Streszczenie treści zawartej na stronie nr. 1
ADDENDUM
Addendum No. C3409M
Date December 22, 2005
Manuals Affected C2462M-B, C2403M-C, C2410M-H,
C2491M-B, C2496M
Manual Update Switch Settings for Varifocal Lens
Manual Update The high resolution camera with vari-
focal lens and auto iris is configured at
the factory for automatic exposure.
SWITCH SETTINGS FOR VARIFOCAL LENS
The high resolution camera with varifocal lens and auto iris is configured at the factory for
automatic exposure.
1 AWB Automatic white balance
FACTORY SETTINGS
2 GA
Streszczenie treści zawartej na stronie nr. 2
INST ALLA TION ® 110 Series Camclosure Integrated Camera System ® C2403M-C (10/05)
Streszczenie treści zawartej na stronie nr. 3
Contents Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . .
Streszczenie treści zawartej na stronie nr. 4
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Use only with the cart, stand, tripod, br
Streszczenie treści zawartej na stronie nr. 5
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class A (black-white, EIA and CCIR cameras - except auto iris models) RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class
Streszczenie treści zawartej na stronie nr. 6
Description ® The ICS110 Series Camclosure integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple mounting options. The ICS110 Series Camclosure can be installed directly to a ceiling, wall, 4S electrical box (using the optional ICS110-AP adapter plate), or a st
Streszczenie treści zawartej na stronie nr. 7
Installation MOUNTING DIRECTLY TO SURFACE WIRING THROUGH BASE Follow the proceeding steps when feeding wire/cables through the base of the cover and back box: 1. Using the cover as a template, mark one of the large hole positions onto the COVER mounting surface. 2. Cut out the hole in the mounting surface for power and video wiring. 3. Pull video and power wires through the hole in the cover. 4. Attach the cover to the mounting surface BACK BOX (hardware not supplied). Use stainle
Streszczenie treści zawartej na stronie nr. 8
WIRING THROUGH SIDE CONDUIT Follow the proceeding steps when feeding wire/cables through the side conduit opening of the unit: 1. Attach the cover to the mounting surface (hardware not supplied). Use stainless steel hardware when installing the system outdoors. 2. Remove the conduit plug from the side of the back box. 3. Use a blunt tool to pull the wires and plug, located on the base of the back box into the back box. Insert the black plug (supplied) into the hole in the base of the
Streszczenie treści zawartej na stronie nr. 9
5 5 0 404 Install Camera WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting the camera. This applies to all models. 1. Some indoor installations do not require a heater. If the installation does not require a heater, remove the heater board from the HEATER BOARD camera assembly. To remove the heater press on an end of the board. 2. 12 VDC operation only: The camera is set for VIDEO 24 VAC operation at the factory. For 12 VDC CONNECTOR opera
Streszczenie treści zawartej na stronie nr. 10
5. Always make sure the tab on the camera bracket is pointing out of the enclosure (away from the ceiling or wall). Gently squeeze the bracket, place it against the groove inside back box, and gently release. Proper camera orientation: CAMERA BRACKET TAB ALWAYS POINTS TOP OF OUT OF THE CAMERA ENCLOSURE CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE Wall Mounting – The camera Ceiling Mounting – The camera bracket bracket tab points out of the tab points out of the enclosure and t
Streszczenie treści zawartej na stronie nr. 11
5 5 0 404 Install Dome and Trim Ring 1. Domes with Liners (only) – 2. Align the screw holes in the trim ring with ADJUSTMENT those in the Camclosure base. GROOVE Position the viewing window over the lens of DOME LINER the camera. a. Loosen the three Phillip screws located LOOSEN SCREWS in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves. Move the dome into position. c. Tighten the three Phillip screws to lock the liner in place. 3. Tighten
Streszczenie treści zawartej na stronie nr. 12
5 5 0 404 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. VARIFOCAL LENS FIXED LENS IRIS LEVEL ADJUSTMENT AUTO IRIS LEVEL ADJUSTMENT FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting the camera. To adjust the focus, it may be necessary to remove the heater board in
Streszczenie treści zawartej na stronie nr. 13
SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details. Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots. ALC/ELC switch: Alway
Streszczenie treści zawartej na stronie nr. 14
SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for optimal performance in lighting conditions where auto iris is required. It is also configured with the shutter speed set at 1/60 (NTSC) or 1/50 (PAL) and manual gain set at 6 dB. 1 AWB Automatic white balance FACTORY SETTINGS 2 GAM Gamma function 1 2 3 4 5 6 7 8 3 AGC Automatic gain control UP 4 ESC Electronic shutter control DOWN OFF 5 BLC Back
Streszczenie treści zawartej na stronie nr. 15
Specifications General Operating Temperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fitting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/Tilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camera mounting bracket and polycarbonate dome Finish Gray polyester powder coat Environment Low temperature, indoor/outdoor Unit Weight: 2.2 lb (1.0 kg) Electrical Input Voltage 12 VDC or 24 VAC, ±10% Power Cons
Streszczenie treści zawartej na stronie nr. 16
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2,
Streszczenie treści zawartej na stronie nr. 17
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |
