Streszczenie treści zawartej na stronie nr. 1
Assembly Instructions for Model: WFV44
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is
constructed of real hardwood and resonance dampening MDF.
Safety Warning: If you do not understand these directions, or have any doubts about the
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or
www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our
customer service representatives
Streszczenie treści zawartej na stronie nr. 2
Parts List (Cont) (2) Bottom Shelf - q (2) Mid Shelf - r (2) Glass Panel - t (2) Small Door - s (2) Back Panel - x (1) Left Side Panel - u (1) Right Side Panel - v (1) Center Panel - w Step 1: Prepare the Side Panels and Center Panel Thread a Cam Pin (a) into each of the smaller holes in each Panel (u,v,w). Tighten each Cam Pin with a Phillips screw driver. Insert a Dowel (d) into the larger ad
Streszczenie treści zawartej na stronie nr. 3
Step 2: Prepare Stretchers Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the Stretchers. See Diagram 2 for assistance. Diagram 2 Detailed View o a arrow p Step 3: Add Stretchers Add the Front and Back Stretchers (o,p) to the Side Panel (u), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and the Dowel g
Streszczenie treści zawartej na stronie nr. 4
Step 4: Add Center Panel Press fit the Center Panel (w) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Center Panel. See Diagram 4 for assistance. Note: Make sure the hinge holes on the Center Panel are on the same side as the Front Stretchers. Detailed View Diagram 4
Streszczenie treści zawartej na stronie nr. 5
Step 6: Add Side Panel Press fit the Side Panel (v) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel (d) going into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Side Panel. See Diagram 6 for assistance. Note: Make sure the hinge holes on the Side Panel are on the same side as the Front Stretchers. Detailed View Diagram 6
Streszczenie treści zawartej na stronie nr. 6
Step 8: Add Top Gently tap a Dowel Pin (c) into the holes on the top of each Panel (u,v,w). Slide a Spacer (g) over each Dowel Pin. Press fit the Top (n) so it fits onto the Dowel Pins. See Diagram 8 for assistance. Detailed View Diagram 8 n c g v Step 9: Prepare Doors Insert each Phillips Bolt (h) through the Door (s) and into the Door Handle (i). Tighten with a P
Streszczenie treści zawartej na stronie nr. 7
Step 10: Door Install Position the Door (s) so the holes in the Hinge Plate (m) line up with the front pair of holes in the Side Panel (u,v). Insert a Hinge Plate Screw (k) through the Hinge Plate and thread it into each hole in the Side Panel. Tighten with a Phillips screw driver. Repeat process so each Hinge Assembly is secured. See Diagram 10 for assistance. Detailed View Diagram 10 s m k u Ste
Streszczenie treści zawartej na stronie nr. 8
Step 11: Add Back Panel Position each Back Panel (x) up against the assembly and thread a Wood Screw (f) through it and into the Back Stretcher (p). Repeat process until each Back Panel is secured with four Wood Screws. Tighten each with a Phillips screw driver. See Diagram 11 for assis- tance. Detailed View Diagram 11 p f x
