Streszczenie treści zawartej na stronie nr. 1
AUTOMATIC TRANSMISSION REMOTE STARTER
SYSTEM
AS-6205 SH
Installation Guide
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from
improper installation of the product, be that either damage to the vehicle itself or to the
Unit. This Unit must be installed by a certified technician using all safety devices
supplied. Please note that this guide has been written for properly trained Autostart
technicians, a certain level of skill and knowledge is th
Streszczenie treści zawartej na stronie nr. 2
Table of Contents nd nd Introduction..................................................... 3 Fifth Relay Output (2 IGN or 2 ACC or nd Included in the Package ................................. 3 2 START)............................................... 15 Before You Get Started…............................... 4 Ignition-Controlled Door Locks................. 16 Installation Points To Remember ................... 4 Secure Lock.............................................. 16 Harness Description ...
Streszczenie treści zawartej na stronie nr. 3
Introduction This Guide contains all information pertinent to the installation. Most (if not all) features are grouped in the User Guide and therefore, should you need information on a feature, you should refer to the User Guide Included in the Package Please review the Installation Guide before beginning the installation, particularly the Wiring Schematic and the Programming Options. It is very important that you familiarize yourself with the programming and the operation of the syste
Streszczenie treści zawartej na stronie nr. 4
Before You Get Started… On vehicles with a manual Transmission, When wiring in parallel, make sure to isolate always ensure that all Doors will get the Unit out each connection with a diode in order to avoid of Ready Mode. Switch the wire used so that it feedback and possible damage. is triggered by all Doors. Examples: Make sure that the Parking Brake and Door Wiring a clutch bypass and a Transponder Switch contacts work properly. Module to the Ground Out when Running When worki
Streszczenie treści zawartej na stronie nr. 5
6-Pin Main Ignition Harness Wire Description Connect to the largest 12 V supply wire at the Ignition harness. Ensure that the OEM power wire is fused for more than 30 A. RED NOTE: certain new vehicles have no suitable 12 volts source at the A +12 V Battery IGNITION switch (the 12 Volt wire is too small to supply the necessary current). In this case, the fuse box, or the B+ connection on the battery is recommended. PURPLE Connect to the Starter wire of the vehicle (at the IGNITION switch)
Streszczenie treści zawartej na stronie nr. 6
“under crank”. GRAY Connect this wire to the Hood Pin-switch supplied. This input will disable or (-) Hood 3 shut down the Remote Starter when the Hood is opened. It is also used for Switch programming and therefore it is essential that it is installed. input This wire must be connected to the Brake Light switch of the vehicle. The ORANGE (+) Brake wire should be +12 V only while the Brake Pedal is pressed. This input will 4 Switch shut down the Remote Starter if the Brake Pedal is pres
Streszczenie treści zawartej na stronie nr. 7
The unit is equipped with a selectable passive- or active-arming Starter Kill circuit that will immobilize the vehicle when the system is armed. This wire will provide a constant 500-mA negative output when the system is armed (locked by remote) or if remote started. This wire should be connected to a Single Pole Double-Throw Relay (This wire WHITE / ORANGE will connect to Pin 85, on the Relay, and Pin 86 will be connected to the 7 (–) Starter Ignition wire). Kill output A second ben
Streszczenie treści zawartej na stronie nr. 8
This positive input will monitor the Glow Plug Light in Diesel Mode: it will wait until the Glow Plug Light goes out to crank the Engine. Connect to the side of the Glow Plug Light that is positive when the Light is on. Note: In Diesel Mode there is a 18-sec. crank timing delay (or approximately 25-sec. if the run time is set to 30 min.): if the Glow Plug Light is still on after the delay expires, the Module will proceed to start the Engine. (Also known as the “wait-to-start light”.) The
Streszczenie treści zawartej na stronie nr. 9
output ON for a 30-second cycle and shuts off automatically unless the user presses LOCK and UNLOCK before the end of that cycle, at which point, the AUX2 output shuts off. This output can also be used as Priority Door Unlock. Car Finder is enabled or disabled in the AUX 2 function programming. 500 mA negative Parking Light output YELLOW Note: Ensure that the voltage does not vary when the dimmer control 2 (-) Parking Light switch is turned up or down. If this is the case, it is not the
Streszczenie treści zawartej na stronie nr. 10
The Programming Assistance Button (A.k.a. PAB.) The PAB is located on the side of the Module. This push button mimics the Hood-Pin switch in order to avoid having to get out of the vehicle and pressing the Hood-Pin switch. The PAB will work only when the Hood is up. How to Program the Transmitter. 1. FLASH the Hood Pin Switch. Before the 20 seconds have passed, turn the Ignition Key to the IGNITION ON (RUN) position. Turn the IGNITION to OFF. 2. Press and hold the LOCK button until the vehicle
