Streszczenie treści zawartej na stronie nr. 1
69802 G
Gas Hob
Operating Instructions
GB
PERFECT IN FORM AND FUNCTION
AUS ERFAHRUNG GUT
Streszczenie treści zawartej na stronie nr. 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob. Ensure that the gas and electrical supply complies
Streszczenie treści zawartej na stronie nr. 3
Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. Never use plastic or
Streszczenie treści zawartej na stronie nr. 4
Contents Important Safety Information ................................................................................ 2 Instructions for the User ........................................................................................ 5 Description of the Hob ............................................................................................... 5 Operation.................................................................................................................... 6 Maintenance a
Streszczenie treści zawartej na stronie nr. 5
Description of the Hob 13 3 5 6 7 8 4 2 1. Hob Top 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) INSTALLATION Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations. The relevant instructions are to be found in the se
Streszczenie treści zawartej na stronie nr. 6
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. Each control knob is equipped with a pilot light which gradually lights up according to the heat level that you select with the control knob. When switching on the mains, after i
Streszczenie treści zawartej na stronie nr. 7
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Pan Supports To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in the diagram. The pan supports are dishwas
Streszczenie treści zawartej na stronie nr. 8
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the Check that the unit is plugged in and gas the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning. The gas ring burns unevenly Check the
Streszczenie treści zawartej na stronie nr. 9
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3. Clear and c
Streszczenie treści zawartej na stronie nr. 10
Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. • The appliance has
Streszczenie treści zawartej na stronie nr. 11
Instructions for the Installer Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: 580 mm. Depth: 510 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. IGNITION HT SPARK Spark Generator Ispra Control's BF 50046 - 230-240V 0.6 YA
Streszczenie treści zawartej na stronie nr. 12
Instructions for the Installer BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) TYPE OF GAS POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1.9 0.45 1.0 0.33 NATURAL GAS 20 mbar NOMINAL FLOW 3 VALUE = RATE m /h 0.276 0.062 0.181 0.043 0.095 0.031 3 37.78 MJ/m NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 3 Ws - 50.7 MJ/ m 1/100 mm NOMINAL THERMAL LPG GAS POWER kW 2.7 0.65 1.9 0.45 1.0 0.33
Streszczenie treści zawartej na stronie nr. 13
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm 600 mm Instructions for the Installer Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom or shower room. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm. between the rear edge of the hob and the wall. A minimum distance of 100 mm. must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fit
Streszczenie treści zawartej na stronie nr. 14
Instructions for the Installer FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male t
Streszczenie treści zawartej na stronie nr. 15
Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams FO 2847 1 and 2. ON/OFF SWITCH ON/OFF SWITCH 1 2 FLEX OUTLET FLEX OUTLET FO 076
Streszczenie treści zawartej na stronie nr. 16
Instructions for the Installer Building over a kitchen unit with door Proper arrangements must be taken in 3 designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is a 60 shown in diagram 3. The panel fitted under the hob ("a") b should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. Fitting the hob to
Streszczenie treści zawartej na stronie nr. 17
Instructions for the Installer Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated o
Streszczenie treści zawartej na stronie nr. 18
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces wit
Streszczenie treści zawartej na stronie nr. 19
Instructions for the Installer Blue Fault Finding Brown Green Yellow Preliminary Electrical Systems Check START Blue Isolate appliance Green and carry out: Brown Yellow A: Earth Continuity check. Carry out: NO YES Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. NO YES PLUG (with cover removed) SOCKET (face view) Inlet wiring Earth Wire faulty. Green/Yellow ( ) Rectify any ( ) E fault. Neutral Wire Blue N L Isol
Streszczenie treści zawartej na stronie nr. 20
Instructions for the Installer A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance te
