Streszczenie treści zawartej na stronie nr. 1
Fujitsu Microelectronics Europe
FMEMCU-UG-900001-32
User Guide
F²MC-16LX FAMILY
EVALUATION BOARD
FLASH-CAN-100
USER GUIDE
Streszczenie treści zawartej na stronie nr. 2
Change even page title here Revision History Revision History Date Version Issue 07.12.98 V1.0 P14,P16 connected to JP7, JP8 (RS232 interface for MB90F594A) must be changed 07.12.98 V1.0 Jumper on JP10, JP9 Pin2+3 must be changed to Pin 1+2 to connect to UART1 07.12.98 V1.2 Silk-Plot: Version number must be added. 07.12.98 V1.2 Silk-Plot: SIT/SOT is not correct. Must be changed. 07.12.98 V1.2 Silk-Plot: CAN100BOARD is not correct. 07.12.98 V1.2 Silk-Plot: In RS232 Jumper area - namin
Streszczenie treści zawartej na stronie nr. 3
Change odd page title here Revision History Date Version Issue 23.08.99 V2.2 Table 2. MB90F543 UART0 is wrong – it must be UART1 17.04.00 V2.3 Table 2 corrected now 17.04.00 V2.3 Chapter 1.1. Regarding connectivity problems added. FLASH-CAN-100P-M06 is available again 09.01.01 V2.4 Support added for MB90F42x series 25.01.01 V2.5 Support for MB90F546G/GS and MB90F548G/GS series added, Description of Connector JP11 added 19.09.01 V2.6 Support for MB90440G series added, new disclaimer
Streszczenie treści zawartej na stronie nr. 4
Change even page title here Warranty and Disclaimer Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the FLASH-CAN-100P-M06 Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in accordance with (i) th
Streszczenie treści zawartej na stronie nr. 5
Change odd page title here Contents Contents REVISION HISTORY............................................................................................................ 2 WARRANTY AND DISCLAIMER ......................................................................................... 4 CONTENTS .......................................................................................................................... 5 1 OVERVIEW.............................................................
Streszczenie treści zawartej na stronie nr. 6
Change even page title here Chapter 1 Overview 1 Overview 1.1 Abstract This user guide describes the basic features of the new FLASH-CAN-100P-M06/FLASH- CAN2-100P-M06 board. This board can be used with almost all our 16LX microcontroller series supporting the FPT-100P-M06 package. 1.2 Introduction The "Flash/CAN100"-board was developed in order to support customers and allow a fast software design start. Fujitsu emulators require a target system that provides Vcc and GND as well as an
Streszczenie treści zawartej na stronie nr. 7
Change odd page title here Chapter 2 Features 2 Features < a new 100-pin socket adapter for better connectivity < 7-14V unstabilized external DC power supply possible < 5V and 3.7V internal power supply available < two high-speed CAN drivers < one RS232 interface < two identical pin connectors for all MCU pins < optional sub-clock < RST, HST push-button < 8 User-LEDs < external reset via RS232 < Flash-Programming Software for PC’s The target board will be delivered with the MB9
Streszczenie treści zawartej na stronie nr. 8
Change even page title here Chapter 3 Supported Microcontroller Series 3 Supported Microcontroller Series The target board was designed to work with many microcontrollers from the F²MC-16LX family. As it allows the programming of blank flash devices and supports high speed CAN interfaces, this board is ideal as a test at design start. The following microcontroller series can be used with this board: < MB90420G = MB90V420G, MB90F428GA/GB/GC etc. < MB90435 = MB90V540, MB90F437, MB90F438
Streszczenie treści zawartej na stronie nr. 9
Change odd page title here Chapter 4 Deliverables 4 Deliverables "FLASH-CAN-100P-M06"/"FLASH-CAN2-100P-M06" will be delivered with: < the Flash/CAN100 board itself < two 50pin socket connectors < power supply connector < MB90F598 - 128KB flash microcontroller < 11 Jumper < 1 socket adapter cover < documentation < Flash programming utility – floppy disc For software add-ons please contact your local technical support team for the latest software release or Flash-Programming to
Streszczenie treści zawartej na stronie nr. 10
