Instrukcja obsługi Axxess Interface OESWC-CLASS2H

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART OESWC-CLASS2H
OESWC-CLASS2H
03-UP CLASS2 HARNESS FOR OE RF/STK
The OESWC-CLASS2H is to be used with either the OESWC-STK
or OESWC-RF. Please refer to instructions provided with
OESWC-STK or OESWC-RF for mounting instructions.
1-800-221-0932 axxessinterface.com
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

RF Wiring the OESWC interface 1. Connect the red wire to 12 volt accessory 2. Connect the Black wire to ground (you may use the same ground that you use for the aftermarket radio) Setting up the OESWC transmitter 1. Press the Red and Green buttons simultaneously for 5 seconds, and then press volume up for two seconds. This will orientate your button direction. 2. Turn on the ignition and press volume up on the OESWC transmitter. This will “marry“ the transmitter to the interface. NOTE: If y

Streszczenie treści zawartej na stronie nr. 3

5. This is the end of the auto detection stage. If the OESWC TRANSMITTER detected the vehicles radio successfully the led will light up solid red. 6. Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio. So what if the led does not light up solid red? Check out troubleshooting section below. Troubleshooting the Auto Detect Mode So you tried the auto detect feature and at the end the led did not stay on solid red, it started flashin

Streszczenie treści zawartej na stronie nr. 4

STALK Wiring of ASWCSTALK and interface 1. Connect the BLACK wires of the ASWCSTALK and the BLACK wire of the interface to ground. You may use the same ground point that is used for the radio. 2. Connect the GREEN/ORANGE and BLACK/GREEN wires of the ASWCSTALK to the corresponding wires on the interface. 3. Connect the RED wire to 12 volt accessory 4. Tap off all other unused wires on the interface. Programming the ASWCSTALK * If this is the first time the ASWCSTALK is being installed: 1. Turn

Streszczenie treści zawartej na stronie nr. 5

If the ASWCSTALK is mounted on the right side of the steering column follow the instructions below. (Auto-detect must be done first) 1. Turn the ignition on 2. Press the MODE on the ASWCSTALK for 10 seconds 3. Then press volume up for 2 seconds 4. The ASWCSTALK is now configured for the right side Troubleshooting the Auto Detect Mode So you tried the auto detect feature and at the end the led did not stay on solid red, it started flashing, or the steering wheel controls did not function proper

Streszczenie treści zawartej na stronie nr. 6

1 3 5 2 4 1. Volume up 2. Volume down 3. Seek up 4. Seek down 5. Mode (source) 3 1 5 4 2 1. Volume up 2. Volume down 3. Seek up 4. Seek down 5. Mode (source) 5

Streszczenie treści zawartej na stronie nr. 7

NOTES

Streszczenie treści zawartej na stronie nr. 8

INSTALLATION INSTRUCTIONS FOR PART OESWC-CLASS2H KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians 1-800-221-0932 axxessinterface.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 2/4/11