Instrukcja obsługi Metra Electronics 99-7502

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7502
APPLICATIONS
Mazda MPV 2000-2006
99-7502
KIT FEATURES
• DIN Mount Radio Provision
• ISO Mount Radio Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate
C
B
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

99-7502 TABLE OF CONTENTS Dash Disassembly - Mazda MPV 2000-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket

Streszczenie treści zawartej na stronie nr. 3

99-7502 DASH DISASSEMBLY MAZDA MPV 2000-2006 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Remove (2) Phillips head screws from above instrument cluster. (Figure A) 3 Unclip and remove the radio trim panel. (Figure B) 4 Remove (4) Phillips screws securing the radio. Unplug and remove radio. B (Figure C) Continue to kit assembly. C 1

Streszczenie treści zawartej na stronie nr. 4

99-7502 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. B 2

Streszczenie treści zawartej na stronie nr. 5

99-7502 KIT ASSEMBLY ISO DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing assembly. (Figure B) Continue to final assembly. B 3

Streszczenie treści zawartej na stronie nr. 6

99-7502 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Streszczenie treści zawartej na stronie nr. 7

99-7502 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

99-7502 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 10/12/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7502