Streszczenie treści zawartej na stronie nr. 1
AutoDome Junior
VJR-A3-IC
en Installation Manual
Streszczenie treści zawartej na stronie nr. 2
Streszczenie treści zawartej na stronie nr. 3
AutoDome Junior Table of Contents | en 3 Table of Contents 1 Installing a Recessed Mount 4 1.1 Description 4 1.1.1 Additional Requirements 4 1.1.2 Preparing the Ceiling for Installation 5 1.1.3 Installing the Camera to the Mounting Plate 8 Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
Streszczenie treści zawartej na stronie nr. 4
4 en | Installing a Recessed Mount AutoDome Junior 1 Installing a Recessed Mount 1.1 Description This chapter details how to recess mount the AutoDome Junior. NOTICE! The image sensors in modern CCD cameras are highly sensitive and require special care for proper performance and extended lifetime. Follow the guidelines for optimum results with your camera: – Do not expose to direct sunlight or bright spotlights in operating and nonoperating conditions. – Avoid bright lights in the field
Streszczenie treści zawartej na stronie nr. 5
AutoDome Junior Installing a Recessed Mount | en 5 1.1.2 Preparing the Ceiling for Installation To mount to a recess mount, do the following: 1. Determine a secure location for the recessed mount (supplied separately). 104.9 (4.13) 71.6 (2.82) mm (in.) 229.0 (9.02) Figure 1.1 Recess Mount Dimensions 2. Drill or cut a 200 mm hole with a tolerance of 2.2 mm ( 7.9 in. ± 1/8). 3. Optional: if installing the AutoDome Junior HD to a suspended ceiling tile or any other surface where additional supp
Streszczenie treści zawartej na stronie nr. 6
6 en | Installing a Recessed Mount AutoDome Junior 4. Align holes of mounting plate (supplied with dome) with mounting bracket and attach with screws. Ensure that both the crescent shape of the mounting plate and the crescent shape of the mounting bracket are aligned. Figure 1.2 Attach Mounting Plate to Mounting Bracket 1 Mounting Bracket 2 Mounting Plate 3 Clamping Plate 4 Crescent Shape 5 Clamp Drive Screw 5. Loosen the two clamp drive screws (item 5, above) so that the clamping plates mov
Streszczenie treści zawartej na stronie nr. 7
AutoDome Junior Installing a Recessed Mount | en 7 Figure 1.3 Attach Recess Mount to Ceiling 7. Tighten both clamps using the clamp drive screws (installed on the assembly) and a #2 Phillips screwdriver. NOTICE! Over-torquing the ceiling clamps can damage the clamp or ceiling. Only tighten the clamp until it contacts the ceiling and you start to feel some resistance. If using a power screwdriver, set the torque level to the lowest setting. NOTICE! If you need to install the the VJR-A3-SP S
Streszczenie treści zawartej na stronie nr. 8
8 en | Installing a Recessed Mount AutoDome Junior 1.1.3 Installing the Camera to the Mounting Plate To install the base to a surface or suspended ceiling using the supplied mounting plate, do the following: 1. Loosen the single safety locking screw on the base of the unit using the user-supplied T-10 Torx wrench. Figure 1.4 Unlock Safety Locking Screw CAUTION! All wires for installation applications must be routed through a grounded conduit. 2. Remove the screw from the Earth ground ( )on t
Streszczenie treści zawartej na stronie nr. 9
AutoDome Junior Installing a Recessed Mount | en 9 7. Plug the matching connectors from the camera into the mating connectors from the ceiling. Figure 1.5 Match Connectors 1 Locking Screw 2 Crescent Shape 3 Mounting Plate 4 Vertical Tab Bosch Security Systems, Inc. Installation Manual F.01U.168.034 | 3.0 | 2010.12
Streszczenie treści zawartej na stronie nr. 10
10 en | Installing a Recessed Mount AutoDome Junior 8. Attach the camera to the mounting plate by inserting the vertical tab on the plate (item 1, below) into the recessed slot on the top of the camera dome (Item 3) to the right of the safety locking screw (item 2). Note: Do not loosen the three brass buttons (item 4). These brass buttons engage the slotted tabs (item 5) on the mounting plate. Figure 1.6 Tab/Slot Alignment Detail 1 Vertical Tab (on mounting plate) 2 Locking Screw 3 Recesse
Streszczenie treści zawartej na stronie nr. 11
AutoDome Junior Installing a Recessed Mount | en 11 9. Rotate the camera approximately 15 degrees in the clockwise direction. Then, lock firmly into place, as shown in the next illustration. Figure 1.7 Attach Dome to Mounting Plate 1 Recess Mounting Bracket 2 Mounting Plate 3 Mounting Bracket Tether Point 10. Ensure unit is centered. NOTICE! The recessed mounting bracket is provided with an additional safety tether point. To prevent injury, attach a safety wire from a secure anchor point
Streszczenie treści zawartej na stronie nr. 12
12 en | Installing a Recessed Mount AutoDome Junior 11. Align trim ring so the four alignment posts (item 1, below) align with the recesses in the camera housing (item 2) and so the two safety screws align with the off center holes (item 3) on the locking clamps. Note: The two (2) sets of raised stand-off tabs (item 4) on each side of the trim ring align with the locking clamps. Figure 1.8 Align Trim Ring 1 Alignment Tabs (four) 2 Align tabs to the recessed areas on the housing 3 Align safe
Streszczenie treści zawartej na stronie nr. 13
Streszczenie treści zawartej na stronie nr. 14
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc., 2011
