Streszczenie treści zawartej na stronie nr. 1
INTEGRATED CIRCUITS
DATA SHEET
TDA6111Q
Video output amplifier
1995 Feb 07
Preliminary specification
Supersedes data of February 1992
File under Integrated Circuits, IC02
Philips Semiconductors
Streszczenie treści zawartej na stronie nr. 2
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q FEATURES GENERAL DESCRIPTION • High bandwidth and high slew rate The TDA6111Q is a video output amplifier with 16 MHz bandwidth. The device is contained in a single in-line 9-pin • Black-current measurement output for Automatic medium power (DBS9MPF) package, using high-voltage Black-current Stabilization (ABS) DMOS technology, intended to drive the cathode of a • Two cathode outputs; one for DC currents, and one for
Streszczenie treści zawartej na stronie nr. 3
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q BLOCK DIAGRAM supply voltage feedback input HIGH output handbook, full pagewidth 6 9 7 V MIRROR MIRROR FOLLOWERS cathode 7 transient V bias output C par 8 cathode inverting 3 DC output input DIFFERENTIAL 1 STAGE TDA6111Q non-inverting black current 5 input measurement output CURRENT MIRROR MIRROR SOURCE 42 MGA058 ground supply voltage (substrate) input LOW Fig.1 Block diagram. 1995 Feb 07 3
Streszczenie treści zawartej na stronie nr. 4
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q PINNING SYMBOL PIN DESCRIPTION V 1 non-inverting voltage input ip V 2 supply voltage LOW DDL andbook, halfpage V 1 ip V 3 inverting voltage input in V 2 DDL GND 4 ground, substrate V I 5 black current measurement 3 in om output GND 4 V 6 supply voltage HIGH DDH I 5 TDA6111Q om V 7 cathode transient voltage output cn V 6 DDH V 8 cathode DC voltage output oc V 7 cn V 9 feedback voltage output fb V 8 oc V 9 fb MGA057 Fig
Streszczenie treści zawartej na stronie nr. 5
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). Voltages measured with respect to GND (pin 4); currents as specified in Fig.1; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT V high level supply voltage 0 250 V DDH V low level supply voltage 0 14 V DDL V input voltage 0 V V I DDL V differential mode input voltage -6+6 V Idm V measurement output voltage 0 V om DDL V
Streszczenie treści zawartej na stronie nr. 6
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q CHARACTERISTICS Operating range: T = - 20 to 65 °C; V = 180 to 210 V; V = 10.8 to 13.2 V; V = 2.6 to 5 V; amb DDH DDL ip V =1.4VtoV . om DDL Test conditions (unless otherwise specified): T =25 °C; V = 200 V; V = 12 V; V =5V; V =6V; C =10pF amb DDH DDL ip om L (C consists of parasitic and cathode capacitance); R = 10 K/W; measured in test circuit Fig.3. L th-heatsink SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT I qui
Streszczenie treści zawartej na stronie nr. 7
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT O cathode output voltage overshoot V = 100 V (p-p); - 9 - % v ocAC V = 100 V square ocDC wave; f < 1 MHz; t =t =22ns; r f see Figs 4 and 5; note 1 SVRRH high supply voltage rejection ratio f < 50 kHz; note 2 - 85 - dB SVRRL low supply voltage rejection ratio f < 50 kHz; note 2 - 70 - dB Notes 1. If the difference between V and V is less than 7 V, overshoot cannot be spec
Streszczenie treści zawartej na stronie nr. 8
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q 12 V 200 V handbook, full pagewidth C C1 C3 par 22 nF 3.9 pF C5 C6 22 nF 100 nF C4 V i 10 μF R10 68.1 kΩ R9 C2 C7 10 μF 820 Ω 22 μF 3 926 R1 1.4 mA TDA6111Q 7 50 Ω C n 1 458 560 pF A C8 R3 6.8 pF 20 MΩ 5 V C7 probe V om 3.2 pF 6 V C9 R2 C10 100 nF 136 pF 1 MΩ MGA059 - 1 C = 150 fF. par 1 Fig.3 Test circuit with feedback factor ⁄ . 83 1995 Feb 07 8
Streszczenie treści zawartej na stronie nr. 9
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q x V i 0 t x t s overshoot (in %) 151 150 140 V 149 oc 100 60 50 t t r MGA974 t pd Fig.4 Output voltage (pin 8) rising edge as a function of the AC input signal. 1995 Feb 07 9
Streszczenie treści zawartej na stronie nr. 10
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q x V i 0 t x t s 150 140 V oc 100 overshoot (in %) 51 60 50 49 t t f MGA975 t pd Fig.5 Output voltage (pins 8) falling edge as a function of the AC input signal. 1995 Feb 07 10
Streszczenie treści zawartej na stronie nr. 11
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q TEST AND APPLICATION INFORMATION The dynamic dissipation equals: P =V × (C +C +C ) × f × V ×δ Dissipation dyn DDH L fb int i o(p-p) C = load capacitance. L Regarding dissipation, distinction must first be made between static dissipation (independent of frequency) and C = feedback capacitance (≈ 150 fF). fb dynamic dissipation (proportional to frequency). C = internal load capacitance (≈ 4 pF). int The static dissipati
Streszczenie treści zawartej na stronie nr. 12
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q PACKAGE OUTLINE DBS9MPF: plastic DIL-bent-SIL medium power package with fin; 9 leads SOT111-1 D D 1 q A 2 P P 1 Q A 3 q 2 q 1 A A 4 E pin 1 index c L 19 e e b Z 2 b w M 2 θ b 1 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) A (1) 2 (1) (1) Z UNIT A A Abc bb D D E eL e PP qqq w Q θ 3 4 12 12 1 1 2 max. max. o 18.5 8.7 15.5 1.40 0.67 1.40 0.48 21.8 21.4 6.48 3.9 2.75 3.4 1.75 15.1 65 4.4 5.9 mm 3.7 2.54 2.5
Streszczenie treści zawartej na stronie nr. 13
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q SOLDERING REPAIRING SOLDERED JOINTS Apply the soldering iron below the seating plane (or not Plastic single in-line packages more than 2 mm above it). If its temperature is below BY DIP OR WAVE 300 °C, it must not be in contact for more than 10 s; if between 300 and 400 °C, for not more than 5 s. The maximum permissible temperature of the solder is 260 °C; this temperature must not be in contact with the joint for mor
Streszczenie treści zawartej na stronie nr. 14
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q NOTES 1995 Feb 07 14
Streszczenie treści zawartej na stronie nr. 15
Philips Semiconductors Preliminary specification Video output amplifier TDA6111Q NOTES 1995 Feb 07 15
Streszczenie treści zawartej na stronie nr. 16
Philips Semiconductors – a worldwide company Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428) Pakistan: Philips Electrical Industries of Pakistan Ltd., BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367 Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton, KARACHI 75600, Tel. (021)587 4641-49, Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Fax. (021)577035/5874546. Tel. (02)805 4455, Fax. (02)805 4466 Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc, Austria: Triester Str. 64, A-110
