Instrukcja obsługi Epson ELPMBP01

Streszczenie treści zawartej na stronie nr. 1

Installation and Assembly:
Adjustable Suspended Ceiling Channel Kit
This product is UL Listed. It must be
Model: ELPMBP01
installed by a qualified professional

installer.
Maximum UL Load Capacity: 50 lb (22.6 kg)
Manufactured by Peerless Industries, Inc.
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Streszczenie treści zawartej na stronie nr. 2

NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands

Streszczenie treści zawartej na stronie nr. 3

Before you start check the parts list to insure all of the parts shown are included. NOTE: You may not need all hardware provided. Parts List Description Qty.Part # ceiling tray 055-0492 A 1 B 1/4"-20 x 3/8" screws 4 520-2015 C 1/4"-20 nuts 4 530-9302 allen wrench 1 560-9706 D E escutcheon ring 1 1418-001A F turnbuckle 4 560-9620 12 gauge x 20' (6.1m) tie wire (not shown) 1 600-2008 G H eye bolt 5 580-0006 I concrete anchor 5 580-0005 flush mount tube 1 1446-014 J K M5 x 10 mm penta pin screw 1

Streszczenie treści zawartej na stronie nr. 4

Installation to Suspended Ceiling Place ceiling tray (A) in grid above 24" x 24" or 24" x 48" false ceiling tile IMPORTANT PRE-ASSEMBLY 1 so that lip of ceiling tray (A) rests on ceiling runners as shown in figure 1. INFORMATION: Place in desired position and tighten knurled knobs until ceiling tray (A) is securely attached to ceiling runners. Ceiling Tray (A) is designed to fit above a 24" (610 mm) x 24" (610 Slide collar mount plate to desired position. Using hole in collar mount mm) section o

Streszczenie treści zawartej na stronie nr. 5

Anchoring Ceiling Plate Cut tie wire (G) into four pieces of equal length. Insert wires through ends of turnbuckles and loop. Twist each wire 4 around itself at least six times. Drill holes for four ceiling anchors (see "Various Anchoring Methods"). Position the holes so that when the tie O wires (G) are attached and taut will angle out at 15 . Pull tie wires tight and loop though turnbuckles of the ceiling anchors (or truss). Again twist each wire around itself at least six times. When this s

Streszczenie treści zawartej na stronie nr. 6

LIMITED FIVE-YEAR WARRANTY www.peerlessmounts.com © 2007 Peerless Industries, Inc. ISSUED 03/17/06 LIT-0190E 6 of 6 ISSUED: 02-13-08 SHEET #: 128-9029-2 07-10-08 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870. © 2008, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective