Streszczenie treści zawartej na stronie nr. 1
RGB 400xi xi xi xi xi Series Installation Guide
Wall Box-Mountable Interfaces with
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
Euro Channel versions
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01 Daisan DMJ Building 6F
Anaheim, CA 92805 3821 AH Amersfoort PM Industrial Building 3-9-1 Kudan Minami
68-636-03 Rev. B
USA The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0074 Japan
714.491.1500 +31.33.453.4040 +65.
Streszczenie treści zawartej na stronie nr. 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Extron Electronics warrants this product agains
Streszczenie treści zawartej na stronie nr. 3
Table of Contents About this Guide ....................................................................... 1 Installation Overview ............................................................. 1 UL Requirements ....................................................................... 2 Installation Procedures .......................................................... 2 Preparing the site and installing the wall box ....................... 3 Mounting the interface to the wall box ..................
Streszczenie treści zawartej na stronie nr. 4
Table of Contents, cont’d About this Guide This guide contains installation information for the Extron RGB 400 Series of interfaces. These interfaces are designed to fit into standard 2-, 3-, and 4-gang electrical wall boxes. The EC versions of these interfaces are designed to fit into a Euro Channel. The following models will fit the indicated wall box or channel: • RGB 460xi and RGB 472xi* – A standard, 2-gang electrical wall box. RGB 464xi, RGB 474xi, RGB 468 Mxi, and RGB 478 Mxi* – A
Streszczenie treści zawartej na stronie nr. 5
Introduction 3 Attach the cables. See “Front panel features and Preparing the site and installing the wall box cabling” and “Rear panel features and cabling” in the Choose a location that will allow cable runs without user’s manual specific to your product. interference. Allow enough depth for both the wall box and the cables. You may need to install the cables into the wall, Set the rear panel DIP switches. Use the “Rear panel 4 furniture, or conduits before installing the interface. feature
Streszczenie treści zawartej na stronie nr. 6
Installation, cont’d 5. Feed cables through the wall box punch-out holes, and nails or screws, leaving the front edge flush with the outer wall or furniture surface. The illustration applies to secure them with cable clamps to provide strain relief. all sizes of wall boxes. 6. Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate If attaching the wall box to wood, use four #8 or #10 shields with heat shrink, if needed. screws or 10-penny nail
Streszczenie treści zawartej na stronie nr. 7
Installation, cont’d 3. Mount the interface’s faceplate to the wall box with machine screws, as shown in the following illustration. Cable Clamp Backing Plate Euro Channel Installation Cable Extron RGB 464xi (Example) Mounting the interface to the wall box 4. Reconnect the power supply and restore power to the equipment. Euro Channel versions Backing Plate The RGB 460xi, RGB 468xi, RGB 472xi, and RGB 478xi are Euro Channel available in a Euro Channel (EC) version. The front and rear panel feat
Streszczenie treści zawartej na stronie nr. 8
Installation, cont’d If the image does not appear or there is no sound installing the optional AAP devices are built into its front panel and hex screws are provided with mini AAP devices, 1. Make sure that all the devices are powered on. so no additional screws will be needed. 2. Ensure that the connectors are wired correctly at both 1. Before any cables are attached to an AAP device, secure ends of the cables. Audio cables must be wired for an the optional AAP devices to the faceplate with th
Streszczenie treści zawartej na stronie nr. 9
Installation, cont’d Rack mount .................................. No, but wall or furniture mountable RGB 400xi xi xi xi xi Series Enclosure type ............................ Metal Enclosure dimensions — RGB 460xi, xi, xi, RGB 472xi xi xi xi, xi, xi xi Plate ................................... 4.5” H x 4.6” W (11.4 cm H x 11.7 cm W) (2-gang) Interface back enclosure . 2.7" H x 3.3" W x 1.1" D (6.9 cm H x 8.4 cm W x 2.8 cm D) (Depth excludes front panel connectors and controls.) Enclosure dim
Streszczenie treści zawartej na stronie nr. 10
Dimensions and Templates Cut-out Templates All the templates in this section are actual size. Also, they all include the recommended 0.1” (0.25 cm) clearance on all sides of the electrical wall box to allow room for the raised areas surrounding the knockouts. The dashed line in each template indicates the cut-out area for installing a wall box. If you plan to install the interface without a wall box, use the smaller cut-out area indicated by the dotted lines. Use the following templates as a g
Streszczenie treści zawartej na stronie nr. 11
A-4 RGB 400xi xi xi xi xi Series Installation Guide The light gray area represents the layout of the electrical box (3.75"H x 7.38"W) against the rear of the RGB 460xi Dual, RGB 468xi, or RGB 478xi front panel. RGB 460xi Dual, RGB 468xi, or RGB 478xi 4-gang Cut-out Template To install the interface without a wall box, use the cut-out area (2.80"H x 7.275"W) indicated by the dotted line. The dashed line indicates the cut-out area (3.95"H x 7.58"W) for installing the electrical wall box.
