Streszczenie treści zawartej na stronie nr. 1
OPERATION MANUAL
MODELS
CS403016
CS403020
CS403026
CS403030
PAVEMENT SAW
(DEUTZ F2L2011 DIESEL ENGINE)
Revision #0 (02/29/08)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 37747
Streszczenie treści zawartej na stronie nr. 2
Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber. Your risk from these exposures varies, dependingonhowoftenyoudothistype of
Streszczenie treści zawartej na stronie nr. 3
WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drillingofmasonry,concrete,metaland Grinding/cutting/drillingofmasonry,concrete,metaland othermaterialswithsilicaintheircompositionmaygive other materials can generate dust, mists and fumes off dust or mists containing crystalline silica. Silica is a containing chemicals known to cause serious or fatal basiccomponentofsand,quartz,brickclay,graniteand injury or illness, such as respiratory disease, cancer, numerous other miner
Streszczenie treści zawartej na stronie nr. 4
STOW CS4030 SAW — TABLE OF CONTENTS Table of Contents .................................................... 4 Dimensions ............................................................. 5 Specifications .......................................................... 6 Engine Specifications .............................................. 7 Training Checklist .................................................... 8 Daily Pre-Operation Checklist ................................. 9 Safety Message Alert Symbols
Streszczenie treści zawartej na stronie nr. 5
STOW CS4030 SAW — DIMENSIONS E C D A B Figure 1. Chassis & Dimensions - Sideview TABLE 1. CHASSIS & DIMENSIONS REFERENCE DIMENSIONS DESCRIPTION LETTER in. (mm) A Max Height (Raised/Front Pointer up) 71 in. (1803 mm) B Max Handle Bar Height 47 in. (119 mm) C Max Length (Handle Bars Installed & Front Pointer fully raised) 88 in. (2235 mm) D Length (Handle Bars not Installed & Front Pointer fully raised) 63 in. (1600 mm) E Max Length (Handle Bars Installed & Front Pointer lowered) 116 in. (2946 mm)
Streszczenie treści zawartej na stronie nr. 6
STOW CS4030 SAW — SPECIFICATIONS H L G K F I J Figure 2. Chassis & Dimensions - Bottomview TABLE 2. BLADE AND SHAFT SPECIFICATIONS Oil bath design, fully enclosed cast iron housing Blade Shaft Assembly Oil lubricated, no lubrication requirements Blade Shaft Bearings 2-3/8 in. (60mm) Blade Shaft Diameter 1 in. (25.4 mm) Arbor Diameter Quick disconnect system, inner flanges mounted to shaft Blade Flanges 4-1/2 in.a5 nd in. (114mma7 nd 12 mm) Blade Flange Sizes Drive Belt (1) 6G 3VX-500 multi-groov
Streszczenie treści zawartej na stronie nr. 7
STOW CS4030 SAW — ENGINE SPECIFICATIONS TABLE 3. ENGINE / MOTOR SPECIFICATIONS Engine Manufacture Deutz F2L 2011 Model Max RPM 3000 Horsepower / Max kW 31.3 hp / 23.0 kW Peak Torque 66.3 lb./ft. (90 Nm) Fuel Diesel Fuel Capacity 6.0 gallons / 22.7L Air Filter Dual element radial seal with integral turbo pre-cleaner Oil Capacity 7 Qts. (6.6L) Engine Coolant Oil to Air TABLE 4. TRANSMISSION SYSTEM SPECIFICATIONS Transmission Pump Hydro-gear hydrostatic transmission pump Wheel Motors Hydro-gear hyd
Streszczenie treści zawartej na stronie nr. 8
TRAINING CHECKLIST TRAINING CHECKLIST This checklist lists the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist when training a new operator or use as a review for more experienced operators. TRAINING CHECKLIST NO. DESCRIPTION OK? DATE 1 Read Operator’s Manual completely. 2 Machine layout, location of components, checking of engine and hydraulic oil levels. 3 Fuel system, refueling procedure. 4 Operation of spray and
Streszczenie treści zawartej na stronie nr. 9
DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST 1 Hardware and damage check. 2 Engine oil level. 3 Hydraulic oil level. 4 Condition of blade. 5 Safety Stop Switch operation. 6 Braking control operation. COMMENTS: STOW CS4030 SAW � OPERATION MANUAL — REV. #0 (12/13/07) — PAGE 9 /02) — PAGE 9
Streszczenie treści zawartej na stronie nr. 10
SAFETY MESSAGE ALERT SYMBOLS HAZARD SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and Lethal Exhaust Gases comply with the Safety Messages and Operating Instructions could result in injury to yourself and others. Engine exhaust gases contain harmful toxins and will displace oxygen when running in an This Operation Manual has been enclosed or confined area. NEVER operate develope
Streszczenie treści zawartej na stronie nr. 11
SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard Accidental starts can cause severe injury or death. ALWAYS place the ON/OFF switch in the OFF position. Disconnect negative battery cable from battery before servicing. ALWAYS wear approved respiratory protection. Sight and Hearing hazard Over Speed Conditions ALWAYS wear approved eye and hearing protection. NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or
