Streszczenie treści zawartej na stronie nr. 1
L53H2, H4/XE GB 2001, 9, 18
INSTRUCTION MANUAL
VCC-6592P
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
VCC-6594P
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual A propos de ce manuel
Before installing and using the camera, please read this manual Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel
carefully. Be sure to keep it handy for later reference. attentivement. Gardez-le à portée de main pour toute référence
ultérieure.
This manual gives basic c
Streszczenie treści zawartej na stronie nr. 2
L53H2, H4/XE GB 2001, 9, 18 Sanyo Electric Co, Ltd. 1AC6P1P2424-- Printed in Japan L53H2, H4/XE (0901KPS-DSP)
Streszczenie treści zawartej na stronie nr. 3
L53H2, H4/XE GB 2001, 9, 18 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you FEATURES need help with installation and/or settings, please consult your dealer. Built-in interline transfer method 1/3" CCD, approx. 470,000 picture elements CONTENTS Equipped with a DSP (Digital Signal Processor) function Horizontal resolution, more than 520 TV lines PRECAUTIONS..............................................
Streszczenie treści zawartej na stronie nr. 4
ENGLISH L53H2, H4/XE GB 2001, 9, 18 PRECAUTIONS In case of problem Protect from humidity and dust Do not use the camera if smoke or a strange odour comes from the To prevent damages to the camera, do not install it where there is unit, or if it seems not to function correctly. Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. Service Centre). Protect from high temperat
Streszczenie treści zawartej na stronie nr. 5
L53H2, H4/XE GB 2001, 9, 18 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) (VCC-6592P) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 3 2 Power input terminal 4 VCC-6592P: 12 V DC input terminal (12 V DC, GND) 1 VCC-6594P: 24 V AC input terminal (AC 24 V, AC 24 V, GND) 5 3 Y/C OUT connector (4 pin) 2 Separate Y (luminance) and C (chroma) signals are output from this terminal. A better picture quality is obtained if the monitor or VCR is con
Streszczenie treści zawartej na stronie nr. 6
L53H2, H4/XE GB 2001, 9, 18 PARTS NAMES 7 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 8 Flange-back adjustment screw (FLANGE BACK ADJ.) 9 7 9 Flange-back lock screw (FLANGE BACK LOCK) 8 F F Camera installation bracket 2 3 2 The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the 1 longer screws and install the shorter screws on the opposite side to sea
Streszczenie treści zawartej na stronie nr. 7
L53H2, H4/XE GB 2001, 9, 18 PARTS NAMES G Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. H H Camera setup section (under the cover) G These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixin
Streszczenie treści zawartej na stronie nr. 8
L53H2, H4/XE GB 2001, 9, 18 CONCERNING AUTO-IRIS LENSES DC type auto-iris lens VR301 A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) DC VIDEO VIDEO type auto-iris lens A. I. LENS A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens
Streszczenie treści zawartej na stronie nr. 9
L53H2, H4/XE GB 2001, 9, 18 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens 2 L 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens 3 To allow for flange-back adj
Streszczenie treści zawartej na stronie nr. 10
L53H2, H4/XE GB 2001, 9, 18 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. 1 Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout DC type lenses VIDEO type lenses Brake coil (–) +12 V DC (50 mA max.) 1 2 1 2 1 Brake coil (+) Not
Streszczenie treści zawartej na stronie nr. 11
L53H2, H4/XE GB 2001, 9, 18 CONNECTIONS (VCC-6592P only) 1 (A) (A) 2A (A) 2A 12 V DC + – 2 (Video signal connections) 12 V DC connection (B) 2A 3 : VIDEO IN Push to insert the cable : VIDEO OUT 12 V DC input 3 Insert the plug of this power cord into a wall outlet. Basic connection for monitoring or recording The POWER indicator (A) will light. Adjust the picture on the The peripheral devices (VCR, monitor, lens, etc.) and cables are monitor using the Brightness and Contrast control
Streszczenie treści zawartej na stronie nr. 12
