Streszczenie treści zawartej na stronie nr. 1
FD600.1
FD1200.1
Streszczenie treści zawartej na stronie nr. 2
Supplying Enough Power Congratulations! Thank you for purchasing an ARC Audio Hi-Performance Amplifier. The Laws of Nature Your amplifier Does NOT make power. It converts power, or current, from your cars electrical system ARC Audio amplifiers are conservatively rated and produce more power per channel and turns it into a high power musical energy. If the amp can't get all the power it needs it will not than others in there class. Manufactured to the highest standards of quality and produce
Streszczenie treści zawartej na stronie nr. 3
Input Section Bass Boost Because of the wide range of head unit output configurations all ARC This amp has a fully adjustable bass boost. Both the frequency and the Audio amplifiers have an adjustable input sensitivity or “Gain” . The gain level of the boost are adjustable. Start with a small increase in the level is not a volume or a power limiting control like a throttle. It makes the control. Then “sweep” the frequency up and down. Listen carefully for an amp more sensitive to input fro
Streszczenie treści zawartej na stronie nr. 4
Bridging Bridging Cont. Bridging is a way to combine the power of 2 channels into 1. When For bridging to work both amplifiers must be playing exactly the same you wire the amp bridged you have a higher voltage differential signal at exactly the same output level. To make this easier we have between + and -. That means MORE POWER. added a “Slave In” and “Slave Out” to this amp. When you use the Slave In all the gain and crossovers are bypassed. This eliminates all the compli- If you have 2
Streszczenie treści zawartej na stronie nr. 5
Installation Instructions 9. Connect the speaker wire to the amp and speakers (make sure 1. Disconnect the negative cable from the car battery. Tape up the end the amp is off first). Make sure the polarity (+ and-) is correct. so it is isolated form the battery. 10. Connect the RCA’s to the amp. 2. Run the power wire (4 AWG min.) from the battery to the amplifier. 11. Double check the amplifier controls at this time. Make sure Plan this part of the installation carefully. This cable
Streszczenie treści zawartej na stronie nr. 6
2 OHM OPERATION 1 OHM OPERATION SET PHASE TO SET LOAD TO SET INUT TO SET PHASE TO SET LOAD TO SET INUT TO NORMAL> - - 2 0HMS 1 0HMS + + _ 10D2 = 2 _ 10D4 = 2 _ 10D2 = 1 _ + + 12D2 = 2 10D2 = 1 12D4 = 2 + 12D2 = 1 + 12D2 = 1 _ 10D4 = 2 _ + _ 12D4 = 2 10D2 = 1.33 10D4 = 1 + + 12D4 = 1 12D2 = 1.33 10 11
Streszczenie treści zawartej na stronie nr. 7
4 OHMS BRIDGED In this configuration you can “Bridge” 2 amplifiers into 1 channel. To bridge 2 amps you must set amp 1 to “Normal” and amp 2 to “Slave” . All adjustments will then be made to amp 1. Amp 2 will need no further adjustments SET PHASE TO SET LOAD TO SET INUT TO SET PHASE TO SET LOAD TO SET INUT TO NORMAL> OUT> TWO>
Streszczenie treści zawartej na stronie nr. 8
2 OHMS BRIDGED In this configuration you can “Bridge” 2 amplifiers into 1 channel. To bridge 2 amps you must set amp 1 to “Normal” and amp 2 to “Slave” . All adjustments will then be made to amp 1. Amp 2 will need no further adjustments SET PHASE TO SET LOAD TO SET INUT TO SET PHASE TO SET LOAD TO SET INUT TO OUT>
Streszczenie treści zawartej na stronie nr. 9
POWER AND INPUT CONNECTIONS POWER AND INPUT CONNECTIONS DUAL BATTERY or BATTERY AND CAPACITOR SINGLE BATTERY FUSE FUSE REMOTE REMOTE Battery or Capacitor FUSE Battery This is a stock ground wire on the This is a stock ground wire on the battery between the battery and battery between the battery and Battery the body. It should be Upgraded to the body. It should be Upgraded to 4 AWG from the factory 8 or 10 4 AWG from the factory 8 or 10 AWG. AWG. 16 17 4 AWG. 18” MAX. 4 AWG. 18” MAX. 4 AWG
Streszczenie treści zawartej na stronie nr. 10
Specifications FD600.1 FD1200.1 1 Channels @ 4Ohms 336 Watts 510 Watts 1 Channels @ 2Ohms 620 Watts 1010 Watts 1 Channels @ 1Ohm 600 Watts 1100 Watts 20 Hz > 250Hz 20 Hz > 250Hz Frequency Response Crossover Range 30Hz - 250Hz 55Hz - 250Hz Bass Boost 0 - 18dB @ 30Hz - 80Hz 0 - 18dB @ 30Hz - 80Hz >75 dB >89 dB S/N Ratio (A wtg) ref 1Watt 4Ohm >NA Seperation @ 1kHz >NA >3334 > 2100 Damping (25W 4x4Ohm 100Hz) Low Level Input Sensitivity .25V - 2.5V .25V - 2.5V Max Peak Current 2Ohm S
