Streszczenie treści zawartej na stronie nr. 1
®
Unpacking and Setup Guide
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking and Assembling Stylus Pro 9600. . . . . 2
Unpacking and Assembling Stylus Pro 7600. . . . . 8
Setting up Stylus Pro 7600/9600 . . . . . . . . . . . . . . 13
Using the User Guides . . . . . . . . . . . . . . . . . . . . . . 20
4020360-00
Copyright ©2002 by SEIKO EPSON CORPORATION, Nagano, Japan
EUL
Streszczenie treści zawartej na stronie nr. 2
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. Neither SEIKO EPSON CORPORATION nor its affiliates shall
Streszczenie treści zawartej na stronie nr. 3
❏ Keep the printer away from the dusty areas. Safety Instructions ❏ Place the printer near a wall outlet where the plug can be easily unplugged. Important Safety Instructions When using the printer Read all of these instructions before using your ❏ Do not put your hand inside the printer or printer. Also be sure to follow all warnings and touch the ink cartridges during printing. instructions marked on the printer. ❏ Do not move the print heads by hand; ❏ Do not block or cover the openings
Streszczenie treści zawartej na stronie nr. 4
For United Kingdom Users Warnings, Cautions, and Notes Warnings must be followed carefully to avoid Use of options w bodily injury. EPSON (UK) Limited shall not be liable against Cautions must be observed to avoid damage to any damages or problems arising from the use of c your equipment. any options or consumable products other than those designated as Original EPSON Products or Notes contain important information and useful tips EPSON Approved Products by EPSON (UK) on the operation of
Streszczenie treści zawartej na stronie nr. 5
❏ Operate the printer under the following Parts: conditions: AB Temperature: 10 to 40ºC Humidity: 5 to 85% without condensation ❏ Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust. ❏ Do not block the ventilation openings. ❏ Avoid locations near potential sources of C interference such as loud speakers or cordless phones. ❏ Avoid locations near TVs, radios, air conditioners, or humidifiers. ❏ Keep the printer away from combustible D substances. Deciding
Streszczenie treści zawartej na stronie nr. 6
2. Referring the Step 1, fix the other strut to the Tools: base. G 3. Fasten four screws on the both sides of the base upright securely. This completes assembly of the base unit. Before H attaching the paper basket, mount the printer on the base unit. I Unpacking the printer J Caution: c The printer unit is heavy and unwieldy. Have two people unpack the printer unit, and four people place the printer unit on top of the base G: Hex wrench unit. H: Hex socket head bolts (4) 1. Remove the ac
Streszczenie treści zawartej na stronie nr. 7
3. Take out the cardboard panels from around R the printer. M: Roll paper spindle N: Roll paper (EPSON Doubleweight Matte Paper; 5 m) O: Ink cartridges (Yellow, Cyan, Magenta, Light Cyan, Light Magenta, Black1, Black2) 4. Remove the polystyrene foam stoppers under the printer. P: Roll paper belt (for keeping roll paper wound up) Q: Power cord (In the document pack) R: Printer unit Note: ❏ The shape of the AC plug varies by country; be sure the plug included is the right shape for your loca
Streszczenie treści zawartej na stronie nr. 8
2. Remove the protective materials of the paper ❏ When you place the printer on the base unit, guides from underneath the printer. match the right end square of the printer (shown as 4 in the illustration below) to the square of the same part of the base unit. 3. Position the base unit in front of the printer unit as shown. top view 5. Fasten the bottom of the printer and base unit with wing nuts and washers (I). 4. Mount the printer on the base unit as shown below. Caution: c Do not attem
Streszczenie treści zawartej na stronie nr. 9
7. Remove the protective materials. 2. Likewise, fully insert and attach the long basket hooks (D) to the lower guides. a D b c 3. Turning the stitch side downward, spread the paper basket on the floor. a: from the front cover (tapes) b: from the ink compartment cover (tapes) c: from the side of the print head compartment (fixing metal plate inside the front cover) Caution: c Watch your fingers when opening and closing the front cover. 4. Holding the rear shaft, pass it under the 8. Close t
Streszczenie treści zawartej na stronie nr. 10
6. Hook the both ends of the center shafts (U) on 11. As shown in the figure, hook the paper feed the upper basket hooks. support film on the intermediate shaft of the paper basket, so that it hangs along the inner surface of the basket. Note: Set five paper feed support films at even intervals in the order shown in the figure. U 7. Hold the front side shafts (V) and turn it one revolution as shown below. V 8. Slide out the lower basket hooks to their full length, then attach the L shape e
Streszczenie treści zawartej na stronie nr. 11
