Streszczenie treści zawartej na stronie nr. 1
User’s Manual
RGB 400 Series
Mountable Interfaces
68-364-01
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics Information
™
1230 South Lewis Street, Anaheim, CA 92805 Beeldschermweg 6C, 3821 AH Amersfoort 135 Joo Seng Rd. #04-01, PM Industrial Bldg. ExtronWEB : www.extron.com Printed in the USA
+31.33.453.4040 FAX +31.33.453.4050 +65.383.4400 FAX +65.383.4664 ExtronFAX™: 714.491.0192
800.633.9876 714.491.1500 FAX 714.491.1517
The Netherlands
Streszczenie treści zawartej na stronie nr. 2
Precautions Safety Instructions • English Warning FCC Class A Notice Power sources This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is Note: This equipment has been tested and found to comply with the limits for a in the litera
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About this Manual ................................................................ 1-2 About the RGB 400 Series Interfaces .......................... 1-2 Features ...................................................................................... 1-2 RGB 400 Series features ......................................................... 1-2 Additional RGB 404 features ..........................
Streszczenie treści zawartej na stronie nr. 4
Table of Contents, cont’d Appendix C Dimensions ........................................................ C-1 RGB 400 Series RGB 404 Panel Dimensions ............................................... C-2 RGB 406 Panel Dimensions ............................................... C-5 RGB 408 Panel Dimensions ............................................... C-6 RGB 408 Panel Dimension Details ................................. C-7 Appendix D Accessories and Part Numbers .......... D-1 Interfaces and I
Streszczenie treści zawartej na stronie nr. 5
Introduction, cont’d Introduction About this Manual RGB 400 Series This manual contains information about the RGB 400 Series interfaces and on how to operate and configure them. About The RGB 400 Series Interfaces The RGB 400 Series are 300 MHz (-3dB) bandwidth, analog computer-video interfaces that can be mounted in walls or furniture. The RGB 406 is two-gang wall plate size, the RGB 404 is three-gang size, and the RGB 408 is four-gang size. All are available with black, white, or gray panels
Streszczenie treści zawartej na stronie nr. 6
Installation and Operation, cont’d Installation and Operation Installation Overview Installation and Operation Instructions To install and set up an RGB 400 Series interface, follow Determining installation location these basic steps: Take cabling and power availability and the location of wall 1 Determine the installation location. studs into consideration when selecting an installation site. You may need to install the cables in the wall, furniture or 2 Prepare the site for installation. Use
Streszczenie treści zawartej na stronie nr. 7
Installation and Operation, cont’d Preparing the installation site and installing the wall box Actual-size rough-in templates for each model are provided Wall Stud in Appendix B. If needed, make a 100% size photocopy of the appropriate template to use for installation. Compare Wall Box the photocopy with the faceplate and wall box to make sure the photocopy size is the same as the equipment. Use the template as a guide to mark and cut the hole in the wall or furniture through which the interfa
Streszczenie treści zawartej na stronie nr. 8
Installation and Operation, cont’d Front and rear panel (circuit board) features 18 17 19 16 RGB 404 front and rear features Yellow Red 17 18 Black Green J9 SW1 S-VIDEO J8 VIDEO J10 HIGH Z INPUT A L R 75 Ohm J13 U D I AUTO POWER O 1 = +5V 20 mA max. .8V .9V 32 1 2 = –5V 20 mA max. H G J9 3 = Ground J13 B R RGB 406/ J9 .7V V .8V PC 1. ON = Remove RGB 408 SW1 .7V CS serration pulses. Captive .7V NETWORK .9V J8 2. ON = Digital Screw J10 display sync. Connector J10 J8 33-398-01 B 08 9
Streszczenie treści zawartej na stronie nr. 9
Installation and Operation, cont’d RGB 406 front and rear features 14 SW1 DIP switches — 9 1. On = Removes serration pulses. 2. On = Enables Digital Display Sync Processing (DDSP). J9 10 J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board. INPUT HIGH Z SW1 J8 J10 J9 green gain/peaking jumper 11 75 Ohm 12 J8 red gain/peaking jumper AUTO POWER AUDIO J13 Circuit board — Only key components are shown here. 13 H. SHIFT Twisted-pair wires — Splice these wi
Streszczenie treści zawartej na stronie nr. 10
Installation and Operation, cont’d 15 RGB 408 front and rear features J9 HIGH Z INPUT SW1 J8 J10 75 Ohm AUTO POWER AUDIO J13 H. SHIFT 1 = +5V 20 mA max. .8V .9V 32 1 2 = –5V 20 mA max. H G J9 3 = Ground J13 B R RGB 406/ J9 .7V V 1. ON = Remove RGB 408 .8V SW1 .7V CS Extron RGB 408 serration pulses. .7V Captive .9V J10 J8 2. ON = Digital Screw J8 display sync. Connector J10 33-398-01 B 08 99 FRONT REAR 78 91011 12 13 14 6 123 4 5 6 1 Auto power LED — If this LED is on, power and vi
