION The following Advanced Operation parameters require that you have an advanced controller like the GE model 45601 LCD remote. Advanced remotes from other manufacturers may also be able to
Streszczenie treści zawartej na stronie nr. 11
Invert Switch If the switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”. • Parameter No: 4 • Length: 1 Byte • Valid Values = 0 or 1 (default 0) Restoring Factory Defaults All Configuration Parameters can all be restored to their factory default settings by using your primary controller to delete/reset the device. ™ Interoperability with Z-Wave Devices A Z-Wave™ ne
Streszczenie treści zawartej na stronie nr. 12
FCC U2Z45609 The Federal Communication Commission Radio Frequency Inter- ference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance w
Streszczenie treści zawartej na stronie nr. 13
SPECIFICATIONS ZW4001 Power: 120 VAC, 60 Hz. Signal (Frequency): 908.42 MHz. Maximum Loads: 600W, incandescent, ½ HP Motor or 1800W (15A) Resistive Range: Up to 100 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module. Operating Temperature Range: 32-104° F (0-40° C) For indoor use only. Specifications subject to change without notice due to continuing product improvement Z-Wave is a registered US trademark of Zensys A/S is a trademark of General Electric
