Streszczenie treści zawartej na stronie nr. 1
NBG460N
Wireless N Gigabit Router
Quick Start Guide
CONTENTS
Version 3.60
ENGLISH 2
3/2008
Edition 1
DEUTSCH 16
DEFAULT LOGIN
ESPAÑOL 30
IP Address http://192.168.1.1
FRANÇAIS 44
Password 1234
ITALIANO 58
SVENSKA 72
Copyright © 2008. All rights reserved.
Streszczenie treści zawartej na stronie nr. 2
ENGLISH ENGLISH Overview The NBG460N is an IEEE 802.11b/g/n wireless broadband router or access point (AP). As a router, the NBG460N directs traffic between your wireless network and another network such as the Internet as shown below, providing services such as content filtering, bandwidth management and a firewall. This Quick Start Guide shows you how to do the following with your NBG460N in router mode: 1 Connecting Your Hardware 2 Accessing the Web Configurator 3 Connecting to the Intern
Streszczenie treści zawartej na stronie nr. 3
ENGLISH 1 Hardware Connections 2 1 3 Internet 4 Do the following to make hardware connections for initial setup. Antennas 1 Connect each antenna to an antenna socket, ensuring the antennas are screwed in firmly and angled upwards. LAN 2 Connect the Ethernet port on your computer to a LAN port on the NBG460N using the included Ethernet cable. WAN 3 Connect the WAN port on your NBG460N to the Ethernet port on the device with which you are accessing the Internet (for example, a router or modem)
Streszczenie treści zawartej na stronie nr. 4
ENGLISH The LEDs Look at the LEDs (lights). When you connect the power, the power LED ( ) blinks and stays on once the device is ready. The LAN ( ) and WAN ( ) LEDs turn on if the corresponding connections are properly made. If an LED does not turn on, check your connections. If this doesn’t help, disconnect the NBG460N from its power source, wait for a few seconds and turn it back on. 2 Accessing the Web Configurator Default Login Information IP address http://192.168.1.1 administrator
Streszczenie treści zawartej na stronie nr. 5
ENGLISH 2 The Password window displays. Enter the password (“1234” is the default) and click Login. If the login screen does not display, make sure your computer is set to receive an IP address dynamically. If that doesn’t help, check your web browser’s security settings (see the appendix in the User’s Guide for information on both suggestions). 3 Change the password in the screen that follows and click Apply. 4 Click Go to Wizard setup to set up your NBG460N for the first time 3 Connecti
Streszczenie treści zawartej na stronie nr. 6
ENGLISH 2 Click Next in the following screen to proceed with the Connection Wizard. Enter the Internet access information exactly as given to you by your ISP in each wizard screen. Click Next to continue or click Back to return to the previous screen. Current screen information will be lost if you click Back. 3.1 System Information This screen is optional. You can just click Next. 3.2 Wireless LAN Configure your NBG460N to support a wireless network by following these steps. 1 Enter a unique
Streszczenie treści zawartej na stronie nr. 7
ENGLISH 3 Write down the security key that displays in the pop-up screen. Computers on the wireless network will need this security key to access the NBG460N. The security key is case- sensitive so “ABCD” is not the same as “abcd”. Write down the security key, Name (SSID), Security and Channel Selection for later use as the NBG460N and other devices on your wireless network must use the same settings. 4 Click OK to continue. 3.3 WAN Connection You may need to wait several minutes while t
Streszczenie treści zawartej na stronie nr. 8
ENGLISH Ethernet Connection Select Ethernet as your WAN connection type and click Next to go to section 3.4. PPP over Ethernet Connection 1 Select PPP over Ethernet as your WAN connection type 2 Type a Service Name (if your ISP gave you one), User Name and Password. Click Next to go to section 3.4. PPTP Connection 1 Select PPTP as your WAN connection type. 2 Type a User Name and Password. 3 Type a PPTP Server IP Address. 4 Type a Connection ID/Name (if provided by your ISP). 5 If your ISP d
Streszczenie treści zawartej na stronie nr. 9
ENGLISH 7 Click Next to go to section 3.4. 3.4 WAN IP Address • If your ISP did not assign you a fixed IP address, select Get automatically from your ISP and click Next to go to section 3.5. • If your ISP gave you a fixed IP address: 1 Select Use fixed IP address provided by your ISP. Click Next. 2 In the next screen type the WAN IP address, WAN IP Subnet Mask and the gateway IP address given by your ISP. If you were given DNS server settings, type them in the fields. Otherwise leave the de
Streszczenie treści zawartej na stronie nr. 10
ENGLISH •Select Factory Default to use the factory-assigned, default MAC address. •Select Clone the Computer’s MAC Address to clone the MAC address from a computer on your LAN. Type the IP address of the computer with the MAC address you are cloning. It is advisable to clone the MAC address from a computer on your LAN even if your ISP does not presently require MAC address authentication. •Select Set WAN MAC Address if you know the MAC address you want to use. 3.6 Bandwidth Management Select