Change even page title here Chapter 5 Configuration of the Evaluation-Board 5 Configuration of the Evaluation-Board The board is configured to work with the MB90F598 microcontroller. In order to set up the board follow these steps: 1. disconnect power supply disconnected ! 2. Set jumper JP1 to provide Vcc, i.e. 5V to the board 3. If case one is connecting this board to an emulator, it is recommended to set jumper JP2 in order to provide 3.7V to the internal core. 4. Please set the mod
Streszczenie treści zawartej na stronie nr. 11
Change odd page title here Chapter 5 Configuration of the Evaluation-Board 7. Select the appropriate UART interface for the microcontroller you are using by setting jumper JP7-JP10. 8. Please use 1:1 cable for PC-connection. Notes: < Pixx on the silk plot stands for Pinxx, i.e. the pin number. e.g. for the MB90F598, set JP10 and JP9 to connect Pin 1 and 2 in order use UART 1 < MB90425, MB90470, MB90480 and MB90580 series are not supported by jumpers. Please make handwired connection
Streszczenie treści zawartej na stronie nr. 12
Change even page title here Chapter 5 Configuration of the Evaluation-Board 5.1 Modifications for use with MB90470 / MB90480 series Some modifications have to be done in order to use the FLASH-CAN-100P Board together with a MCU of the MB90470 / MB90480 series: 1. Check that U6 is MAX3232CPE 2. Change R6 470 => 390 Ohm. Check that output voltage of U3 is 3.3V (JP2) 3. Disassemble C10 (100nF) 4. Connect J4- Pin 27 to JP10- Pin 2 (SIN) 5. Connect J4- Pin 28 to JP9- Pin 2 (SOT) 6. Connec
Streszczenie treści zawartej na stronie nr. 13
Change odd page title here Chapter 5 Configuration of the Evaluation-Board 5.1.1 Schematic of the modifications for MB90470 / MB90480 © Fujitsu Microelectronics Europe GmbH - 13 - UG-900001-32
Streszczenie treści zawartej na stronie nr. 14
Change even page title here Chapter 6 Using the Asynchronous Boot-Loader 6 Using the Asynchronous Boot-Loader The asynchronous boot-loader SW from Fujitsu can be used to program a blank flash microcontroller. This tool is available on the floppy disc. The following additional steps to chapter 5 need to be taken to set up the hardware (power supply disconnected!): 1. Place the flash microcontroller in its socket (observe pin no. 1 position). 2. Set DIP switch (SW3) : 8 7 6 5 4 3
Streszczenie treści zawartej na stronie nr. 15
Change odd page title here Chapter 7 Connectors 7 Connectors 7.1 Power connector (X1) The following figure shows the power connection jack X1. This connector is used to connect an external unregulated DC power supply voltage (9V-12V DC) to the evaluation board. Shield is connected to positive voltage supply Connector X1: Centre is connected to ground (GND) It is recommended to use 9V to keep the power dissipation to a minimum. Otherwise
Streszczenie treści zawartej na stronie nr. 16
Change even page title here Chapter 7 Connectors 7.4 UART (X4) One 9-pin D-Sub female connectors are used GND DTR RxD TxD for the serial interface (UART). TXD is the transmit output, RXD is the receive input. The DTR signal can be used to generate a reset. 5 1 Please use 1:1 cable for PC-connection. 9 6 Connector X4: CTS RTS DSR 7.5 CAN Interface (X2, X3) Two 9-pin D-Sub male connector are used for the CAN interface. GND CANL Adjust both potentiometer
Streszczenie treści zawartej na stronie nr. 17
Change odd page title here Chapter 8 Silk-Plot of the board 8 Silk-Plot of the board Silk Plot of the new FLASH-CAN2-100P-M06 © Fujitsu Microelectronics Europe GmbH - 17 - UG-900001-32
Streszczenie treści zawartej na stronie nr. 18
Change even page title here Chapter 9 Schematic of the board 9 Schematic of the board UG-900001-32 - 18 - © Fujitsu Microelectronics Europe GmbH
Streszczenie treści zawartej na stronie nr. 19
Change odd page title here Chapter 10 Related Products 10 Related Products < FLASH-CAN-100P-M06 Evaluation-board according to this user guide < MB2132-457 Probe cable for socket: Yamaichi IC149-100-x14-y5 Yamaichi: http://www.yamaichi.de < FLASH-CAN2-100P-M06 New Evaluation board according to this user guide < MB2132-464 Probe cable for socket: Tokyo Eletech: NQPack100rb / HQPack100rb179 Tokyo Eletech: http://www.tetc.co.jp/nq/e_nq_draw.htm < MB2141A/B Emulator debugger main uni
Streszczenie treści zawartej na stronie nr. 20
Change even page title here Chapter 11 Information in the WWW 11 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm Memory products: Flash, SDRAM and FRAM http://www.fme.fujitsu.com/products/memory/index1.html Linear Products: Power Management, A/D and D/A
