Streszczenie treści zawartej na stronie nr. 1
Liquid Crystal Projector
Model name
CP-S833W/E
OPERATING GUIDE
Thank you very much for purchasing this hitachi Liquid Crystal Projector.
Please read this operating guide to use correctly. After reading this manual, keep it carefully for
future reference.
Outline
Contents Page
Before use ............................3
This Liquid Crystal Projector can display various
computer signals and NTSC/PAL/SECAM video Names and functions of each
signals.
part ................................7
Installation
Streszczenie treści zawartej na stronie nr. 2
FOR THE CUSTOMERS IN U.K THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating.
Streszczenie treści zawartej na stronie nr. 3
WARNING:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications, Operatio
Streszczenie treści zawartej na stronie nr. 4
[Safety precaution] Warning If any abnormality occurs. Do not look directly at the lens when · When there is an abnormal smell or smoke, if the lamp is lit. you use this unit as it is, this could cause a fire Do not look directly at the lens when or electric shock, etc. When an abnormality is the lamp is lit. Since a strong light found, immediately turn off the power switch is used, it could damage you vision, etc. and pull out the power plug from the power Especially pay attention if children
Streszczenie treści zawartej na stronie nr. 5
Warning · If the cord is damaged (core wire is Be careful in handling the power cord. exposed, disconnected, etc.), ask · Do not scratch, damage or process the power your dealer to replace it. It may cord. Do not bend it forcibly. Also do not put a cause a fire, electric shock, etc. heavy object on it, do not heat it and do not pull · Check that no dirt adheres to the it. If you do, the power cord may be damaged and power plug and fully insert without any play. If it may cause a fire, electric s
Streszczenie treści zawartej na stronie nr. 6
Caution Use of batteries. Caution when replacing the lamp. · Do not use batteries not specified · When replacing the lamp, turn off the power of for this unit. Do not use new the projector and disconnect the power plug batteries mixed together with old from the power outlet. Then wait for ones. This may cause a fire, injury 45 minutes to allow the lamp cool: due to burst of battery, liquid Failure to do so could result in a leakage. burn. For disposal of used lamp, treat · When inserting batter
Streszczenie treści zawartej na stronie nr. 7
Names and functions of each part Main unit MENU button Picture adjustments. Refer to page 15~18 for details. RESET button INPUT button Resets unit to factory settings. To select the input source. (See page 15) RESET Each time this button is pressed, the input source is changed in sequence as shown below. MUTE button Silences the sound. (Cancels the mute RGB1 RGB2 VIDEO1 VIDEO2 MENU when the unit is set in mute mode.) MUTE INPUT LAMP indicator TEMP indicator This lights or blinks when the lamp do
Streszczenie treści zawartej na stronie nr. 8
Names and functions of each part (continued) Remote control sensor AC IN socket MAIN POWER switch Connect the provided power cord. Main power ON/OFF switch. : OFF : ON RGB input terminal D-sub 15pin shrink terminal (1/2) RGB output terminal D-sub 15pin shrink terminal RGB output can be displayed even in the standby mode. INPUT RGB IN RGB OUT S-VIDEO VIDEO input terminal 1 1 2 (on video-equipped models only) VIDEO S-VIDEO input terminal CONTROL Mini DIN 4pin connector (1/2) 1 2 VIDEO input termi
Streszczenie treści zawartej na stronie nr. 9
Names and functions of each part (continued) Remote control transmitter MUTE button STANDBY / ON button Silences the sound. (Cancels the mute when Power ON/OFF button. the unit is set in mute mode.) OFF sets the unit in standby mode. STANDBY/ON MUTE (See page 12, 13) VOLUME button Adjusts volume. The sound is loud or low FREEZE Button FREEZE while pressing the "+" or "-" button. Pressing this button displays a still picture LASER button (by freezing). (See page 14) VOLUME MAGNIFY Laser pointer O
Streszczenie treści zawartej na stronie nr. 10
Names and functions of each part (continued) How to insert batteries Insert the provided batteries (LR6 (alkal) into the remote control transmitter. Insert the batteries Remove the battery as illustrated inside compartment cover. the battery compartment. Slide the battery compartment cover Replace the cover. in the direction of the arrow while pressing slightly down on it. Cautions on use of batteries Caution Cautions on use Caution · Do not use batteries not specified for this unit. · Do no
Streszczenie treści zawartej na stronie nr. 11
Installation Example of the projector and screen installation Determine picture size and projection distance as illustrated below. View from the side View from the top Screen Lens center a a:Distance from the projector to the screen. (tolerance : ±10%) a (inch) Screen (inch) This screen size is full-screen size.(800 dots X 600 dots) Minimum Maximum Installation of liquid crystal projector 40 67 87 60 98 130 Please basically use liquid crystal projector at the horizontal position. 80 130 173