❏ Place the front rubber legs of the printer Unpacking the Printer just at the end of the desk. Caution: c ❏ Leave enough room (over 600 mm) in The printer unit is heavy and unwieldy. front of the desk. Have two people unpack the printer. ❏ Prevent your printouts from getting dirty 1. Open the box containing the printer and or crinkled. remove the cardboard panel, the accessory box (A), the roll paper spindle with roll paper, ❏ Use a grounded power outlet. Do not use a and the polystyren
Streszczenie treści zawartej na stronie nr. 12
4. Remove the protective materials: C: Right base (1) and Left base (1) ❏ from the front cover (tape). D: Right leg (1) and Left leg (1) E: Bottom horizontal strut (1) ❏ from the side of the print head compartment (inside the front cover). F: Top horizontal strut (1) G: Basket hooks (4) ❏ from the ink compartment cover (tape). H: Paper basket (1) Tool: I Note: Do not re-install the screw. Store it separately to I:Hex wrench (1) avoid losing it. Accessories: Using the Optional Stand Checking th
Streszczenie treści zawartej na stronie nr. 13
4. Insert the top horizontal strut into the right Assembling the Stand and left legs. Use a screw driver to fasten the strut with + head screws with washers (L). Caution: c Assembly requires two people. Be careful to match the right and left legs (R and L is engraved L on the inner side of the base parts) and base parts. L 1. Insert the right leg into the right base by sliding the leg slot onto the base projection as shown. Fasten the leg to the base with 2 base bolts (J). 5. This complet
Streszczenie treści zawartej na stronie nr. 14
2. Mount the printer on the printer mount as shown. 2. Snap the rear paper basket joints onto the tips of the basket hooks at the rear of the Stand. Make sure the joints are positioned as shown. 3. Fasten the bottom of the printer and the printer mount with wing screws (N) and washers (O). O N O N 3. Rotate the front paper basket joints to enfold the bar which is not attached to the fabric as shown (P). Then, snap the front paper basket joints onto the tips of the basket hooks at the fr
Streszczenie treści zawartej na stronie nr. 15
5. Plug the power cord into a properly grounded Setting up Stylus Pro 7600/9600 electrical outlet. Caution: c Do not use an outlet that is controlled by an Connecting the power cord automatic timer or wall switch. Otherwise, accidental shut down or damage to your 1. Make sure that the printer is off. It is off when printer may occur. the surface of the Power button is even with the button protectors. Installing the ink cartridges To install the ink cartridges, follow the instructions belo
Streszczenie treści zawartej na stronie nr. 16
Note: Loading the Roll Paper If you use the EPSON UltraChrome ink cartridge, shake the cartridge gently before installing it. To load the roll paper onto the printer, follow the instructions below. 1. Slide the movable flange off the end of the spindle. 2. Place the roll paper on a flat surface so that it unwinds in the direction shown. Slide the roll 4. Hold the ink cartridge with arrow mark on the paper onto the spindle and fully onto the fixed left side and pointing to the rear of the
Streszczenie treści zawartej na stronie nr. 17
6. Set the paper lever to the released position. ❏ If the paper does not come out even after executing the procedure above, open the front cover and pull the paper out manually. 9. Holding the bottom edge of the paper, turn the roll paper to remove slack. Make sure that the bottom edge of the paper is straight, and that it is aligned with the rows of the holes. 7. Insert the paper into the paper insertion slot. 10. Set the paper lever to the secured position, and close the roll paper cover
Streszczenie treści zawartej na stronie nr. 18
Using a USB connection (For Windows Me, Reusing the Packaging 98, XP, and 2000) If you need to transport your printer a long To connect the printer to a USB port, you need a distance, the printer should be repacked using the standard shielded USB cable. Follow the steps original boxes and packing materials. Contact below to connect the printer to your computer. your dealer for assistance. Note: The EPSON Printer Port and DMA transfer features Connecting the Printer (For Windows Me, 98, a
Streszczenie treści zawartej na stronie nr. 19
The printer driver runs, or “drives,” your printer; Using the built-in USB interface use it to make settings such as print quality, speed, To use the printer's built-in USB interface, you will media type, and paper size. The Nozzle Check, need a USB interface cable. Then follow the steps Head Cleaning, and Print Head Alignment below to connect the printer to your computer. utilities help you keep your printer in top operating condition. EPSON Status Monitor 3 (for 1. Make sure both the
Streszczenie treści zawartej na stronie nr. 20
4. Choose your printer from the window, then 3. Click the Details tab and make sure that click the right arrow. EPUSBx: (EPSON Stylus Pro 7600/9600) is displayed in the Print to the following port list 5. Click Install Software, then the right arrow. box. 6. Click Install in the dialog box that appears to start the printer software installation. Note: 7. Follow the on-screen instruction. If the correct port is not displayed, refer to the “Troubleshooting” section of the online Reference N