Streszczenie treści zawartej na stronie nr. 12
STOW CS4030 SAW — RULES FOR SAFE OPERATION ■ NEVER operate this equipment when not feeling well due to RULES FOR SAFE OPERATION fatigue, illness or taking medicine. ■ NEVER operate the saw under the influence of drugs or alcohol. WARNING WARNING WARNING WARNING WARNING ■ AVOID wearing jewelry or loose fitting clothing that may snag Failure to follow instructions in this manual may lead to serious on the controls or moving parts, this can cause a serious injury or even death! This equipment is
Streszczenie treści zawartej na stronie nr. 13
STOW CS4030 SAW — RULES FOR SAFE OPERATION ■ ALWAYS keep the work area well organized. ■ NEVER touch the hot exhaust manifold, muffler ■ Keep the saw clean. It will perform better and last longer. or cylinder. Allow these parts to cool before servicing the saw. Contact with hot! ■ ALWAYS Clear the cutting area of any debris, tools, etc. that components can cause serious burns. would constitute a hazard while the saw is in operation. WARNING WARNING WARNING WARNING WARNING DANGER DANGER DANGER
Streszczenie treści zawartej na stronie nr. 14
STOW CS4030 SAW — RULES FOR SAFE OPERATION ■ Always store equipment properly when not being used. Diamond Blade Safety Equipment should be stored in a clean, dry location out of ■ Use appropriate steel-centered diamond blades the reach of children. When storing the saw in freezing manufactured for particular use on your saw. See further weather, blow out the water lines to prevent damage to blade information in this manual. components in the water delivery system. WARNING WARNING WARNING WARNIN
Streszczenie treści zawartej na stronie nr. 15
STOW CS4030 SAW — RULES FOR SAFE OPERATION Saw Lifting and Loading Safety Towing Safety Precautions (Trailer Usage) CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION Conform to Department of Transportation (DOT) Safety This Saw is very heavy. Use proper heavy lifting procedures Towing Regulations before transporting saw on public and DO NOT attempt to lift the saw by the guards. roads. To reduce the possibility of an accident while transporting the DANGER DANGER DA
Streszczenie treści zawartej na stronie nr. 16
STOW CS4030 SAW — RULES FOR SAFE OPERATION Battery ■ ALWAYS allow the saw a proper amount of time to cool before servicing. The battery contains acids that can cause injury to the eyes and skin. To avoid eye irritation, always wear safety glasses or face ■ Prior to service, level the frame surface. shielding. Use well insulated gloves when picking the battery ■ Anytime the saw is lifted onto its nose, or tilted fully back such up. Use the following guidelines when handling the battery. as fo
Streszczenie treści zawartej na stronie nr. 17
STOW CS4030 SAW — INTENDED USE / FAMILIARIZATION Intended Use Features Operate the STOW CS4030 SAW, tools and components in ■ Tri-Position handlebars allow for 3-position adjustment for accordance with the manufacturer's instructions. Use of any optimal maneuverability. other tools for stated operation is considered contrary to designated use. The risk of such use lies entirely with the user. ■ Engine Stop Switch conveniently located on Operators The manufacturer cannot be held liable for dama
Streszczenie treści zawartej na stronie nr. 18
N N O O I I T T STOW CS4030 SAW — OPERATION AND SAFETY DECALS Machine Safety Decals The STOW CS4030 SAW is equipped with a number of operation and safety decals. These decals are provided for operator safety and maintenance information. Should any of these decals become unreadable, replacements can be obtained from your dealer. WARNING TO PREVENT SERIOUS INJURY Engine exhaust and some of DO NOT OPERATE SAW its constituents,and some dust created CAUTION by power sanding, sawing, grinding, WITHO
Streszczenie treści zawartej na stronie nr. 19
STOW CS4030 SAW — SERIAL TAG INFORMATION 1 2 MODEL SERIAL NO. Figure 4. Serial Tag/Locations Serial Tag The serial tag contains the model number and serial number of Record these numbers, in case you need to contact the the saw. The information details all parts that were included with manufacturer for information or service in the future. the saw when it was shipped from the factory, as well as the date Record your ENGINE model, (Item 2) specification number and of manufacture. serial number
Streszczenie treści zawartej na stronie nr. 20
STOW CS4030 SAW — CONTROLS AND INDICATORS 3 14 5 17 16 7 6 4 13 12 8 2 9 11 1 10 18 15 Figure 5. STOW CS4030 SAW Controls and Indicators Figures 5 and 6 show the location of the controls, indicators and 8. Depth Indicator – Indicates relative depth of blade in general maintenance parts. The function of each control, indicator surface. or maintenance part is explained below: 9. Handlebar Adjust – Loosen to move handlebar in or out. 1. FNR Handle – Use to engage the saw in a forward or backward