Streszczenie treści zawartej na stronie nr. 11
ENGLISH If you cannot access the Internet when your computer is connected to one of the NBG460N’s LAN ports, check your connections. Then turn the NBG460N off, wait for a few seconds and turn it back on. If this doesn’t work run the wizard again, making sure you type the information correctly. Also, if you are using a new Internet account, contact your ISP to make sure it is active. See Troubleshooting in the User’s Guide for more suggestions. 4 Set Up a Wireless Network You can use Wi-Fi
Streszczenie treści zawartej na stronie nr. 12
ENGLISH 2 Press the WPS button on both devices. It doesn’t matter which button is pressed first. You must press the second button within two minutes of pressing the first one. 2 minutes Your NBG460N has a WPS button located on its housing, as well as a WPS button available in the web configurator used to manage the NBG460N. Other WPS-enabled devices should have at least one similar WPS button. 3 The WPS LED ( ) on the NBG460N blinks for a few seconds, then shines steadily. 4 Check if your
Streszczenie treści zawartej na stronie nr. 13
ENGLISH 4.2 Set up a Wireless Network Manually You can now connect wirelessly to your NBG460N from your computer and access the Internet. You will need the Network Name (SSID) and also the Security Key (Pre-Shared Key) if you set up security in the previous section. The connection procedure is shown here using Windows XP as an example. 1 Right-click the wireless adapter icon which appears in the bottom right of your computer monitor. Click View Available Wireless Networks. 2 Select the SSI
Streszczenie treści zawartej na stronie nr. 14
ENGLISH If you cannot connect wirelessly to the NBG460N, check you have selected the correct SSID and entered the correct security key. If that does not work, ensure your network adapter is enabled by clicking on the wireless adapter icon and clicking Enable. See the User’s Guide for more suggestions. Procedure to View a Product’s Certification(s) 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3 Select the certi
Streszczenie treści zawartej na stronie nr. 15
ENGLISH 15
Streszczenie treści zawartej na stronie nr. 16
DE DEUTSCH UTSCH Übersicht Der NBG460N ist ein drahtloser IEEE 802.11b/g/n-Breitbandrouter und Access-Point (AP). Als Router leitet der NBG460N den Datenverkehr zwischen dem Drahtlosnetzwerk und einem anderen Netzwerk wie dem Internet wie unten dargestellt weiter und bietet Dienste an wie Inhaltsfilter, Bandbreitenverwaltung und Firewall. In dieser Kurzanleitung erfahren Sie, wie Sie Folgendes mit Ihrem NBG460N im Router- Modus einrichten können: 1 Anschließen der Hardware 2 Zugreifen auf den
Streszczenie treści zawartej na stronie nr. 17
DEUTSCH 1 Anschließen der Hardware 2 1 3 Internet 4 Bei der Erstinstallation müssen die folgenden Hardwareverbindungen hergestellt werden: Antennen 1 Schließen Sie alle Antennen an den jeweiligen Antennenanschluss an. Stellen Sie sicher, dass die Antennen fest eingedreht sind und aufrecht ausgerichtet sind. LAN 2 Schließen Sie Ihren Computer mit dem mitgelieferten Ethernet-Kabel an einen "LAN"-Anschluss an. WAN 3 Schließen Sie Ihr Modem mit dem mitgelieferten Kabel an den "WAN"-Anschluss an.
Streszczenie treści zawartej na stronie nr. 18
DEUTSCH Die LED-Anzeigen Das Gerät verfügt über LED-Anzeigen. Wenn Sie das Gerät an das Stromnetz anschließen, beginnt die LED-Anzeige ( ) zu blinken. Wenn es bereit ist, hört sie auf zu blinken und leuchtet stetig. Die LED-Anzeigen LAN ( ) und WAN ( ) beginnen zu leuchten, wenn die entsprechenden Verbindungen bestehen. Sollte eine LED nicht leuchten, prüfen Sie die Verbindung. Leuchtet sie auch dann nicht, trennen Sie den NBG460N von seiner Stromquelle, und schalten Sie ihn einige Sek
Streszczenie treści zawartej na stronie nr. 19
DEUTSCH 2 Das Fenster Password (Kennwort) erscheint. Geben Sie das Kennwort ein ("1234" ist das Standardkennwort), und klicken Sie auf Login (Anmelden). Wenn das Anmeldefenster nicht angezeigt wird, stellen Sie sicher, dass der Computer so eingestellt ist, dass er eine dynamische IP-Adresse bezieht. Wenn das Problem dadurch nicht behoben ist, prüfen Sie die Sicherheitseinstellungen Ihres Webbrowsers (Informationen zu beiden Möglichkeiten finden Sie im Anhang des Benutzerhandbuchs). 3 Ände
Streszczenie treści zawartej na stronie nr. 20
DEUTSCH 3 Assistent zum Einrichten der Verbindung 1 Sprache wählen. Klicken Sie auf Next (Weiter). 2 Klicken Sie auf Next (Weiter) und fahren Sie mit dem Connection Wizard (Verbindungsassistent) fort. Geben Sie die Daten für den Internetzugriff so ein, wie Sie sie von Ihrem Internetdienstanbieter erhalten haben. Klicken Sie zum Fortfahren auf Next (Weiter) oder auf Back (Zurück), um zum vorhergehenden Fenster zurückzukehren. Wenn Sie auf Back (Zurück) klicken, gehen alle aktuell auf dem Bi