Streszczenie treści zawartej na stronie nr. 12
Basic operations To project the picture STANDBY/ON MUTE 2 FREEZE 4 RESET MAGNIFY VOLUME OFF MENU 3 POSITION ON LASER MUTE INPUT ON LAMP TEMP 7 STANDBY/ON 5 RESET RIGHT MENU ON MOUSE ON BLANK TIMER 7 2 RGB VIDEO INPUT 1 Turn the MAIN POWER switch of the projector on.[ I : ON] 1 · The ON indicator will light up orange. Press the STANDBY/ON button. 2 · The ON indicator blinks (green) and then lights (green). · The ON indicator will blink green during warm-up and light up. · Power cannot be turn
Streszczenie treści zawartej na stronie nr. 13
Basic operations (continued) To turn off the power STANDBY/ON MUTE 1 FREEZE RESET MAGNIFY VOLUME OFF 3 MENU POSITION ON LASER MUTE INPUT ON LAMP TEMP STANDBY/ON RESET RIGHT MENU ON MOUSE ON BLANK TIMER 1 RGB VIDEO INPUT 2 Press the STANDBY/ON button, for 1 second. 1 · The ON indicator lights up orange and the lamp turns off. (About 1 minute later), the fan stops and the indicator blinks orange. · Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in st
Streszczenie treści zawartej na stronie nr. 14
Basic operations (continued) FREEZE FUNCTION STANDBY/ON MUTE This function can display a still picture (by freezing). This function can be used in combination with a MAGNIFY function. FREEZE 1, 2 MAGNIFY VOLUME Press the FREEZE button. OFF 1 The display image stops. A mark appears at the lower right of POSITION ON LASER the screen for about 3 seconds during the FREEZE function. [TO RELEASE FREEZE] Press the FREEZE button. 2 The freeze function is cancelled. Furthermore, a mark appears a
Streszczenie treści zawartej na stronie nr. 15
Adjustments and functions STANDBY/ON MUTE FREEZE RESET VOLUME MAGNIFY OFF MENU POSITION ON LASER MUTE INPUT ON LAMP TEMP 2, 3 STANDBY/ON RESET RIGHT MENU ON MOUSE ON 1 1, 2, 3 BLANK TIMER RGB VIDEO INPUT Press the MENU ( ) buttons or the MENU ON / 1 OFF button. · On-screen menus are displayed on the screen. Select the menu to be adjusted using the MENU ( ) 2 buttons or DISK PAD. · Menu displayed in green is selected. Select the item to be adjusted using the MENU ( ) 3 buttons or DISK PAD. ·
Streszczenie treści zawartej na stronie nr. 16
Adjustments and functions (continued) SET UP The menu SET UP serves for the change of parameters influencing the picture and for the move picture position. RGB signal input VIDEO signal input SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. VOLUME VOLUME BRIGHT BRIGHT CONTRAST CONTRAST V POSIT 121 SHARPNESS 57 H POSIT COLOR H PHASE 7 TINT H SIZE 800 COLOR BAL R B COLOR BAL R B Adjustment Item Details of adjustment VOLUME Decrease
Streszczenie treści zawartej na stronie nr. 17
Adjustments and functions (continued) INPUT The menu INPUT serves for the selection of input source. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. SYSTEM AUTO RGB1 RGB1 NTSC RGB2 RGB2 PAL VIDEO1 V I DEO1 SECAM VIDEO2 V I DEO2 NTSC4.43 M-PAL Adjustment Item Details of adjustment RGB 1 Selects the RGB 1 terminal. RGB 2 Selects the RGB 2 terminal. VIDEO 1 Selects the VIDEO 1 terminal. VIDEO 2 Selects the VIDEO 2 terminal. Selects the video signal systems. SYSTEM When the picture (Video) is a
Streszczenie treści zawartej na stronie nr. 18
Adjustments and functions (continued) OPT. The menu OPT. allows you to control communication function etc. SETUP INPUT IMAGE OPT. COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF START UP SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. 1200 7N1 COM. SPEED COM. BITS 2400 8N1 (bps) 15 min. TIMER 4800 9600 19200 SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. LANGUAGE ENGLISH START UP TURN ON FRANÇAIS TURN OFF AUTO OFF 0 mi
Streszczenie treści zawartej na stronie nr. 19
Connection to the video signal terminals 1. Input signal Luminance signal 1.0Vp-p, 75W termination S-VIDEO signal Chrominance signal 0.286Vp-p (burst signal), 75W termination VIDEO signal 1.0Vp-p, 75W termination 200mVrms, 20kW below (MAX 3.0Vp-p) Input AUDIO signal Output 0~200mVrms, 1kW 2. Signal input terminal Chrominance signal Luminance signal Ground Ground S VIDEO input (Mini DIN4 pin) Video input signal terminals have priority in the following order. Caution 1 2 S-VIDEO input terminal
Streszczenie treści zawartej na stronie nr. 20
Connection to the RGB signal terminal(continued) 3. Example of computer signal Resolution fH fV Standard Display Dots Note 1 Note 2 Note 3 H X V (kHz) (Hz) Type H X V 640 X 350 31.5 70.1 VGA-1 Expanded 800 X 490 NEC 640 X 400 24.8 56.4 Expanded 800 X 560 PC9800 640 X 400 31.5 70.1 VGA-2 Expanded 800 X 560 640 X 480 43.3 85.0 VESA Expanded 800 X 600 640 X 480 31.5 59.9 VESA VGA-3 Expanded 800 X 600 Mac13" SW 1 ON 640 X 480 35.0 66.7 Expanded 800 X 600 mode SW 2 ON 640 X 480 37.9 72.8 VESA Expande
