Instrukcja obsługi Soundstream Technologies SPL40

Streszczenie treści zawartej na stronie nr. 1

2 Ohm Nominal
Component
Speaker System
OWNER’S MANUAL
1
page 1
Friday, September 10, 1999 21:04 40.pub

Streszczenie treści zawartej na stronie nr. 2

SPL 40 Component Speaker System Congratulations on your purchase of the Soundstream SPL 40 Component Speaker System. When used with a high quality 2 ohm rated power amplifier, the SPL 40 will provide exceptional performance. As with all high quality c ar audio components, professional installation is recommended. Your dealer’s knowledge and experience can ensure a problem - free , cosmetically integrated installation. If you plan on installing the SPL 40 speaker system yourself, ple

Streszczenie treści zawartej na stronie nr. 3

FEATURES SPL 4 Midrange / Woofer The SPL 4 is an excellent performer with a combination of high sensitivity, solid bass and smooth response t hroughout the audible •Lightweight Cone designed for good rigidity and high sensitivity •2 Ohm Voice Coil SPL 1 Aluminum Dome Neodymium Tweeter The SPL 1 tweeter is a high performance 1” Neodymium tweeter •Black Aluminum 1" dome for improved power handling and linear response • Ferrofluid-immersed Voice Coil •Vented Aluminum Voice Coil Fo

Streszczenie treści zawartej na stronie nr. 4

The first step in a successful installation is thorough LOCATION planning. Choose the location for your speaker AND components carefully. F ollow these suggestions to MOUNTING • Select a location where each tweeter and midrange/woofer can be mounted close to each her. A good rule of thumb is a maximum of one foot from cone to tweeter. • Choose a location that offers the least • • Always check behind the chosen mounting locations to make sure that there are no obstructions (

Streszczenie treści zawartej na stronie nr. 5

1 / ” 6-32 machine 4 Turn Clockwise to Lock screw Flush mount cup Mounting surface Spring FIGURE 1 clip FIGURE 2 Surface Mounting: Drill one 5/16" diameter hole for the tweeter lead wires and two pilot - clockwise until locked. See figure 4. Turn Counter-Clockwise to Lock FIGURE 3 FIGURE 4 5 page 5 Friday, September 10, 1999 21:04 40.pub the plate and rotate counter ing holes on the back of the tweeter onto the tabs on Engage the lock 4) Pass the lead wires through th

Streszczenie treści zawartej na stronie nr. 6

The SPL 4 Midrange/Woofer can be mounted on INSTALLING the front or rear of a panel; gaskets are provided THE SPL 4 for both options. The bolt hole configuration will fit a variety of American, European and Asian OEM MIDRANGE/ patterns making it ideal for direct placement. Best WOOFER perfor mance is achieved when the speaker is s ecurely mounted to a door panel or rear deck. There should be no gaps between the speaker and the mounting surface, as this wil l impair its low freque

Streszczenie treści zawartej na stronie nr. 7

Tweeter Attenuation TWEETER The SPL 40 system has been designed to provide LEVEL optimum sound in a variety of installation locations. The provid ed crossover allows for 2 positions of tweeter CONTROL level control, 0dB and - 3dB. A switch under the plastic crossover cover sets one of the two positions. The factory setting is 0 dB. Tweeter Level Control Switch FIGURE 5 Wiring Diagram WIRING Figure 6 shows a diagram illustrating the wiring of the SPL 40 Component Speaker System.

Streszczenie treści zawartej na stronie nr. 8

SPECIFICATIONS SPL 40 System Specifications - 2 Ω SPL 4 Midrange/Woofer - 2 Ω - SPL 1 Metal Dome Tweeter - 4 Ω - (Rev A, 1/3/97) 8 page 8 Friday, September 10, 1999 21:04 40.pub fax 916.351.0414 tel 916.351.1288 120 Blue Ravine Road  Folsom  California 95630 USA 3/4" Mounting Depth (flush mount) 2 1/16” Out Diameter Mounting Cut 1” Nominal Tweeter Diameter Nominal Impedance 94 dB SPL at 1 meter (2.83 Volt