Streszczenie treści zawartej na stronie nr. 11
The Module can only be programmed Function by Function. After selecting a Mode (from 1 to 3), you will be taken to the first Function of that Mode. After entering an Option number for Function 1, you will be automatically taken to Function 2, and so on; therefore, be ready to re-enter all option numbers for all functions of the Mode you are accessing. You may not skip Functions. For each Function, select one of the four Options by pressing the corresponding button on the Transmitter: L
Streszczenie treści zawartej na stronie nr. 12
nd th th All Doors unlock upon the 2 , 4 , 6 … pressing of the UNLOCK button. Mode 2 *indicates default setting Function 1 – Home Valet Mode OPTION 1 Home Valet enabled OPTION 2* Home Valet disabled OPTION 3 Home Valet disabled Function 2 – Safe Start OPTION 1 Safe Start enabled OPTION 2* Safe Start disabled OPTION 3 Swap Start – increased safety mode: To Start: press Lock and Unlock buttons simultaneously. Press the START button to activate AUX 2. Function 3 – Engine Run Time OPTI
Streszczenie treści zawartej na stronie nr. 13
OPTION 2* Ignition Valet - ENABLED OPTION 3 Ignition Valet - ENABLED Horn Honk / Siren Timing (Optional) 1. Make sure that Mode 3 Function 4 Option1 or Option 3 is activated. 2. FLASH the Hood Pin Switch Before the 20 seconds have passed, 3. Press and hold the Brake Pedal. Press the START and UNLOCK buttons simultaneously on the Transmitter. The Horn/Siren will sound 5 times. 4. Release the Brake Pedal. 5. To change the timing: a. To increase the Horn Honk/Siren by 3 ms, press the LO
Streszczenie treści zawartej na stronie nr. 14
Table 5 Multi-Speed Tach Programming No manual adjustments are necessary. However, you should go through the Tach programming procedure every time a new Unit is installed. 1. FLASH the Hood Pin Switch. 2. Press and hold the Brake Pedal. Press the LOCK and UNLOCK buttons simultaneously on the Transmitter. The Parking Lights will flash 4 times the Horn/Siren will sound 4 times (if programmed). Release the Brake Pedal. 3. Start the vehicle and let it to reach regular Engine-idle speed.
Streszczenie treści zawartej na stronie nr. 15
Away. A medium “tap” should trigger the Warn Away. A hard “tap” should trigger the Alarm. All vehicles are different and therefore transmit shock level differently, if you are unable to set both zones to your satisfaction, referrer to p.12 (Function 4 – Shock Sense / Warn Away ) to disable the appropriate zone(s). When the Engine is running after remote start the Shock Sensor will not trigger an Alarm condition, although it will still produce warning chirps if Warn-away is enabled.
Streszczenie treści zawartej na stronie nr. 16
Caution! Do not use more than one of the three sets of jumper pins simultaneously. The relay output rating on this Unit is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, causing the 30A fuse to blow. Using a digital voltmeter, check the Starter wire for amperage when vehicle is cranking. Ignition-Controlled Door Locks Ignition Lock disabled: turns OFF the Ignition Lock feature. Ignition Lock enabled: locks all Doors when the key is in the ON position and t
Streszczenie treści zawartej na stronie nr. 17
Safe Start (Child Safety Mode) (OFF by default.) Requires the user presses the START button on the Transmitter twice within 3 seconds in order to start the vehicle. If the Special Safe Start Mode is selected (SWAP Start): To start the vehicle, press the LOCK and UNLOCK buttons simultaneously. Pressing the START button triggers AUX2. START button becomes AUX2 trigger and the AUX2 button becomes the START trigger. Table 9 Siren or Horn Chirps The Siren can be set to any one of the follow
Streszczenie treści zawartej na stronie nr. 18
Disarmed Notification This feature will notify the user when the vehicle is left disarmed after Ignition is turned off, or when the Module is disarmed after being previously armed, the opening or closing of a Door will cause the Horn or the Siren to sound once after 10 sec. to warn the user that the vehicle was left unprotected. Pressing LOCK or UNLOCK will cancel this timer. Two-Stage Disarm When the Siren is sounding, pressing UNLOCK will stop the siren – but without unlocking or disar
Streszczenie treści zawartej na stronie nr. 19
10 x = Alarm condition Intrusion Codes 1 x = Power-up Reset: Battery disconnected / reconnected or dead… 2 x = Doors intrusion 3 x = Shock Sense 4 x = Hood 5 x = Panic 6 x = Ignition Note: “x” stands for one flash of the Parking Lights Intrusion Codes via LED light If there has been an intrusion in the vehicle while it was locked and armed, the LED will provide an intrusion code corresponding to the type of the intrusion which took place. The LED intrusion codes are flashed in c
Streszczenie treści zawartej na stronie nr. 20
Diagnostics - Parking Lights Flash Rate Flashes Description Doors locked, Starter Kill armed. End of Run Time. TRUNK button pressed 1 START signal received by the Module. Cold Weather Mode cancelled. Cannot start after maximum number of attempts is reached. Run Time cancelled. 2 Remote start attempt cancelled by remote. Doors unlocked, Starter Kill disarmed. 3 Entering Cold Weather Mode +12 volts detected on the Brake line; cranking cancelled 4 Entering Tach Learning N