Streszczenie treści zawartej na stronie nr. 11
Installation and Operation, cont’d Each red (J8), green (J9) and blue (J10) jumper can be set to Setting DIP switches and jumpers one of three positions to provide unity gain (0.7 volts p-p), DIP switches and jumpers must be set and tested before the 0.8 volts p-p, or 0.9 volts p-p output. Select the setting that interface is secured into the wall box, wall or furniture. yields the best image display. Use the diagram on the product label (shown below) as a guide to setting the DIP switches out
Streszczenie treści zawartej na stronie nr. 12
INPUT HIGH Z 75 Ohm AUTO POWER AUDIO H HIF . S T RGB 408 Installation and Operation, cont’d Cabling RCA connectors Adapter Plate For composite video, solder the center conductor of a coaxial cable to the central solder cup of the RCA connector. Solder the cable’s shield to the grounded grounding tab. See the leftmost and center illustrations below. #4-40 Nut w/Captive Center Central Solder Washer Conductor Cup Shield Grounding Tab RGB 408 (Up to 4 Plates) Coaxial Cable RCA Connector Twisted Pair
Streszczenie treści zawartej na stronie nr. 13
Installation and Operation, cont’d If shielded twisted-pair wires are used for audio output for signal. For example, the input signals from the left side of the RGB 404, RGB 406 or RGB 408, the shields should be channel one (CH1L) are output as CH1L+ and CH1L-. The connected to either pin 3 (RGB 406/408) or pins 3 and 8 following illustration shows the audio inputs and outputs (RGB 404) of the audio output captive screw connector. and how to wire the audio connectors. Twist the wires from the
Streszczenie treści zawartej na stronie nr. 14
Installation and Operation, cont’d output captive screw connector. See “Connecting Using installation cable shields” earlier in this chapter for details. Extron’s Install Plenum bulk cable (shown here) is ideal for mountable interfaces such as the RGB 400 Series models. Connecting audio cables — RGB 406, RGB 408 Six Mini, High-resolution Each RGB 406 or RGB 408 accepts an unbalanced audio Double Shielded Coaxial Conductors Foil and Copper Strand input from a front panel 3.5 mm PC-type stereo co
Streszczenie treści zawartej na stronie nr. 15
Installation and Operation, cont’d 3. Check the cabling and the audio connector wiring, the situation, either the pass-through connector or any and make adjustments as needed. cable that was part of the installation but not used for this test may be the source of the problem. If this test 4. Verify that the High Z/75 Ohm video input does not produce an image or sound, the problem termination toggle switch on the front panel has been may lie with an input device or an output device. set correctl
Streszczenie treści zawartej na stronie nr. 16
Installation and Operation, cont’d 4. For all models, carefully place the interface through Application diagrams the opening in the wall or furniture and into the wall Below are examples of typical system installations that box (if one is used). Take care not to damage the incorporate RGB 400 series interfaces. Many other cables. configurations are possible. Extron offers a variety of 5. Mount the interface faceplate to the wall box with the laptop and monitor breakout cables for easy connect
Streszczenie treści zawartej na stronie nr. 17
Installation and Operation, cont’d RGB 400 Series Appendix A A Specifications Specifications 2-24 RGB 400 Series Installation and Operation
Streszczenie treści zawartej na stronie nr. 18
Specifications, cont’d Specifications These specifications apply to all models unless otherwise noted. Audio input — RGB 404 Number/type ............................... 2 stereo, unbalanced; 1.0Vrms (+4dBu), Video input 20 Hz to 20 kHz Number/type ............................... 1 analog RGBHV, RGBS, RGsB Connectors .................................... Ch. 1 ........... 2 RCA female jacks Connectors .................................... 1 9-pin male D connector for Ch. 2 ........... 3.5 mm ste
Streszczenie treści zawartej na stronie nr. 19
Specifications, cont’d Impedance .................................... 50 ohms, unbalanced, 100 ohms balanced Approvals ..................................... UL, CE, FCC Class A Gain error ...................................... ±0.1dB channel to channel MTBF ............................................. 30,000 hours Drive (600 ohm) ........................... +14dBu, balanced at stated %THD+N Warranty ....................................... 2 years parts and labor General Specifications are subje
Streszczenie treści zawartej na stronie nr. 20
Specifications, cont’d RGB 400 Series Appendix B B Templates RGB 406 Cut-out Template RGB 404 Cut-out Template RGB 408 Cut-out Template A-6 RGB 400 Series Specifications