L53H2, H4/XE GB 2001, 9, 18 CONNECTIONS (VCC-6592P only) 1 (A) (A) 2A 12 V DC – + 2 (Video signal connections) 12 V DC connection (B) 3 2A : VIDEO IN Push to insert the cable : VIDEO OUT 12 V DC input 3 The POWER indicator (A) will light. Adjust the picture on the Connections to the camera Y/C OUT connector monitor using the Brightness and Contrast controls. The peripheral devices (VCR, monitor, lens, etc.) and cables are CAUTION: sold separately. Please use a monitor with a Y/C
Streszczenie treści zawartej na stronie nr. 13
L53H2, H4/XE GB 2001, 9, 18 CONNECTIONS (VCC-6594P only) 1 (A) 3 2A AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) ~ ~ GND 2A : VIDEO IN : VIDEO OUT 3 Insert the plug of this power cord into a wall outlet. Basic connection for monitoring or recording The POWER indicator (A) will light. Adjust the picture on the The peripheral devices (VCR, monitor, lens, etc.), AC adaptor monitor using the Brightness and Contrast controls etc. and cables are sold s
Streszczenie treści zawartej na stronie nr. 14
L53H2, H4/XE GB 2001, 9, 18 SETTINGS (VCC-6592P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 7-a 9 Control name Position High speed electronic shutter (ES)/ 1/50 sec. 1 Electronic iris (EI) setting R B VR301 VR302 VR303 ON Auto gain control setting (HI/NO
Streszczenie treści zawartej na stronie nr. 15
L53H2, H4/XE GB 2001, 9, 18 SETTINGS (VCC-6594P only) The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 9 Control name Position High speed electronic shutter (ES)/ 1/50 sec. 1 R B VR301 Electronic iris (EI) setting VR302 VR303 ON Auto gain control setting (HI/NORM)
Streszczenie treści zawartej na stronie nr. 16
L53H2, H4/XE GB 2001, 9, 18 SETTINGS Table A (switch 1 ~ 3) Electronic shutter settings and electronic iris 1 2 3 4 5 6 7 8 settings 1/50(AI) 1/120 1/500 1/1000 1/2000 1/4000 1/10000 EI When all of these switches are down, electronic shutter (1/50 sec or auto iris setting) is enabled. The electronic shutter can be set to one 12 3 1 23 1 23 1 23 12 3 1 23 1 23 1 23 of 7 speeds as shown in Table A. (Unit: sec.) Furthermore, when all switches are up, electronic iris setting is enabled. Automatic Ga
Streszczenie treści zawartej na stronie nr. 17
L53H2, H4/XE GB 2001, 9, 18 SETTINGS (MULTI mode: 64 sections) Backlight compensation setting This camera has two different backlight compensation functions: Normally backlight compensation switch 6 (MULT) and 7 (CENT) are set to the down (OFF) position. Change the backlight compensation switch settings 6 7 depending on the conditions. MULT mode: Use this position when applying backlight compensation to the whole of the screen. (CENT mode) CENT mode: Use this position when applying backlight
Streszczenie treści zawartej na stronie nr. 18
L53H2, H4/XE GB 2001, 9, 18 SETTINGS White balance adjustment External sync adjustment (VBS) (VCC-6592P only) Normally the switch 8 (WB) is set to the down (ATW: auto white 1 Connect the VBS signal output for the other camera to the VBS balance) position and the white balance is adjusted automatically. If a IN connector at the rear of this camera. manual white balance adjustment is necessary, follow the steps below. 2 If the signals are not synchronized, change the sub-carrier (SC-P1) Set the sw
Streszczenie treści zawartej na stronie nr. 19
L53H2, H4/XE GB 2001, 9, 18 SETTINGS Lens iris adjustment Line phase adjustment (VCC-6594P only) If using a DC type auto-iris lens, you will need to set the LEVEL When using a camera switcher to connect 2 cameras or more to one (VR301) volume when shooting in the conditions described below. monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. 1 Set the switch 9 (SYNC) to the up (LL) position. VR301 2 Switch the display on the monitor from cam
Streszczenie treści zawartej na stronie nr. 20
L53H2, H4/XE GB 2001, 9, 18 TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen Is the power turned on to all connected devices? Is the voltage correct? Are all the signal connecting cables correctly connected? Is the lighting sufficient? Has the lens cap been removed? Is the lens t
